Do you have a question about the Prodigy 2.0+ Lumbar and is the answer not in the manual?
Questions and answers
Jon
February 22, 2025
For L&P prodigy2. The lumbar (pillow) moves only one way. The polarity in the OKIN control box doesn’t change.
1 comments:
Mr. Anderson
May 14, 2025
If the lumbar pillow on a Leggett & Platt Prodigy 2 only moves one way and the polarity in the OKIN control box does not change, the issue could be a malfunction in the control box that prevents it from reversing the motor polarity. This would stop the lumbar motor from moving in both directions.
This answer is automatically generated
Related Manuals for Leggett & Platt Prodigy 2.0+ Lumbar
CONTENTS Advisory ........................4 Assembly ........................6 Remote Control Function .................... 10 Remote Control Programming ..................11 Power Down Operation ....................14 Troubleshooting ......................16 Accessories ....................... 17 1-3-25 Warranty ......................18 READ ALL INSTRUCTIONS BEFORE USING If adjustable base does not operate or if parts are missing, call: 1-800-888-3078...
ADV ISORY IMPORTANT INFORMATION READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT MASSAGE OPERATION WARNING The massage feature will emit a minimal tone during operation. This is normal. When the massage level is FOR OPTIMUM ADJUSTABLE BASE increased, motor resonance will intensify accordingly. OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT LOCATION ENV IRONMENT...
Page 4
ADV ISORY IMPORTANT INFORMATION READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT HOSPITAL USE DISCLAIMER PACEMAKER WARNING This base is designed for in-home use only. It This product produces a vibrating sensation. is not approved for hospital use and does not It is possible that individuals with heart-assist comply with hospital standards.
ASSEMBLY To assemble adjustable base, complete the following procedure: STEP 1 Open the base shipping carton and verify the following items are included: (includes power brick, electrical feed cord, and electrical power cord) WARRANTY ACTIVATION CARD (split sizes only) OWNERS MANUAL QUICK SETUP GUIDE (4 pieces) MATTRESS...
Page 6
ASSEMBLY STEP 2 WARNING Extend the main power cord out head end of base. Set the hardware box aside. Cut the zip-tie POWER CORDS MUST NOT INTERFERE WITH and remove the mattress retainer. ANY ADJUSTABLE BASE MECHANISMS. DO NOT WEAVE CORDS THROUGH BASE STEP 3 STRUCTURE.
Page 7
ASSEMBLY STEP 5 Remove remaining packaging and any protective film. STEP 6 Plug the base into an electrical power source. Note: An electrical surge protection device is recommended, but not included. STEP 7 Install 3-AAA batteries in the remote control (FIGURE 3). Operate remote control to verify base functions properly.
Page 8
ASSEMBLY MATTRESS RETAINER INSTALLATION (OPTIONAL) Base is equipped with a Micro-Hook™ system to captivate the mattress as shown in FIGURE 4, but a mattress retainer can also be used. Important: If using a dust ruffle or mattress encasement with this product, a mattress retainer must be used.
REMOTE CONTROL FUNCTION UNDERBED LIGHT BUTTON SNORE BUTTON Press to turn underbed light on. Press Press and hold to raise head to the again to turn underbed light off. preprogrammed position. Head will automatically lower to flat after 15 LOCK BUTTON minutes.
REMOTE CONTROL PROGRAMMING - 1 REMOTE TO OPERATE 1 BASE STEP 1 Unplug base for 30 seconds, then plug back in. STEP 2 Remove the battery compartment door from the remote control (FIGURE 6). STEP 5 FIGURE 6 Press and hold the LEARN SWITCH on the remote control (FIGURE 6) until the underbed lighting goes off.
Page 11
REMOTE CONTROL PROGRAMMING - 1 OR 2 REMOTES TO OPERATE 2 BASES Note: Make sure both remotes are in “press & hold” mode and both bases are flat before beginning procedure. If using 2 remotes, both remotes must be in the same “press &...
Page 12
REMOTE CONTROL PROGRAMMING - SEPARATING 2 BASES (independent movement) STEP 1 UNPLUG both bases. STEP 2 BASE 1 Place both bases on their sides close to each other. REMOTE CONTROL 1 CAUTION: DUE TO RISK OF INJURY, TWO ADULTS ARE STEP 3 On both bases, remove the male plug of the dual sync BASE 2...
POWER DOWN OPERATION Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in power down device until necessary for use. Note: Power down device uses 9-volt alkaline batteries, which are not included. STEP 1 Unplug base from electrical power supply.
Page 14
POWER DOWN OPERATION STEP 4 Remove batteries from power down device and discard. Note: Batteries are good for only one use. STEP 5 Plug base into electrical power source (FIGURE 17). When power is restored from outage, base is ready to resume normal operation. FIGURE 17...
TROUBLESHOOTING If the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below: SOLUTION SYMPTOM electrical outlet. A grounded, electrical surge protection device is recommended. Test outlet by plugging in another working appliance. Remote control illuminates and appears to be operable, but will not activate base.
ACCESSORIES Contact customer service toll free (800-888-3078) to order accessories listed below. ACCESSORY DESCRIPTION CODE IMAGE Head Board Brackets-TXL 4B8808 4B8809 Push-in Locking Casters (set of 4) 4B1806 Bed Link Kit (connects two bases together) 4B7410 Swing-away Hinges (headboard required for use, 4B1209 cannot be used with bed straps)
1 YEAR, 3 YEAR AND 25 YEAR LIMITED WARRANTY In this warranty: “Adjustable base” means the adjustable bed foundation sold by L&P to the dealer. The “adjustable base” does not include the mattress. “L&P” means Leggett & Platt, Incorporated. “Purchaser” and “You” both mean the consumer who is the original purchaser of this adjustable base made by L&P.
Page 18
1 YEAR, 3 YEAR AND 25 YEAR LIMITED WARRANTY Repair or replacement shall be the sole remedy of the L&P makes no other warranty whatever, express or Purchaser. There shall be no liability on the part of L&P implied, and all implied warranties of merchantability and for any special, indirect, incidental, or consequential fitness for a particular purpose are disclaimed by L&P and damages or for any other damage, claim, or loss not...
Need help?
Do you have a question about the Prodigy 2.0+ Lumbar and is the answer not in the manual?
Questions and answers
For L&P prodigy2. The lumbar (pillow) moves only one way. The polarity in the OKIN control box doesn’t change.
If the lumbar pillow on a Leggett & Platt Prodigy 2 only moves one way and the polarity in the OKIN control box does not change, the issue could be a malfunction in the control box that prevents it from reversing the motor polarity. This would stop the lumbar motor from moving in both directions.
This answer is automatically generated