Related Manuals for Atlas Copco PHE 3
Summary of Contents for Atlas Copco PHE 3
- Page 2 2 Remove the four housing screws (1). 3 To remove the locking ring (2) (only applicable for PHE 3 X): open the locking ring on the spindle with aid of special pliers (5) (4931 5990 57) and remove it together with the gear housing (3).
- Page 3 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Removing the 1 Place the spindle vertically and briefly hit striker the plunger (1) with a mandril - the striker (2) comes free. 1 Removing the rear thrust bearing (7): Dismantling the...
- Page 4 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Dismantling the 1 Press the following parts from the spindle: spindle – washer (6) (inner parts) – pressure sleeve (5) only applicable – plunger (4) for PHE 3 – brake disk (2) (is pressed in).
- Page 5 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Removing the 1 Remove the locking ring (1). angle drive 2 Remove the angle drive (3) together with the washers (2) and the support ring (4). (If necessary by hitting the gear housing lightly with a plastic hammer.)
- Page 6 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Removing the 1 Unscrew the strain relief (4). electrical parts 2 Remove the following parts: – switch (2) – capacitor (1) – triac (3) – mains cable (5) – field cable (6)
-
Page 7: Maintenance
Use the appropriate maintenance set for each machine: PHE 3: 4931 3568 29 (220-240 V), 4931 3568 37 (110 V) PHE 3 X: 4931 3568 38 (220-240 V), 4931 3568 40 (110 V) Torque Position... - Page 8 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Before assembly submit all relevant parts to an electrical test (see chapter Electrical and Mechanical Electrical test Test Instruction). Lubrication At each maintenance the tool must be lubricated as shown in the lubrication chart. After having dismantled the entire tool remove the used grease completely and replace it by new grease.
- Page 9 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Assembly Note Please additionally secure all screwed connections in metal with screw locking device. Mounting the 1 Fit the centering ledges (3) to the field (2) field (take care of the right position, see illustration).
- Page 10 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Assembling the 1 Connect all cables with the switch as electrical parts shown in illustration resp. wiring diagram. 2 Push the field cables (6) through the handle as shown in illustration.
- Page 11 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Mounting the 1 Fit the motor cover (1) (mind the right motor cover position) and fasten it with the screws (1,8 Nm). Take care that the rubber cap (2) is stuck in the motor cover.
- Page 12 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Mounting the 1 Insert the two disks (3) and the bolt (4) back gear shaft into the cylinder (2). and the cylinder 2 Insert the rolls (6) into the back gear shaft one after the other and fix it with grease.
- Page 13 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Assembling the 1 Mount the disk springs (1) with the spindle bulgings head-on (see Illustration). (mounting the 2 Mount the clutch (the ratchet (2) with outer parts) indentations against the toothing of the spindle wheel (3)).
- Page 14 Repair Instruction No. 175.8/95 PAGE PHE 3, PHE 3X Mounting the 1 Insert the spring (8) and the retaining SDS-plus disk (7). Reception 2 Depress the retaining disk (7) and insert (applicable for the ball (6). PHE 3) 3 Fit the retaining ring (5) and the sliding sleeve (4).
Need help?
Do you have a question about the PHE 3 and is the answer not in the manual?
Questions and answers