Related Manuals for Advantech SPC-815
Summary of Contents for Advantech SPC-815
- Page 1 User Manual SPC-815(M) SPC-821(M) BOR-DE115W BOR-DE121W 顯示器 W15.6” / W21.5 ” TFT LED LCD Standalone Multi-Touch Industrial Monitor with Extension Units...
- Page 2 The documentation and the software included with this product are copyrighted 2020 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to improve the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
- Page 3 Product Warranty (2 years) Advantech warrants the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation.
- Page 4 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
- Page 5 Safety Instructions Read these safety instructions carefully. Retain this user manual for future reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or spray detergents. For pluggable equipment, the power outlet socket should be located near the equipment and easily accessible.
- Page 6 Le niveau de la pression acoustique à la position de l'opérateur, conformément à la norme CEI 704-1: 1982, ne dépasse pas 70 dB (A). AVIS DE NON-RESPONSABILITÉ: Cet ensemble d'instructions est donné conformé- ment à la CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des déclarations contenues dans ce document. –...
- Page 7 MÊME TYPE OU ÉQUIVALENT RECOMMANDÉ PAR LE FAB- RICANT, JETER LES BATTERIES USÉES SELON LES INSTRUCTIONS DU FABRICANT. VEUILLEZ CONTACTER LE FABRICANT, ADVANTECH, POUR LE REMPLACER. ATTENTION! Pour éviter les chocs. Ne pas retirer lecouvercle. Aucune pièce réparable par l’utilisa- teur. Pour l’entertien adressez-vours aux personnes qulifiées, s.v.p.
- Page 8 安全指示 請仔細閱讀此安全操作說明。 請妥善保存此用戶手冊供日後參考。 用濕抹布清洗設備前，請確認拔除電源線。請勿使用液體或去污噴霧劑清洗設 備。 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。 請勿在潮濕環境中試用設備。 請在安裝前確保設備放置在可靠的平面上，意外摔落可能會導致設備損壞。 設備機殼的開孔適用於空氣對，從而防止設備過熱。請勿覆蓋開孔。 當您連接設備到電源插座前，請確認電源插座的電壓符合要求。 請將電源線佈置在人們不易絆倒的位置，請勿在電源線上覆蓋任何雜物。 請注意設備上所有的警告標示。 如果長時間不使用設備，請拔除與電源插座的連結，避免設備被超標的電壓波動 損壞。 請勿讓任何液體流入通風口，以免引起火灾或短路。 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。 如遇下列情况，請由專業人員維修： – 電源線或插頭損壞； – 設備內部有液體流入； – 設備曾暴露在過度潮濕環境中使用； – 設備無法正常工作，或您無法透過用戶手冊來正常工作； – 設備摔落或損壞； – 設備有明顯外觀損； 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 -20 ℃ （-4 ℉）或高 於 60 ℃ （140 ℉） ，否則可能會造成設備損壞。 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一...
-
Page 9: Table Of Contents
Packing List for BOR-DE Series (Customize model for Customer) Specifications .................... 4 1.3.1 Without Button extension & IO RJ-45 Port for built in SPC-815- M7AG & SPC-821-M7AG Multi Touch Industrial Monitor ..... 4 1.3.2 Without Button extension for built in SPC-815-MLAG & SPC-821- MLAG Multi Touch Industrial Monitor.......... - Page 10 SPC-800(M) User Manual...
-
Page 11: Chapter 1 General Information
Chapter General Information... -
Page 12: Introduction
Introduction The SPC-800(M) series devices with a brand-new ID design can support an all- around IP65 waterproof casting design with general I/O connectors, with I/O cover all the wiring & cabling can be hidden invisible to ensure reliability & field wire simplicity. SPC-800(M) is a hardware-solution based HMI product which supports industrial grade ARM/VESA mount system and push button extension supported. -
Page 13: Packing List
Packing List 1.2.1 Packing List for SPC-800(M) Series 1 x System 1 x Plug-In Block 1 x Ground Wire (100CM) 1 x Cover IO 1 x Registration and Warranty Card 4 x Pole Mounting Blake Screws ... -
Page 14: Specifications
Specifications 1.3.1 Without Button extension & IO RJ-45 Port for built in SPC-815- M7AG & SPC-821-M7AG Multi Touch Industrial Monitor Advantech Part Number SPC-815-M7AG SPC-821-M7AG 6.8g(W/O ARM Mount) 9.6g(W/O ARM Mount) Weight 7.2g(W ARM Mount) 10Kg(W ARM Mount) 7.6Kg(W Vesa Mount) 10.4Kg(W Vesa Mount) - Page 15 Emergency button Without Emergency Button Push button Without Push Button Cable Button Without Button SPEC Button Cover Without Button Color Humidity 85% @ 40°C (non-condensing) Operating 0 ~ 55°C (without airflow) Temperature Storage Tempera- -20 ~ 60°C ture Environ- ment Degree and class IP65 (All around) of protection...
-
Page 16: Without Button Extension For Built In Spc-815-Mlag & Spc-821- Mlag Multi Touch Industrial Monitor
1.3.2 Without Button extension for built in SPC-815-MLAG & SPC- 821-MLAG Multi Touch Industrial Monitor Advantech Part Number SPC-815-MLAG SPC-821-MLAG 6.8g(W/O ARM Mount) 9.6g(W/O ARM Mount) Weight 7.2g(W ARM Mount) 10Kg(W ARM Mount) 7.6Kg(W Vesa Mount) 10.4Kg(W Vesa Mount) 402.19mm x 333.19mm x 67mm 546.69mm x 420.34mm x 67mm... - Page 17 Emergency button Without Emergency Button Push button Without Push Button Button Cable Button Without Button SPEC Button Cover Without Button Color Humidity 85% @ 40°C (non-condensing) Operating 0 ~ 55°C (without airflow) Temperature Storage Tempera- -20 ~ 60°C ture Environ- ment Degree and class IP65 (All around)
-
Page 18: Button Extension & Without Io Rj-45 Port For Built In Spc-815- M7Ap & Spc-821-M7Ap Multi Touch Industrial Monitor
1.3.3 Button extension & Without IO RJ-45 Port for built in SPC-815- M7AP & SPC-821-M7AP Multi Touch Industrial Monitor Advantech Part Number SPC-815-M7AP SPC-821-M7AP 6.8g(W/O ARM Mount) 9.6g(W/O ARM Mount) Weight 7.2g(W ARM Mount) 10Kg(W ARM Mount) 7.6Kg(W Vesa Mount) 10.4Kg(W Vesa Mount) - Page 19 Humidity 85% @ 40°C (non-condensing) Operating 0 ~ 55°C (without airflow) Temperature Storage Tempera- -20 ~ 60°C ture Environ- ment Degree and class IP65 (All around) of protection Shock Protection IEC 60068-2-27 Vibration IEC 60068-2-64 (Random 2G) Protection CE MARK Certifi- UL62368 approval YES cates...
-
Page 20: Button Extension For Built In Spc-815-Mlap & Spc-821-Mlap Multi Touch Industrial Monitor
1.3.4 Button extension for built in SPC-815-MLAP & SPC-821-MLAP Multi Touch Industrial Monitor Advantech Part Number SPC-815-MLAP SPC-821-MLAP 6.8g(W/O ARM Mount) 9.6g(W/O ARM Mount) Weight 7.2g(W ARM Mount) 10Kg(W ARM Mount) 7.6Kg(W Vesa Mount) 10.4Kg(W Vesa Mount) 402.19mm x 333.19mm x 67mm 546.69mm x 420.34mm x 67mm... - Page 21 Emergency button RAFI 22 FS+ (2NC) 1.30.273.511/0300 Emergency Stop button *1 RAFI 22 FS+ Push button (1NC1NO) ,Green(1.30.270.021/ Push button Button 2500),Red (1.30.270.021/2300),Blue (1.30.270.021/2600) Button Cable 28# , support 24V 0.5A SPEC Humidity 85% @ 40°C (non-condensing) Operating 0 ~ 55°C (without airflow) Temperature Storage Tempera- -20 ~ 60°C...
-
Page 22: Button Extension For Built In Bor-De115W & Bor-De121W Multi Touch Industrial Monitor (Customize Model For Customer)
1.3.5 Button extension for built in BOR-DE115W & BOR-DE121W Multi Touch Industrial Monitor (Customize model for Customer) Advantech Part Number BOR-DE115W-B100A BOR-DE121W-B100A 6.8g(W/O ARM Mount) 9.6g(W/O ARM Mount) Weight 7.2g(W ARM Mount) 10Kg(W ARM Mount) 7.6Kg(W Vesa Mount) 10.4Kg(W Vesa Mount) 402.19mm x 333.19mm x 67mm... -
Page 23: Power
This product is intended to be supplied by a Listed Power Adapter or DC power source, rated 24Vdc, 2.5A minimum and TMA 55 degree C minimum, if need further assistance, please contact Advantech for further information. SPC-800(M) User Manual... -
Page 24: I/O Ports Arrangement
I/O Ports Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.1 Front view and Side view Figure 1.2 Rear view for SPC-800-MLAG/SPC-800-MLAP Series SPC-800(M) User Manual... - Page 25 Figure 1.3 Rear view for SPC-800-M7AG/SPC-800-M7AP Series SPC-800(M) User Manual...
-
Page 26: Dimensions
Dimensions SPC-815(M), BOR-DE115W Weight: 7.83kg Dimensions (W x H x D): 402 x 333 x 67mm (15.83" x 13.11" x 2.64") Figure 1.4 SPC-815 (M)& BOR-DE115W Dimensions SPC-800(M) User Manual... - Page 27 SPC-821(M) & BOR-DE121W Weight: 10.63kg Dimensions (W x H x D): 547 x 420 x 67 mm (21.54” x 16.54” x 2.64”) Figure 1.5 SPC-821(M) & BOR-DE121W Dimensions SPC-800(M) User Manual...
- Page 28 SPC-800(M) User Manual...
-
Page 29: Chapter 2 System Setup
Chapter System Setup... -
Page 30: Scope Of Delivery
Scope of Delivery You can easily get SPC-800 started by following the below steps. The SPC- series. Unpack the SPC package. Check the packing list at the beginning of this manual to make sure all items have been included. Figure 2.1 Unpack the Package The following components are included in the scope of delivery of the SPC-800 device. -
Page 31: System Setup
Mounting the SPC-800(M) device The section describes the mounting of the device to a support ARM or VESA system using example figures.SPC-815 and SPC-821 are the same design and same com- ponent for Pendant and Pedestal mounting.(no additional component is needed) And VESA mount is optional. -
Page 32: Spc-800 Device For Support Arm Mounting
IO. If you install the device with an ARM mount- ing, you must the corresponding relative size and screw hole position can support the weight of the device or purchase a pole with Advantech Requirement Pole Mount x 1pc ... - Page 33 Attach the IO with M5 or M6 x 4pcs screws to the interface of the support pole mount. Fasten the OP bracket with cover IO by the screw. SPC-800(M) User Manual...
- Page 34 Attach the device with M5x 4pcs screws to the IO from back side. Make sure that the connection cables whether put into the pole mount. Installation Procedure (Pendant and Pedestal mounting) Loosen the M5 x 4pcs screws from IO (Pedestal mount) SPC-800(M) User Manual...
-
Page 35: Spc-800(M)/Bor-De1000 Series Device For Support Vesa Mounting
IO. If you install the device with a VESA mounting, you must use 100 x100 standard VESA compliant hole to allow wall and accessory mounting option and can purchase the cable suitable for you through Advantech Entry Requirement VESA Kit x 1pc ... - Page 36 Cable Entry Cover x 1pcs Cable Entry x 1pcs (Choose the suitable for equipment application) Item Product Specifications Figure Rating Split cable entry system KEL-ER-E5 for rout- IP65 ing and Sealing up to 5 cables with connector IP66 (Cable diameters from 1 to 16 mm) Split cable entry system KEL-ER 10 for rout- ing and sealing cables with connectors,...
- Page 37 icoteck Round cable 4-5 mm 41304 KT 4 bk icoteck Round cable 3-4 mm 41303 KT 3 bk icoteck Blank grommet 41351 BTK bk Installation Procedure Install VESA ARM to the VESA adapter by M4 x 4pcs screws. Fix 2 pcs of M5 screws into upside screw holes. SPC-800(M) User Manual...
- Page 38 Fit into two holes with two screws Fix 2 pcs of M5 screw into the body through the holes downside in the VESA kit. SPC-800(M) User Manual...
- Page 39 Arrange the cables through the opening of the cover and fix the cover by M5 x 4pcs screws. Fix the cables in the entry frame by 3pcs M5 screws and fix the entry to body by 2pcs M5 screws. Fix the cover to body by 6pcs M3 screws. SPC-800(M) User Manual...
-
Page 40: Spc-800(M) Extension With Operator Controls
The following example shows a SPC-800(M) device with an Extension Unit. SPC-800(M) device with operator controls extension can order these components (Push Button, PCBA, terminal plug and Screw) do it by yourself assembly or Com- prehensive assembly also via Advantech (Build To Order) SPC-800(M) User Manual... - Page 41 Base Unit design for Extension Unit The Base Unit design is support to RAFI RAFIX 22 Buttons, and the rightmost button is reserved for Emergency Stop Button Push-button. And the other side design for Front USB location. Push Push Push Emergency Stop Button Button...
- Page 42 Freely configuration do it by yourself assembly Terminal Board PIN Define Push Button of Type Description Picture RAFIX 22 FS+ - Emergency stop pushbutton, not illuminable, reset by rotation, red arrows 1.30.273.511/0300 RAFIX 22 FS+ - Pushbutton, illuminated, flush lens, round collar, metal front ring, momentary 1.30.270.021/2200 RAFIX 22 FS+ - Drucktaster nicht beleuchtbar , flache Blende,...
- Page 43 Loosen the M3 x6pcs screw and loosen the M3 x6pcs screw of OP back side Note! SPC-815 series are need loosen M3 x16L *4pcs and M3 x 6L*4pcs of OP back side SPC-821 series are need loosen M3 x16L *6pcs and M3 x 6L*6pcs of...
- Page 44 Pre-hole cut-outs Fix the RAFI button assembly of the threaded ring. Attach the Button’s PCBA with M3 x 4pcs screw to the OP back side. SPC-800(M) User Manual...
- Page 45 Fasten the OP back side by the screw. Install the terminal Board with M3 x 4pcs screws. SPC-800(M) User Manual...
- Page 46 SPC-800(M) User Manual...
-
Page 47: Appendix Aosd Operating Process
Appendix OSD Operating Process... -
Page 48: Osd Board Overview (Spc-800)
OSD Board Overview (SPC-800) The OSD keypad, including two keys and a two-color indicator, is designed as the HMI Touch glass printing device. A.1.1 OSD Button Description icon Indicator Status intelligent Selected option Activate the OSD menu Enter/confirm the selected option Decreases and Increases brightness Home Changes Input video source... -
Page 49: Led Functions
A.1.2 LED Functions Indicator Status Blue Power on Orange Stand By No lights Power Off OSD Key Functions Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out. -
Page 50: Brightness Select
A.2.2 Brightness Select Select “Brightness” function by Press Home key, and continue Press Home key for selection confirmation (Range: 0~100) A higher value will make the picture appear brighter A.2.3 Video Input Select “Video Input” function by Press Home key, Press the Input Selection that corresponds with the video source device. - Page 51 Note! The No Signal message means and LED indicator is Orange that the device isn’t getting any video input from the currently selected source. If “No Signal” message appear, please try to adjust the current selected video input mode: DP Source: Make sure the DP connection is enable on the device. To do it, ...
-
Page 52: Pip (Picture-In-Picture)
A.2.4 PIP (Picture-in-Picture) Select “PIP” function by Press Home key and selection that corresponds with the PIP connection mode. The size and position of the smaller screen can all be adjusted in PIP function. There is limited combination of video input to fulfill PIP, listed below: DP + HDMI ... -
Page 53: Touch
A.2.5 Touch Select “Touch” function by Press Home key and can adjust Touch function mode. Always Off: to disable touch function to ensure mis-touch. Off for 60 sec: to disable touch function and after 60 seconds the touch function will be enabled automatically. - Page 54 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2020...