Related Manuals for Fujitsu D3003-S
Summary of Contents for Fujitsu D3003-S
- Page 1 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter How To Assembly advice for Fujitsu Industrial Mainboard D3003-S & DASH-Manageability LAN Card 2907-Adapter Contents Assembly Contact Page 1 of 15 ts.fujitsu.com/mainboards...
- Page 2 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter Assembly To assemble the LAN Card D2907-Adapter into the Fujitsu Industrial Mainboard D3003-S please perform the following steps: IPC Chassis closed Open chassis with kit accessories HDD bracket If you would like to configure the system with a HDD you have to use the HDD bracket.
- Page 3 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter D3003-S Mainboard with cooling unit Please mount the cooling unit with four screws as shown on the picture D3003-S in IPC Chassis Insert the mainboard into the chassis Page 3 of 15...
- Page 4 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter Be aware of the exact fitting of the board within the I/O-shield Mount the Mainboard into the chassis with four screws Page 4 of 15 ts.fujitsu.com/mainboards...
- Page 5 Main memory – optional Push the memory carefully from top onto the mainboard until the clamp click into it form the side mSATA – optional Insert the mSATA card from an oblique angle into the slot Page 5 of 15 ts.fujitsu.com/mainboards...
- Page 6 Take special care for the plasic tips! WLAN module – optional If you want to use the WLAN module, please break out carefully the metal part WLAN module – optional Remove the screw for the WLAN module Page 6 of 15 ts.fujitsu.com/mainboards...
- Page 7 Insert the WLAN module Pay attention that the metal nose clicks into the module WLAN module – optional Connect the WLAN module with the USB cable WLAN module – optional Connect the WLAN USB cable with the mainboard Page 7 of 15 ts.fujitsu.com/mainboards...
- Page 8 WLAN module – optional Fix the plastic cover with two screws HDD – optional HDD bracket If you would like to configure the system with a HDD you have to use the HDD bracket. Page 8 of 15 ts.fujitsu.com/mainboards...
- Page 9 The HDD can be fixed with four screws at the bottom site of the bracket. HDD – optional Slide the HDD bracket into the mounting form HDD – optional Fix the HDD bracket to the mounting form with a screw Page 9 of 15 ts.fujitsu.com/mainboards...
- Page 10 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter HDD – optional Connect the HDD with the mainboard HDD – optional Connect the HDD with the mainboard Page 10 of 15 ts.fujitsu.com/mainboards...
- Page 11 HDD and WLAN module D2907 LAN Card – optional Fix the bracket to the LAN card with two screws D2907 LAN Card – optional Connect the USB cable to the LAN card Page 11 of 15 ts.fujitsu.com/mainboards...
- Page 12 Slide the LAN Card from the side into the riser card and fix it with a screw. To fix the riser card in this position, add the crossing strut. Use one screw to mount the strut from the rear side. Page 12 of 15 ts.fujitsu.com/mainboards...
- Page 13 Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter Pay attention to the right fitting. Close the IPC Chassis AC-plug fixture At the rear side of the chassis it is possible to fix the AC-plug with a fortification if necessary. Page 13 of 15 ts.fujitsu.com/mainboards...
- Page 14 How To Assembly advice for D2907 PCI Express Gigabit Ethernet Adapter Chassis mounting / foot assembly Mount the Chassis with three screws Connect with the LAN cable Page 14 of 15 ts.fujitsu.com/mainboards...
-
Page 15: General Information
Copyright 2010 [Fujitsu company name] Fujitsu, the Fujitsu logo, [other Fujitsu trademarks /registered FUJITSU [Company Name] trademarks] are trademarks or registered trademarks of Fujitsu Limited in Japan and other countries. Other Address: x-xx-x, street, city, state, ZIP code, country company, product and service names may be trademarks or registered trademarks of their respective owners.