Subscribe to Our Youtube Channel
Related Manuals for ELECTROCOMPANIET ECI 6DX
Summary of Contents for ELECTROCOMPANIET ECI 6DX
- Page 1 ECI 6DX High Performance ECI 6DX Balanced Integrated Amplifier with built-in DAC and next-gen streamer Owner's Manual Rev 2.0...
- Page 2 Welcome to the world of Electrocompaniet! We thank you for choosing an Electrocompaniet high-end product. At Electrocompaniet we are relentlessly focused on developing audio equipment that is capable of bringing the fabulous experience of the concert hall into the very heart of your home.
- Page 3 • 2 pcs. Batteries. Set up procedure Before connecting the ECI 6DX to the AC Power outlet, check that the main voltage indi- cated on the rear panel corresponds to the line voltage in the country where you intend to use the unit.
-
Page 4: Preamp Out
HT (Home Theatre) HT is a direct input where the volume control is bypassed. ECI 6DX will work like a power amplifier with fixed gain. When selected the output will be muted for a few sec- onds as a safety against accidental overload. -
Page 5: Trigger Input/Output
12V trigger output. The ECI 6DX will power up (leave standby) when a voltage in range 8-20V (AC or DC) is present on the 12V trigger input, and stays powered on for as long as the volt- age is present. -
Page 6: First Time Setup
Setup FIRST TIME SETUP Your ECI 6 DX is equipped with a setup guide through the App that quickly configures the most common settings. In order to access this guide, the ECI 6 DX should be connected to your network by ethernet cable. (not included) If you don’t have access to a router or can’t connect the system using an Ethernet cable, please go to page10 to set up the system wirelessly.”... - Page 7 Setup INITIAL SETUP PROCEDURE WITH A CABLE CONNECTION The first time you set up your ECI 6DX R E C O M M E N D E D Download the “EC PLAY” App The free App is available at Apple store or Google Play.
-
Page 8: Follow The On-Screen Instructions
R E C O M M E N D E D Start your “EC PLAY” App Use a web browser Enter the address of your ECI 6DX in the As long as you have downloaded the App following the previous instructions, web browser. -
Page 9: Enabling Wireless Connection
6. Enter your password, tap “Join” or “OK” 7. Remove the LAN cable and wait until the Rooms button appear. Tap Room and reselect your ECI 6DX If you loose connection with the system, reconnect the network cable and check your network password carefully. - Page 10 Setup PERFORMING THE INITIAL SETUP WIRELESSLY The first time you set up your ECI 6DX. If you can’t perform the setup via ethernet cable (recommended). Then please follow the steps below. Otherwise, please skip this page. R E C O M M E N D E D Download the “EC PLAY”...
-
Page 11: Navigator Window
ECI 6DX by press and hold the Mute button on the remote control (see page 13). If the ECI 6DX has been switched off, allow two hours of warm- up for optimal sonic performance. When the ECI 6DX is not to be used for a long period of time, use the main switch to turn the unit off. -
Page 12: Input Configurations
RCA to XLR adapter: 1 & 3; ground and negative = shorted 2 = positive Updating the ECI 6DX firmware When connected to the internet, the ECI 6DX will automatically download and install the latest firmware. For release notes and further information, please refer to our website, in the “Firmware... -
Page 13: Error Codes
ERROR CODES If the ECI 6DX is not working properly, the display will show an error code. The error codes are: Display Error Description What to do text DC FAULT LEFT DC voltage left channel Please contact service center. DC FAULT... -
Page 14: Tips And Troubleshooting
Connecting to WiFi We recommend that the ECI 6DX has a link quality of minimum 70%, and better than 40 Mb/s link speed. This can be verified in our App, in the More -> Network menu. Higher link quality and speed is recommended for a better user experience. -
Page 15: Preamplifier Section
Technical specifications ECI 6DX: The following technical data were measured on randomized test objects and are typical data. All measurements are made at 120V / 240V // 50Hz / 60Hz. Clipping point of the amplifier is set to a level where total harmonic distortion (THD) is 0.2 %. - Page 16 ECI 6DX Front panel illustration...
- Page 17 ECI 6DX Rear panel illustration...
-
Page 18: Remote Control
When using the remote control, the front end of the remote control should be pointed to the front panel of your ECI 6DX. A free line of sight is required between the remote and the infrared sensor on the front panel. - Page 19 How to connect the system (Analog Inputs)
- Page 20 How to connect the system (Digital Inputs)
-
Page 21: Ir Remote Control Codes
IR Remote control codes RC5 codes are denoted as xx.yy where xx is 5 bit adress and yy is 6 bit command/ data. All numbers are in decimal. RC6 codes are denoted as xxx.yyy. xxx is 8 bit adress. yyy is 8 bit command code. All numbers in decimal. All RC6 codes are mode 0. Key label Code Code... -
Page 22: If Service Is Needed
User Manual Updates Online An updated version of the User Manual may be available online at the Electrocompaniet web site. Occasional updates are needed to reflect new features added to the player since the user Manual was printed. - Page 24 Verify line voltage before use. Do not remove cover. No user serviceable parts inside. Refer servicing to qualified service personal. The warranty is void if the product is tampered by non-authorised personnel.Use only authorized Electrocompaniet service center. Rev.2.0 2020 Made in Norway...
Need help?
Do you have a question about the ECI 6DX and is the answer not in the manual?
Questions and answers