Related Manuals for Orbital Systems Orbital Shower Basic R3 OS8733-E
Summary of Contents for Orbital Systems Orbital Shower Basic R3 OS8733-E
- Page 1 Technology Installation Orbital Shower Basic R3 (OS8733-E) 5-06-0013 Publication date 2023-09-22...
- Page 2 All rights reserved. No part of this document may be reproduced or copied in any form or by any means without written permission from Orbital Systems. The English language version of this document contains the original instructions. All other language versions are translations of the original instructions.
-
Page 3: Table Of Contents
Table of Contents Thank you for your purchase ....................4 Prerequisites and Approvals ..................4 Warranty ........................... 5 Service ........................5 System Overview ........................6 Installation Overview ......................7 Installation System Requirements ................7 Seal mountings in wet zone ..................8 Install Orbital Shower Unit .................... -
Page 4: Thank You For Your Purchase
Read the Safety Guide before starting the installation or before operating the shower. Thank you for purchasing the Orbital Shower from Orbital Systems. To enjoy the full potential of the shower please read and follow the procedures in this manual. Make sure that you fully understand how to operate this shower and make sure that it is properly maintained in accordance with the instructions given in this manual. -
Page 5: Warranty
For Warranty and Liability for Defects information, please visit Orbital Systems web https://orbital-systems.se/terms-conditions. Service Orbital Systems and our team of expert staff are available to assist you if you require product advice, experience any problems, need to purchase spare parts or to set up a service appointment. -
Page 6: System Overview
System Overview Orbital Shower Basic R3 (OS8733-E) Shower Head (optional) 2. Control Dial 3. Hand Shower Kit (Hand shower, Diverter and Holder) (optional) 4. Shower Unit (RSK 835 91 20) and Wall brackets (RSK 384 95 38) 5. Drain Unit (RSK 711 54 63) and Outlet unit (RSK 711 99 33) Preparation and installation of shower area (including piping, connections, water proof- ing and tiling), installation of wall brackets (4) and drain (5) are included in the Fixture installation manual. -
Page 7: Installation Overview
Installation Overview Installation System Requirements Connectivity Internet connection: Password protected Wi-Fi 2,4 GHz / 5 GHz or Ethernet. The installation kit contains components for either Wi-Fi connection OR Ethernet depending on what has been specified in the shower order. Electrical Supply Residual circuit breaker: One breaker per Shower Core Power supply:... -
Page 8: Seal Mountings In Wet Zone
Seal mountings in wet zone CAUTION For installation in Sweden according to current Industry Rules Safe Water Installation. All mountings in the wet zone must be sealed against the water- proofing layer of the wall or floor. Material for sealing must adhere to the substrate and be water-resistant, mold-resistant and aging-resistant. -
Page 9: Install Orbital Shower Unit
Install Orbital Shower Unit Component Overview Technology kit Core components Orbital Shower Core, 1x 2. Control Dial , 1x (incl fixture 1x, screws 4x) 3. Sensor tank, 1x 4. Clip, 1x 5. Sensor Tank Dock, 1x 6. Sensor Tank Lock, 1x 7. - Page 10 Component Overview Technology kit Shower heads & diverter Hand shower with hose, 1x 2. Head shower arm, 1x 3. Head shower, 1x 4. Diverter knob,1x + set screw, 1x 5. Diverter molded valve house, 1x 6. Diverter wall plate, 1x 7.
-
Page 11: Install Sensor Cable, Flush Hose And Recirculation Hose
Install Sensor Cable, Flush Hose and Recirculation Hose Install Sensor Cable, Flush Hose and Recirculation Hose. Make sure the Sensor Cable goes first and that the connector protection cover is on. NOTICE It is recommended to use fish tape to route the cables through the pipes. Page 11 of 48... - Page 12 4. Pull the Sensor Cable to where 20 cm of slack is visible. Page 12 of 48...
-
Page 13: Install Sensor Tank Dock
Install Sensor Tank Dock NOTICE Apply lubricant according to industry rules. Make sure that the o-rings are lubricated. Connect Hoses to Sensor Tank Dock. Lock Hoses by inserting Clip. Page 13 of 48... - Page 14 Insert Sensor Tank Dock into Connection Pipe. Push it all the way in. 4. Lock Sensor Tank Dock in place with the Spring Lock. Page 14 of 48...
-
Page 15: Install Sensor Tank And Sensor Tank Lock
Install Sensor Tank and Sensor Tank Lock Connect the Sensor Cable to the Sensor Tank. CAUTION Make sure to have correct alignment between key and slot in connectors by aligning the two white lines. Insert Sensor Tank. Page 15 of 48... - Page 16 Lock the Sensor Tank in position with the Sensor Tank Lock by turning it 90 degrees. CAUTION Make sure Sensor Tank is inserted correctly. The edge of the Sensor Tank should be fully pushed towards and in level with the edge of the Drain Unit.
-
Page 17: Install Funnel
Install Funnel NOTICE Place the Funnel with the hole oriented to the left! Placing the hole oriented to the right will disable recirculation. Page 17 of 48... -
Page 18: Install Orbital Shower Core
Install Orbital Shower Core Remove transport plugs before installation. Insert Orbital Shower Core into the Top and Bottom Bracket Assembly. CAUTION • Heavy equipment. Orbital Shower Core weighs approx. 25 kg • Make sure Hoses and Cables do not get pinched. Page 18 of 48... - Page 19 4. Connect the Wifi Antenna Cable. Page 19 of 48...
- Page 20 Page 20 of 48...
- Page 21 CAUTION Make sure to have correct alignment between key and slot in connectors. Make sure locking ring snaps and connector is locked. Page 21 of 48...
- Page 22 Only valid for Orbital Ethernet installation Pull Ethernet cable through the cable connector and attach the RJ45 connector. 10. Hand tighten cable connectors to avoid damage. Page 22 of 48...
- Page 23 11. Only valid for Orbital Audio Installation Connect the amplifier cable to the core. Page 23 of 48...
-
Page 24: Install Hose Connections
Install Hose Connections CAUTION Install Hose Connections according to industry rules. Page 24 of 48... -
Page 25: Add The Filter Capsule
Add the Filter Capsule Page 25 of 48... - Page 26 Insert Filter Capsule. RISK OF LEAKAGE Make sure Filter Capsule is inserted all the way in or leakage may occur. 4. "Click!" Page 26 of 48...
-
Page 27: Install Air Gap Tank Cover
Install Air Gap Tank Cover Attach the Cover to the Air Gap Tank by snapping it onto the magnetic plate. Page 27 of 48... -
Page 28: Install Control Dial
Install Control Dial Cut Conduit flush to tile surface. Level the Fixture and make sure it is centered on the hole of the wall. Page 28 of 48... - Page 29 Drill 4 holes (4,0 mm) in marked locations. Make sure that it is the outer holes in the fixture that is used. CAUTION Only drill through the tile itself, no deeper. CAUTION Seal drill holes according to industry rules. See section Seal mountings in wet zone [8] for instruction.
- Page 30 Connect the Control Dial cable to the extension cord. NOTICE Do not remove the protective cover from the Control Dial until installation is completed. Page 30 of 48...
- Page 31 Pull the Cable through the Conduit. NOTICE It is recommended to use fish tape to route the cables through the pipes. Page 31 of 48...
- Page 32 Position the Control Dial according to the “up marking” before assembly. Page 32 of 48...
- Page 33 11. "Click!" Snap on the Control Dial onto the Fixture. Make sure to align the brackets according to the arrows. CAUTION Make sure to have correct alignment between key and slot in connectors. Make sure locking ring snaps and connector is locked. Page 33 of 48...
- Page 34 Page 34 of 48...
-
Page 35: Next Step
CAUTION The Orbital Shower will not function without executing following steps. Orbital Shower Core installation completed. Next step depends on Shower variant. Follow steps valid for Orbital Systems Follow steps valid for Orbital Systems Shower Head (Installing the Shower Hand Shower... -
Page 36: Installing The Shower Head
Installing the Shower Head Component Overview Shower Head Wall Mount 2. Shower Head Arm 3. Shower Head It is recommended to cut the Wallbox UNI Push with the LK Wall Box Cutter UNI. Page 36 of 48... - Page 37 6-9 mm NOTICE Cover the end of the Shower Water Connector with thread sealant to avoid leakage. Page 37 of 48...
- Page 38 CAUTION Make sure not to cross thread and not to overtighten. Shower Head installation completed. Page 38 of 48...
-
Page 39: Installing The Hand Shower
Installing the Hand Shower Installing the Diverter and Hand Shower Component Overview Diverter Body, x1 2. O-ring, x2 3. Diverter Wall Plate, x1 4. TX25 screw, x2 and Twin Washer, x1 5. Hand Shower, x1 6. Shower Hose, x1 Page 39 of 48... - Page 40 Cut Conduit minimum 6 mm, max 9 mm outside of tile surface. Page 40 of 48...
- Page 41 Mark hole positions for Hand Shower holder as well. 31mm 10mm 300mm 4. Drill 4 holes (6 mm) in marked locations. CAUTION • Only drill through the tile itself. • Seal drill holes according to industry rules. See section Seal mountings in wet zone [8] for instruction.
- Page 42 CAUTION Use 2x included screw, choose screw according to wall thickness. TX25 stainless steel screw Twin washer CAUTION It’s important that the PEX hoses are pushed in all the way to ‘stop’ before cutting to the correct length of 25 mm. CAUTION Make sure the pipe is cut straight and avoid too many degrees.
- Page 43 Use an Allen key, 3mm, to secure the Diverter Body to the Diverter Wall Plate. Page 43 of 48...
-
Page 44: Installing The Hand Shower Holder
Installing the Hand Shower Holder Component Overview Hand Shower Cover 2. T25 stainless steel screw 50 mm (5.5 mm), x2 3. Hand Shower Bracket 4. M4 x 8 set screw Page 44 of 48... - Page 45 T25 stainless steel screw 50 mm (5.5mm) Push Hand Shower Cover into position and use the Set Screw to lock it. NOTICE Use Torx T8 L key tool in kit Page 45 of 48...
- Page 46 Hand Shower installation completed. Page 46 of 48...
-
Page 47: Shower Activation, Wi-Fi Setup And Installation Test
Shower Activation, Wi-Fi Setup and Installation test To set up Wi-Fi and do an installation test on your Orbital Shower, please download My Water by Orbital Systems from App Store or Google Play and follow the instructions provided in the app. Internet Connection is required Password protected Wi-Fi 2,4 GHz / 5 GHz or Ethernet. - Page 48 C E R T I F I E D S P A C E T E C H N O L O G Y...