red lion PAX Series Manual page 20

SETPOINT SELECTIONS
The following selections are accessible only with the Setpoint plug-in card
installed. Refer to the Setpoint Card Bulletin shipped with the Setpoint plug-in
card for an explanation of their operation.

-
,A:6 Select main or alternate setpoints
#83 -
Reset Setpoint 1 (Alarm 1)
Setpoint -
#8/ Reset Setpoint 2 (Alarm 2)

#80 -
Reset Setpoint 3 (Alarm 3)
Card
-
#8H Reset Setpoint 4 (Alarm 4)
Only
#80H -
Reset Setpoint 3 & 4 (Alarm 3 & 4)

-
#8/0H
Reset Setpoint 2, 3 & 4 (Alarm 2, 3 & 4)
#8",, -
Reset Setpoint All (Alarm All)
5.3 MODULE 3 - D
Module 3 is the programming for Display lock-out and "Full" and "Quick"
Program lock-out.
When in the Display Mode, the available displays can be read consecutively
by repeatedly pressing the DSP key. An annunciator indicates the display being
shown. These displays can be locked from being visible. It is recommended that
,)(
the display be set to when the corresponding function is not used.
SELECTION DESCRIPTION
#&?
Visible in Display Mode
,)( Not visible in Display Mode
"Full" Programming Mode permits all parameters to be viewed and
modified. This Programming Mode can be locked with a security code and/or
user input. When locked and the PAR key is pressed, the meter enters a Quick
Programming Mode. In this mode, the setpoint values can still be read and/or
changed per the selections below. The Display Intensity Level (?8,&G)
parameter also appears whenever Quick Programming Mode is enabled and the
security code is greater than zero.
SELECTION DESCRIPTION
#&?
Visible but not changeable in Quick Programming Mode
&$6
Visible and changeable in Quick Programming Mode
,)( Not visible in Quick Programming Mode
*
Factory Setting can be used without affecting basic start-up.
PROGRAMMING MODE ACCESS
SECURITY USER INPUT USER INPUT
CODE CONFIGURED STATE
+,)(
0 not ————
+,)(
>0 not ————
>0 +,)( Active
>0 +,)( Not Active
0 +,)( Active
0 +,)( Not Active
Throughout this document, Programming Mode (without Quick in front) always refers to "Full" Programming (all meter parameters are accessible).
ISPLAY AND
P
ARAMETERS
PARAMETER MENU
WHEN PAR KEY IS
PRESSED
"Full" Programming
Quick Programming w/Display Intensity
Quick Programming w/Display Intensity
"Full" Programming
Quick Programming
"Full" Programming
PRINT REQUEST
#
*:#83
"
+#I;6
The meter issues a block print through the serial port when activated. The
data transmitted during a print request is programmed in Module 7. If the user
input is still active after the transmission is complete (about 100 msec), an
additional transmission occurs. As long as the user input is held active,
continuous transmissions occur.
P L
ROGRAM OCK
(
4"#*3
MAXIMUM DISPLAY LOCK-OUT*
MINIMUM DISPLAY LOCK-OUT*
TOTALIZER DISPLAY LOCK-OUT*
#
FA
"
,)(
These displays can be programmed for
,)(
, the display will not be shown when the DSP key is pressed regardless of
Program Lock-out status. It is suggested to lock-out the display if it is not needed.
The associated function will continue to operate even if its display is locked-out.
SP-1 SP-2 SP-3 SP-4 SETPOINT ACCESS*
#
:+83
:+8/
" "
,)(
The setpoint displays can be programmed for
following table). Accessible only with the Setpoint plug-in card installed.
PROGRAM MODE SECURITY CODE*
#
(5?&
- to
"
-
By entering any non-zero value, the prompt
to access the Program Mode. Access will only be allowed after entering a
matching security code or universal code of
would not have to be configured for Program Lock-out. However, this lock-out
is overridden by an inactive user input configured for Program Lock-out.
"FULL" PROGRAMMING MODE ACCESS
Immediate access.
After Quick Programming with correct code # at
After Quick Programming with correct code # at
Immediate access.
No access
Immediate access.
19
"
-
OUT
)
#
,)
" "
,)(
,)( #&?
or . When programmed for
# #
:+80
:+8H
"
"
,)( ,)(
,)( #&?
, or
/!-
(5?& -
will appear when trying
///
. With this lock-out, a user input
()?& prompt.
()?& prompt.
#
>3
+#I;6
#
6)6
,)(
#
,)(
&$6
(See the