Rear disc mower with central suspension (48 pages)
Summary of Contents for SaMASZ KDT180
Page 1
(+48) (85) 664 70 41 e-mail: samasz@samasz.pl www.samasz.pl OPERATOR’S MANUAL 1st EDITION 11/2006 REAR DISC MOWER KDT180 - 1,8 m KDT220 - 2,2 m KDT260 - 2,6 m KDT300 - 3,0 m KDT340 - 3,4 m From serial number: 00001...
Page 2
RECOMMENDED MOWER′S ZALECANE POCHYLENIE WORKING KOSIARKI W POZYCJI POSITION ROBOCZEJ IT IS ALLOWED TO WORK IN HORIZONTAL Dopuszcza się pracę w pozycji poziomej. DOPUSZCZA SIĘ PRACĘ W POZYCJI POZIOMEJ POSITION TOO. OTHER POSITION CAN Pochylenie odwrotne powoduje trwałe POCHYLENIE ODWROTNE POWODUJE TRWAŁE DAMAGE THE CUTTERBAR uszkodzenie listwy roboczej.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 We congratulate you on the purchase of your new SaMASZ mower and wish you much pleasure and the very best work results through the years to come. 1. INTRODUCTION General information Operator’s manual is attached to every machine in order that the operator can familiarize himself with design, working principles, service and adjustment of the mower.
- drive unit (3), - safety curtain (6). 2.3 Proper use SaMASZ rear disc mower is designed for mowing standing grass in meadows and in stone free fields. It is a machine for hay and green fodder production. - 4 -...
Optional extra equipment: warning plates with combined lights and reflectors, warning triangle, PTO shaft with overrunning clutch. PTO shafts of other brands with equivalent parameters could be used after SaMASZ permission. Tab.2 PTO shafts for rear disc mowers. Mower Power Length Moment...
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 Fig.3. PTO shaft. PTO shaft lubrication points. Lubricate the PTO shaft with high quality multi-purpose grease every 8 shaft operating hours as shown in fig. 3. If access holes are available, lubricate fittings through access holes. E-kits need lubrication every 50 hours.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 Any maintenance and adjustment work should only be done after the drive has been disconnected and when the cutting discs have come to a complete standstill. Always check mower before starting work, in particular for damaged, missing and/or worn knives and knife holders.
Page 9
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 Caution – read the Caution – while making Operating is forbidden when operator’s manual repairs the machine must any person is within the before putting the be stopped! danger area of 50 m!
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 3.3.Design and operation of safety breakaway device. In the event of hitting an immovable obstacle one of the safety device flat bars slides out and disconnects the safety device. After that the mower folds back about 34 degrees (Fig.5). The operator has time to shut off the tractor and protect the mower.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 Fig. 6. Connecting the mower to the tractor. Fig.7 a) 1 - pin, 2 - bush, 3 - hole in the bar b) Z - lock. CAUTION: Before disconnecting the mower put the pin 1 (fig.7a) into the hole 3 in the bar (fig.7a) to secure the linkage against falling.
Fig. 8. Shut-off valve position: a) open(work), b) closed(transport). about 50cm Fig. 9. SaMASZ rear disc mower in its transport position. 4.3.Preparing the mower for transport on public roads. To meet safety precautions concerning transport on the public roads in Poland the mower...
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 CAUTION: The warning devices can be ordered from the mower manufacturer. warning triangle which can be put into holder on top mower guard. 4.4.Preparing the mower for work. open the shut-off valve on the hydraulic cylinder (fig. 8a.), lower the mower until the cutterbar is at least 50 cm above the ground (fig.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 4.5.Mounting PTO shaft The mowers are driven by Weasler PTO shafts (Tab. 3 page 5). When connecting PTO shaft between tractor and mower make sure, that external guard tube of the shaft is on the tracor’s side.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 Replacing the knives 5.2. Worn and/or damaged knives should be immediately replaced. Replace knives, if necessary, only in sets. Make sure all knives in a set are of the same length and weight. The knife holders must not be damaged or deformed. If the knife holder pin is worn too much, please replace it immediately.
Disc with the forming drum Disc without the forming drum Fig. 13. Swath widths of SaMASZ disc mowers By combining discs and forming drums, different swath widths can be reached. 5.4. Adjusting the cutting height By means of upper link S (fig.6) adjust the cutting height.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 5.5. 3-point linkage support chain. ~40cm Fig. 15. 3-point linkage support chain. Support chain is used to ensure 3-point linkage frame of the mower is always at the same height, to set the mowing unit parallel to the ground and to relieve the hydraulic lift of the tractor.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 5.5.2. Checking the V-belts tension Check the V-belt tension. V-belts are tensioned with spring tensioner (fig. 17) equipped with checking plate. Distance S between plate tip and holder should be 5 mm. If the gap is wider the V-belts will be looser.
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 6.2. Bearings and joints Every 100 mower working hours lubricate PTO shaft bearings and main joints of the mower (Fig.20, 21.). Recommended grease: LT43 (or other designed to lubricate rolling and slide bearings, that work in -30...
Rear disc mower Operator’s manual KDT180;KDT220;KDT260;KDT300; KDT340 7. DEFECTS AND THEIR REPAIRS. Defect Reason Repair Worn knives Replace knives Put on knives strictly acc. to Improperly mounted knives instructions. Reduce PTO Too high PTO rpm rpm(recommended 1800- 2000 rpm) Mower stops working or leaves Too low spring tension –...
Before disassembly the mower should be disconnected from the tractor. 9. WARRANTY CARD Rear disc mower Type of mower Polish Id.No. KTM Polish Id.No. PKWiU KDT180 (1,80 m) KDT220 (2,20 m) KDT260 (2,60 m) KDT300 (3,00 m) KDT340 (3,40 m) Serial number Date of manufacture Manufacturer’s stamp...
2. The warranty period is for a year from the date of sale to the purchaser, stated above. 3. Any repair which is subject to warranty should be carried out by an authorised SaMASZ dealer. Upon completion of the repair the dealer must submit a warranty claim within 21 days.
Rear disc mower KDT180;KDT220;KDT260;KDT300; Operator’s manual KDT340 CAUTION: When the warranty expires, repairs can be done for a payment by the entitled repair shops pointed by the dealer. The dealer is obliged to indicate them. CAUTION: The manufacturer reserves the right to alter technical design and specification without prior notice and without liability.