Table of Contents
Advertisement
This gas appliance should be installed by a qualified
installer in accordance with local building codes and with
current CSA-B149.1 Installation codes for Gas Burning
Appliances and Equipment. If the unit is being installed in
a mobile home, the installation should comply with the
current CAN/ CSA Z240.4 code. For U.S.A. Installations
follow local codes and/ or the current National Fuel Gas
Code, ANSI Z223.1/NFPA 54.
FOR SAFE INSTALLATION AND OPERATION, NOTE
THE FOLLOWING:
1.
This fireplace gives off high temperatures and should
be located out of high traffic areas and away from
furniture and draperies.
2.
Children and adults should be alerted to the hazards
of the high surface temperatures of this fireplace and
should stay away to avoid burns or ignition of clothing.
3.
Children should be carefully supervised when in the
same room as your fireplace.
4.
Under no circumstances should this fireplace be
modified. Parts removed for servicing should be
replaced prior to operating this fireplace again.
5.
Installation and any repairs to this fireplace must be
performed by a qualified installer, service agency or
gas supplier. A professional service person should be
contacted to inspect this fireplace annually. Make it a
practice to have all of your gas fireplaces checked
annually. More frequent cleaning may be required due
to excess lint and dust from carpeting, bedding
material, etc.
6.
Control compartments, burners and air passages in
this fireplace should be kept clean and free of dust
and lint. Make sure the gas valve and pilot light are
turned off before you attempt to clean this fireplace.
7.
The venting system (chimney) of this fireplace should
be checked at least once a year and if needed your
venting system should be cleaned.
8.
Keep the area around your fireplace clear of
combustible materials, gasoline and other flammable
vapor and liquids. This fireplace should not be used
as a drying rack for clothing, nor should Christmas
stockings or decorations be hung in the area of it.
9.
Under no circumstances should any solid fuels (wood,
coal, paper or cardboard etc.) be used in this fire-
place.
10. The flow of combustion and ventilation air must not be
obstructed in any way.
11. When fireplace is installed directly on carpeting, vinyl
tile or any combustible material other than wood, this
fireplace must be installed on a metal or wood panel
extending the full width and depth of the fireplace.
12. This fireplace requires adequate ventilation and
combustion air to operate properly.
13. This fireplace must not be connected to a chimney
flue serving a separate solid fuel burning fireplace.
14. When the fireplace is not in use it is recommended
that the gas valve be left in the "OFF" position.
10002428
Vermont Castings, Majestic Products DVRT36/ 39/ 43
Installation & Operating Instructions
Proposition 65 Warning: Fuels used in gas, wood-
burning or oil fired appliances, and the products of
combustion of such fuels, contain chemicals known to
the State of California to cause cancer, birth defects and
other reproductive harm.
California Health & Safety Code Sec. 25249.6
This appliance may be installed in an aftermarket
permanently located, manufactured home or mobile home,
where not prohibited by local codes.
This appliance is only for use with the type of gas indi-
cated on the rating plate. This appliance is not convertible
for use with other gases, unless a certified kit is used.
The DVRT36RMH has been approved for mobile home
installations.
IMPORTANT:
PLEASE REVIEW THE FOLLOWING CAREFULLY
Remove any plastic from trim parts before turning the
fireplace "ON".
It is normal for fireplaces fabricated of steel to give off
some expansion and/or contraction noises during the
start up or cool down cycle. Similar noises are found with
your furnace heat exchanger or car engine.
It is not unusual for your Vermont Castings, Majestic
Products gas fireplace to give off some odor the first time
it is burned. This is due to the curing of the paint and any
undetected oil from the manufacturing process.
Please ensure that your room is well ventilated - open
all windows.
It is recommended that you burn your fireplace for at
least ten (10) hours the first time you use it. If the optional
fan kit has been installed, place the fan switch in the
"OFF" position during this time.
Locating the Fireplace
E
Y
D
Y
F
Fig. 1 Locating the Gas Fireplace.
A) Flat on wall
B) Cross corner
/
D) Room divider
*
**
E) Flat on wall corner* F) Chase installation
N
otes (Fig. 1):
* When you install your Vermont Castings, Majestic Products fireplace in
(D) Room divider or (E) Flat on wall corner positions, a minimum of (Y),
6 in. (153 mm) clearance must be maintained from the perpendicular
wall and the front of the fireplace.
** Island (C) and Room Divider (D) installation is possible if the horizontal
portion of the vent system (X) does not exceed 20 ft. (610 cm). See
details in Venting Section.
A
B
X
C
B
**
C) Island
Y) 6 in. minimum
LU584-1
3
Hide quick links:
Advertisement
Table of Contents
