Page 1
I N S T A L L A T I O N O A S W A L L - I N T E G R A T E D R 3 5-06-0012 Publication date 2020-02-27...
Page 2
All rights reserved. No part of this document may be reproduced or copied in any form or by any means without written permission from Orbital Systems. The English language version of this document contains the original in- structions. All other language versions are translations of the original instructions.
Installation T A B L E O F C O N T E N T S EU Declaration of Conformity ..................... 1 Safety Instructions ......................2 Safety Messages Description ..................3 Warranty ........................3 Service ......................... 4 Installation Overview ......................5 Product Measurements ....................
The product has undergone mandatory or voluntary certification procedures in order to receive the following certifications: KIWA TG 1503 KIWA K100686/01 IAPMO E10059 IAPMO C-11154 IAPMO W-11301 Signed for and on behalf of Orbital Systems AB Place Date Name Position Malmö...
III incorporated in the fixed ual, or contact Orbital Systems : wiring plant. • If the shower system is damaged The appliance is designed for a fixed connec- •...
WARNING from delivery of the product. Indicates a potentially hazardous sit- uation which, if not avoided, could Orbital Systems warranty does not cover: result in death or serious injury. • Defects arising out of materials or a design CAUTION specified by the Customer, or by any alter- Indicates a potentially hazardous sit- ations carried out without our consent.
Installation SERVICE Orbital Systems and our team of expert staff are available to assist you should you require product advice, experience any problems, need to purchase spare parts or to set up a service visit. Repairs should always be carried out only by Orbital Systems.
Installation I N S T A L L A T I O N O V E R V I E W PRODUCT MEASUREMENTS 575 mm 1266 mm 1266 mm 440 mm 0 mm Ø 75 mm Ø 75 mm 812 mm 145 mm 122 mm OS Head &...
Installation PREREQUISITES FOR INSTALLATION Electrical Supply Voltage and current rating: 220-240 V~ / 50 Hz / 16 A Residual circuit breaker: One per shower required. Having a rated re- sidual tripping current not exceeding 30 mA Mains supply fixed cord: Min.
Installation SHOWER INSTALLATION OVER- VIEW Drain Unit dimen- HxWxD: 192 x 812 x sions: 184 mm Shower Unit Core Connection to Ø75 mm 2. Core Wall Enclosure drain: 3. Control Dial 4. Shower Head 5. Hand Shower 6. Hand Head Diverter 7.
Installation RECYCLING OPTIMISATION SITE SUGGESTION Recommended installation A fully enclosed shower space with floor heating is recommended to optimize recircu- lation rates. INFORMATION VALID FOR ALL SHOWER VARIANTS. Picture displaying OS Head & Hand Shower variant.
Installation I N S T A L L I N G T H E S H O W E R U N I T SENSOR CABLE, FLUSH HOSE AND RECIRCULATION HOSE watch video: https://bit.ly/2QNFVLP Component Overview Install Sensor Cable, Flush Hose and, Re- circulation Hose.
Installation SENSOR LOCK NOTICE Apply lubricant. Connect hoses to the Sensor Lock. Half thread M4 (3 Hex) CAUTION If Sensor Lock is misaligned it can cause issues in further instal- lation steps.
Page 15
Installation Twist the Sensor Lock Unit slightly to in- sert it into the Drain Pipe. Push it all the way in. Half thread M4 (3 Hex) CAUTION Do not overtighten. Tighten Screw until it just reaches the floor of the drain bowl. Rotate until parallel with the floor of the Drain Bowl.
Installation SMART SENSOR UNIT AND SENSOR TANK CAUTION Make sure the Smart Sensor Unit is inserted horisontally. Do not angle the Smart Sensor. Insert Sensor Tank and connect Smart Sensor Unit with Sensor Lock. Make sure Sensor Lock is in Open position. CAUTION Hand tighten cable connectors to avoid damage.
Page 17
Installation CAUTION Make sure Smart Sensor Unit is inserted correctly. The red O-ring should not be visible. Set Sensor Lock to Locked position.
Installation FUNNEL SHOWER UNIT CORE Remove transport plugs before installa- tion. NOTICE Placing the Funnel with the hole ori- ented to the right will cause the Oas system to not recirculate water.
Page 19
Installation CAUTION Heavy equipment. The Oas Core weighs approx. 20 kg. CAUTION Make sure to attach the Safety Wire before tilting the Shower unit. CAUTION Make sure that hoses and cables are not pinched. WARNING Electrical installation should be performed according to local regulations by a licensed electri- cian.
Page 20
Installation M8 Socket Head CAUTION Make sure to have correct align- ment between key and slot in connectors.
Installation AIR GAP TANK CONTROL DIAL Position the Control Dial according to the “Up” marking before assembly.
Page 23
Installation CAUTION Risk of damage to panel door if overtightening. CAUTION Make sure to have correct align- ment between key and slot in connectors. Plastite screw (12 mm)
Installation NEXT STEP Next step depends on Shower variant. CAUTION The shower will not function without executing following steps. Follow steps valid Follow Filter Capsule, Quartz Glass, UV Lamp, and for OS Head Shower steps valid Wifi have to be installed before starting the (Installing the Show- for 3rd par- shower.
Installation I N S T A L L I N G T H E S H O W E R H E A D Component Overview Shower Head Wall Mount 2. Shower Head Arm 3. Shower Head 2 mm It is recommended to cut the Wall box UNI Push with the LK Wall Box Cutter UNI.
Page 27
Installation Shower Head installation completed.
Installation I N S T A L L I N G T H E H A N D S H O W E R INSTALLING THE DIVERTER AND HAND SHOWER Component Overview Diverter Valve House 2. Diverter Wall Plate 3. Diverter knob 4.
Page 30
Installation 18 mm T25 Screw 50 T25 Screw 32 NOTICE Flip this template in case of left side orientation installation. CAUTION Seal drill holes according to local regulations. CAUTION It’s important that the PEX Hoses are pushed in all the way to ‘stop’ before cutting.
Installation NOTICE Use Torx T8 L key tool in kit T8 2.5x8mm Screw INSTALLING THE HAND SHOWER HOLDER Component Overview MC6S M4x8H A2 Hexagon Screw...
Page 32
Installation Hand Shower Cover 2. T25 Screw 50mm (5.5mm) 3. Hand Shower Bracket 4. T25 Screw 32mm (4.8mm) 5. M4x8 Set Screw Hand Shower installation completed. T25 Screw 50 T25 Screw 32 NOTICE Use Torx T8 L key tool in kit Push Hand Shower Cover into position, use Set Screw to lock.
Log out Settings Add Shower WIFI Settings Support Log out Click “Add shower” and follow instructions. Download the Orbital Systems iOS app from Apple app store and create an User account. It is recommended to always use the latest available version.