Related Manuals for Advantech ES-3115 G-XA
Summary of Contents for Advantech ES-3115 G-XA
- Page 1 ES-3115 G/R/C/S/V - XA 15" Open-Frame LCD Monitor with Anti-glare Glass/ Resistive / Capacitive / 3mm SAW / 6 mm Vandal Proof SAW Touchscreens...
-
Page 2: Copyright Notice
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. -
Page 3: Packing List
1. Visit Advantech sites www.advantech.com www.advantech.com.tw where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: •... -
Page 4: Safety Instructions
Safety Instructions Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. -
Page 5: Table Of Contents
Contents Chapter 1 Introduction ........... 1 1.1 Introduction..............2 1.2 Product Features ............. 3 1.3 VGA Signal ............... 4 1.4 LCD Specification............5 1.4.1 LCD Specification ..........5 1.4.2 LCD Pin Definition ..........6 1.5 Touchscreen Specification ..........7 1.6 External AC Power Adaptor..........8 1.7 Environment.............. - Page 6 Figures Figure 2-1: Rear view of the ES-3115 C/R/S/SV-XM......………16 Figure 3-1: Dimensions of the ES-3115 C/R-XM ..........23 Figure 3-2: ES-3115 C/R-XM Dimensions of cutoff and panel mounting holes ................…..24 Figure 3-3: ES-3115 S/SV-XM Dimensions of cutoff and panel mounting holes ................25 Figure 3-4: Rear mounting of the ES-3115 C/R-XM .........
- Page 7 CHAPTER General Information This chapter includes: • Introduction • Product Features...
-
Page 8: Chapter 1 Introduction
1.1 Introduction This product, LCD touch monitor, is mainly focused on Kiosk market or Human Machine Interface (HMI). It is a core module for Kiosk application. The LCD touch monitor supports direct VGA analog signal inputs, which make it more compatible and adaptable to connect to computers widely used in the current market. -
Page 9: Product Features
1.2 Product Features General • Construction: steel chassis • Dimensions for G/R/C/S/V (W x H x D): 414 mm x 322.2 mm x 500 mm • Weight: 4.1 kg • Mounting: rear mounting • 15" TFT active matrix LCD display: XGA resolution of 1024 x 768 pixels with 262144 colors. - Page 10 • Display mode support: Item Resolution V Freq.(Hz) Note Freq.(kHz) 640x400@70 31.469 70.087 640x480@60 31.469 59.940 VESA 640x480@66 35.000 66.667 640x480@72 37.861 72.809 VESA 640x480@75 37.500 75.000 VESA 720x400@70 31.469 70.087 TEXT 800x600@56 35.156 56.250 VESA 800x600@60 37.879 60.317 VESA 800x600@72 48.077 72.188...
-
Page 11: Lcd Specification
1.4 LCD Specification 1.4.1 LCD Specification DF-14H-20P-1.25H (Hirose) or CWY20G-A0D1T (PTWO) Pin No. Symbol Description Display Type 15” XGA TFT LCD Active Area (mm) 304.128 X 228.096 Resolution 1024 X 768 Dot Pitch (mm) 0.297 X 0.297 Supply Voltage (Panel) 12 Vdc Viewing angle (v,h) 80°, 120°... -
Page 12: Lcd Pin Definition
1.4.2 LCD pin definition M150XN07 pin definition is shown in the table below. Power Supply, 3.3V (typical) Power Supply, 3.3V (typical) Ground Ground Rin0- - LVDS differential data input (R0-R5, G0) Rin0+ + LVDS differential data input (R0-R5, G0) Ground Rin1- - LVDS differential data input (G1-G5, B0-B1) Rin1+... -
Page 13: Touchscreen Specification
1.5 Touchscreen Specification 1.5.1 ES-3115C (Capacity) • Type: 3M Touch Systems Microtouch capacity touch screen • Resolution: 1024 x 1024 • Light Transmission: 85% • Touch Life Cycle: 225 million • Controller: RS-232 interface • Communication speed: up to 19.2K baud. •... -
Page 14: External Ac Power Adaptor
1.6 External AC Power Adapter Output: 12Vdc/4.0A • Input: 100 ~ 240 Vac, 47 ~ 63 Hz, 1.2A • Efficiency: better than 84% under maximum load. • MTBF: 50,000 hr at 25°C • 1.7 Environment ° Temperature: 0°C ~ 45°C (32 ~112 •... -
Page 15: Chapter 2 System Setup
CHAPTER System Setup • Introduction • Preparing for First-time Use • I/O arrangement • Installation Procedure • OSD Control • Enabling the Touchscreen... -
Page 16: Introduction
2.1 Introduction This chapter describes basic features and procedures for using the Open-frame LCD monitor. Topics covered include the system installation, OSD control, Touchscreen, and so on. 2.2 Preparing for First-time Use Before you start to set up the ES-3115 LCD Monitor, You should have at least the following items ready in your accessory box: •... -
Page 17: Installation Procedure
2.4 Installation Procedure The ES-3115 can only be powered by an AC electrical outlet adapter (90 ~ 240 volts). Be sure to always handle the power cord and power adapter by holding the plug ends only. 1. Make sure that the system power is turned off. 2. - Page 18 2. [Menu] (Menu KEY) is designated for Menu/Enter function depending on the selected item. Pressing [Menu] can invoke OSD menu. After that, [Menu] is also an entry key. 3. [← /↑] (INC KEY) is designated for selection function in up direction in OSD menu and also to increase the value on selected function.
-
Page 19: Enable The Capacity Touchscreen (Es-3115C-Xm)
noise on the screen while adjust the Clock. Press” INC” or “DEC” to adjust the parameter Adjusts the video distortion. It will appear vertical noise on the screen while adjust the Phase Press” INC” or “DEC” to adjust the parameter Move the display picture Press”... -
Page 20: Enable The Resistive Touchscreen (Es-3115R-Xm)
and etc. ES-3115C-XA provides 1 CD kit which contain capacitive driver. It enables you to use the capacitive touchscreen with applications running in Windows environments. You can run Windows programs and use touch input without any program modification. 1. Make sure the RS-232 cable is properly connected. The Setup program cannot configure the touchscreen without it. - Page 21 The SAW touchscreen of ES-3115S-XA is patented technology available from Elotouch System. Its tough, scratch-resistant and wear-resistant feature is an ideal choice for unattended kiosks and POI applications in public places like train stations, airports, malls, supermarket, and etc. ES-3115V-XA provides 1 CD kit which contain SAW driver. It enables you to use the resistive touchscreen with applications running in Windows environments.
- Page 22 carefully when answering questions to complete the installation.
-
Page 23: Figure 3-1: Dimensions Of The Es-3115 C/R-Xm
CHAPTER Specification • Introduction • Mechanical Dimension • Cut-out Dimensions for Rear Mounting • Mounting Guide • Exploded Diagram • Electrical Block Diagram • ADC Board • DC to DC Power Board • DC to AC Inverter • Touchscreen Control Board... -
Page 24: Introduction
3.1 Introduction The mechanical design concept of ES-3115 G/ R/C/ S/ V -XA follows easy assembling, easy maintenance principles. Two main metal parts are used to support PCB, LCD panel, and touch screen. Basically, front frame and back frame form a space to contain all parts of LCD touch monitor. The back frame metal plate are used to mount PCB boards and LCD panel, front metal frame is used to mount the Touchscreen. -
Page 25: Mechanical Dimension
3.2 Mechanical Dimension Mechanical Dimension of ES-3115G/R/C/S/V-XA 414.00 396.00 300.00 210.50 50.00 278.40 377.60 Figure 3-1: Dimensions of the ES-3115G/R/C/S/V–XA... -
Page 26: Figure 3-4: Rear Mounting Of The Es-3115 C/R-Xm
3.3 Cut-out Dimension for ES-3115 G/R/C/S/V-XA Rear Mounting To construct a suitable panel, refer to the following cutout & elongated holes dimension diagram. 306.00 SUGGESTED Display opening size Figure 3-3: ES-3115 G/R/C/S/V–XA dimensions of cut-off. -
Page 27: Mounting Guide
3.4 Mounting guide To mount the ES-3115G/R/C/S/V-XA into a panel or kiosk: 1. Build 8 screw studs along the four sides of the cut out opening based on the dimension given on the drawing above. 2. There are ten elongated holes located along the four sides of the open frame monitor. -
Page 28: Mounting Guide Of Es-3115 C/R-Xm
3.5 Mounting guide 3.5.1 Exploded Diagram of ES-3115 G/R/C-XA Figure 3-6: Exploded diagram of the ES-3115 G/R/C-XA... -
Page 29: Exploded Diagram Of Es-3115 S/Sv-Xm
3.5.2 Exploded Diagram of ES-3115 S/ V –XA Figure 3-7: Exploded diagram of the ES-3115S/ V –XA... -
Page 30: Electrical Block Diagram
3.6 Electrical Block Diagram According to the product idea, 15"” LCD panel and touchscreen are the basic two components in this product. Besides, in order to reduce the depth of LCD touch monitor and solve cooling problem at the same time, a DC input is designed to remove the AC switching power supply. -
Page 31: Adc Board
3.7 ADC Board The ADC board is used to convert RGB signal to LCD digital signal and send to LCD panel to display. The ADC board is as below: Figure 3-9: Locating connectors on ADC board... -
Page 32: Dc To Ac Inverter
3.8 DC to AC Inverter The DC/AC inverter is used to provide the power to LCD backlight. The inverter is as below: Figure 3-10: Locating connectors on DC/AC inverter... -
Page 33: Touchscreen Control Board
3.9 Touch Screen Control Board Except ES-3115G-XA, all other ES-3115 series provide various touch screen with different technical. For ES-3115C-XA, it use 3M MicroTouch’s Capacity Touch Screen sensor and has the control board as below: Figure 3-11: Locating connector of ES-3115C control board ES-31153115R-XA used the ELO’s resistive touch screen as below: Figure 3-12: Locating connector of ES-3115R control board... -
Page 34: Figure 3-13: Locating Connector Of Es-3115S And Es-3115Sv Control Board
ES-3115S-XA and ES-3115V-XA used the ELO’s Surface Wave touch screen as below: Figure 3-13: Locating connector of ES-3115S and ES-3115V control board...