Download Table of Contents Print this page

Fujitsu YOKOGAWA AF220 Application Note

Flash programmer - f2mc-16lx family 16-bit microcontroller all series

Advertisement

Quick Links

Fujitsu Microelectronics Europe
MCU-AN-390087-E-V10
Application Note
F²MC-16LX FAMILY
16-BIT MICROCONTROLLER
ALL SERIES
FLASH PROGRAMMER
YOKOGAWA AF220/221
APPLICATION NOTE

Advertisement

Table of Contents
loading

Summary of Contents for Fujitsu YOKOGAWA AF220

  • Page 1 Fujitsu Microelectronics Europe MCU-AN-390087-E-V10 Application Note F²MC-16LX FAMILY 16-BIT MICROCONTROLLER ALL SERIES FLASH PROGRAMMER YOKOGAWA AF220/221 APPLICATION NOTE...
  • Page 2: Revision History

    FLASH PROGRAMMER YOKOGAWA AF220/221 Revision History 1 Revision History Date Issue 23.04.2003 V1.0, HW, First Release This document contains 24 pages. MCU-AN-390087-E-V10 - 2 - © Fujitsu Microelectronics Europe GmbH...
  • Page 3: Warranty And Disclaimer

    Product or parts thereof, if the Product is returned to Fujitsu Microelectronics Europe GmbH in original packing and without further defects resulting from the customer´s use or the transport.
  • Page 4: Table Of Contents

    FLASH PROGRAMMER YOKOGAWA AF220/221 Contents 3 Contents 1 REVISION HISTORY ....................... 2 2 WARRANTY AND DISCLAIMER..................3 3 CONTENTS........................4 4 INTRODUCTION......................6 Programmer overview ..................... 6 System overview ..................... 7 Serial Interface Cable....................8 4.3.1 AZ221......................8 4.3.2 AZ222......................8 Target Probe ......................
  • Page 5 FLASH PROGRAMMER YOKOGAWA AF220/221 Contents 13 APPENDIX ........................23 13.1 Time Measurement ....................23 14 REMARKS ........................24 © Fujitsu Microelectronics Europe GmbH - 5 - MCU-AN-390087-E-V10...
  • Page 6: Introduction

    The programmer allows in-circuit programming of Fujitsu microcontrollers using the serial- synchronous interface. The Yokogawa AF220/AF221 can be adapted to different target controller types by changing the control-module (PC-card). With the FF201 module near all Fujitsu microcontrollers of the 16LX-series can be programmed. The FF205 module supports the MB91F150- family (32-Bit), the FF206 module has to be used together with MB91F360-family (32- Bit).
  • Page 7: System Overview

    • Flash Programmer AF220/221 • Control Module FF201 for Fujitsu 16LX-series • Interface cable AZ210 or AZ211 or AZ212 (see chapter “Target Probe” below) Figure 1-2: Stand-alone Programmer In case that the programmer wants to be controlled by a PC then additionally the •...
  • Page 8: Serial Interface Cable

    FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.3 Serial Interface Cable Two serial interface cables are available. 4.3.1 AZ221 If the COM-port of the host PC uses a 9-pin D-Sub connector then interface cable AZ221 has to be used. Figure 1-5: Serial interface cable AZ221 4.3.2 AZ222...
  • Page 9: Target Probe

    FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.4 Target Probe The AF220/221 Flash Programmer uses a rare connector for connection to the target board: DX31A-28P/DX-28-CV from Hirose Electric (www.hirose.com) Figure 1-8: Pin Layout of Target Probe Figure 1-7: Pin Layout of Connector viewed from cable side Target Probe Connector Yokogawa offers optional three types of Probe Cables (Interface Cable).
  • Page 10: External Key Entry Interface Cable Az223

    FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.5 External Key Entry Interface Cable AZ223 Optional two buttons can be connected externally to EXT.KEY in order to start a command sequence (see chapter 9). Figure 1-12: Pin Layout of Connector EXT.KEY Pin 2...
  • Page 11: Pass/Error Adapter Az266

    FLASH PROGRAMMER YOKOGAWA AF220/221 Introduction 4.6 Pass/Error Adapter AZ266 This optional adapter uses the signal output from EXT.KEY to give the result of programming (PASS / ERROR). It can be used to drive lamps or buzzer in e.g. a manufacture line.
  • Page 12: Hardware Set-Up

    This chapter describes how to set up the programmer 5.1 Hardware Configuration The right PC-card (for Fujitsu 16LX-series: FF201) has to be inserted in the card slot of the programmer. Of course, the power connection with the external power-adapter and the connection to the target board via the interface cable have to be done, too.
  • Page 13: Connection To The Target Board

    FLASH PROGRAMMER YOKOGAWA AF220/221 Hardware Set-up 5.1.2 Connection to the Target Board All devices of the Fujitsu 16LX-series use at least eight signal lines for serial programming: • SINx, SOTx and SCKx for serial communication • MD0, MD2, P00, P01 for Mode-setting •...
  • Page 14: Stand-Alone Operation

    FLASH PROGRAMMER YOKOGAWA AF220/221 Stand-alone operation 6 Stand-alone operation This chapter describes the Yokogawa Flash-Programmer in stand-alone mode The Yokogawa Flash-programmer can be used as stand-alone programmer. In this case, the programmer can be controlled by the integrated keypad. The basic functions are listed below.
  • Page 15: Software - Remote Controller Az290

    FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7 Software – Remote Controller AZ290 This chapter describes how to remote control the Yokogawa Flash-Programmer by a PC The Remote Software Package AZ290 allows to set-up and to control the Flash-Programmer by a PC.
  • Page 16: Basic Operation

    FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7.3 Basic Operation The basic functions for file handling (load, save, purge, etc.) on the PC-card and for programming a device are available in the tab “Basic Operations”. 7.3.1 File Operation Within the Group “File Operation”...
  • Page 17: Device Function

    FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller AZ290 7.3.2 Device Function The basic functions for programming a device are available in the tab “Basic Operations”: ERASE erases the flash-memory and performs blank check BLANK checks whether the memory is cleared PROGRAM programs the flash-memory with the data of the buffer;...
  • Page 18: Software - Remote Controller Library Az291

    FLASH PROGRAMMER YOKOGAWA AF220/221 Software – Remote Controller Library AZ291 8 Software – Remote Controller Library AZ291 This chapter lists the software library functions for programming own applications A software package AZ291 is available to program own front-end applications. The library functions are based on Visual Basic 5.0.
  • Page 19: External Key Entry Interface Az233

    FLASH PROGRAMMER YOKOGAWA AF220/221 External Key Entry Interface AZ233 9 External Key Entry Interface AZ233 This chapter describes how to use two external buttons to control the Flash-Programmer In order to integrate the Yokogawa Flash-Programmer in an automatic assembly line, two external switch-buttons or relays connected to EXT.KEX can be used to start a command...
  • Page 20: Pass/Error Adapter Az266

    FLASH PROGRAMMER YOKOGAWA AF220/221 Pass/Error Adapter AZ266 10 Pass/Error Adapter AZ266 This chapter describes how to output the programming result For extended functionality within an assembly line, the Pass/Error adapter AZ266 (see chapter 4.6) may be helpful to output the result of programming.
  • Page 21: Part List

    FF201 Control Module for Fujitsu 16LX microcontroller FF205 Control Module for Fujitsu microcontroller 91F154, 91F155 FF206 Control Module for Fujitsu microcontroller 91F362GA (asynchronous mode) AZ221 PC cable (D-SUB 9pin – D-SUB 9pin) AZ222 PC cable (D-SUB 9pin – D-SUB 25pin)
  • Page 22: Contact Addresses

    FLASH PROGRAMMER YOKOGAWA AF220/221 Contact Addresses 12 Contact Addresses 12.1 Hitex Development Tools GmbH Mr. Roland Helbig Director Marketing & Sales Greschbachstr. 12 76229 Karlsruhe GERMANY Phone: +49-(0)721 9628 - 134 Fax: +49-(0)721 9628 - 149 E-mail: RHelbig@hitex.de http://www.hitex.de 12.2 AK Elektronik Vertriebs GmbH Mr.
  • Page 23 FLASH PROGRAMMER YOKOGAWA AF220/221 Appendix 13 Appendix 13.1 Time Measurement Based on a MB90F394 with 384KByte Flash the following execution time was measured: Command Time Remark ERASE 9 sec called by One Action key (CSB-file) BLANK CHECK 4 sec called by One Action key (CSB-file) ERASE (incl.
  • Page 24 FLASH PROGRAMMER YOKOGAWA AF220/221 Remarks 14 Remarks MCU-AN-390087-E-V10 - 24 - © Fujitsu Microelectronics Europe GmbH...

This manual is also suitable for:

Yokogawa af221

Table of Contents