Summary of Contents for Orbital Systems R3 OS8733-E
Page 1
Technology Installation Orbital Shower Panel R3 (OS8733-E) 5-06-0012 Publication date 2023-09-22...
Page 2
All rights reserved. No part of this document may be reproduced or copied in any form or by any means without written permission from Orbital Systems. The English language version of this document contains the original instructions. All other language versions are translations of the original instructions.
Table of Contents Thank you for your purchase ....................4 Prerequisites and Approvals ..................4 Warranty ........................... 5 Service ........................5 System Overview ........................6 Installation Overview ......................7 Installation System Requirements ................7 Seal mountings in wet zone ..................8 Install Orbital Shower Unit ....................
Read the Safety Guide before starting the installation or before operating the shower. Thank you for purchasing the Orbital Shower from Orbital Systems. To enjoy the full potential of the shower please read and follow the procedures in this manual. Make sure that you fully understand how to operate this shower and make sure that it is properly maintained in accordance with the instructions given in this manual.
For Warranty and Liability for Defects information, please visit Orbital Systems web https://orbital-systems.se/terms-conditions. Service Orbital Systems and our team of expert staff are available to assist you if you require product advice, experience any problems, need to purchase spare parts or to set up a service appointment.
System Overview Orbital Shower Panel R3 (OS8733-E) Shower Head (optional) 2. Control Dial 3. Hand Shower Kit (Hand shower, Diverter and Holder) (optional) 4. Shower Unit (RSK 835 91 20) and Cabinet (RSK 831 41 82) 5. Drain Unit (RSK 711 54 63) and Outlet unit (RSK 711 99 33) Preparation and installation of shower area (including piping, connections, water proof- ing and tiling), installation of cabinet (4) and drain (5) are included in the Fixture installa- tion manual.
Installation Overview Installation System Requirements Connectivity Internet connection: Password protected Wi-Fi 2,4 GHz / 5 GHz or Ethernet. The installation kit contains components for either Wi-Fi connection OR Ethernet depending on what has been specified in the shower order. Electrical Supply Residual circuit breaker: One breaker per Shower Core Power supply:...
Seal mountings in wet zone CAUTION For installation in Sweden according to current Industry Rules Safe Water Installation. All mountings in the wet zone must be sealed against the water- proofing layer of the wall or floor. Material for sealing must adhere to the substrate and be water-resistant, mold-resistant and aging-resistant.
Install Sensor Tank Dock NOTICE Apply lubricant according to industry rules. Make sure that the o-rings are lubricated. Connect Hoses to Sensor Tank Dock. Lock Hoses by inserting Clip. Page 13 of 49...
Page 14
Insert Sensor Tank Dock into Connection Pipe. Push it all the way in. 4. Lock Sensor Tank Dock in place with the Spring Lock. Page 14 of 49...
Install Sensor Tank and Sensor Tank Lock Connect the Sensor Cable to the Sensor Tank. CAUTION Make sure to have correct alignment between key and slot in connectors by aligning the two white lines. Insert Sensor Tank. Page 15 of 49...
Page 16
Lock the Sensor Tank in position with the Sensor Tank Lock by turning it 90 degrees. CAUTION Make sure Sensor Tank is inserted correctly. The edge of the Sensor Tank should be fully pushed towards and in level with the edge of the Drain Unit.
Install Funnel NOTICE Place the Funnel with the hole oriented to the left! Placing the hole oriented to the right will disable recirculation. Page 17 of 49...
Install Orbital Shower Core Remove Transport Plugs before installation. Insert Orbital Shower Core into the Wallbox and attach Safety Wire. Keep tilted to enable electrical installation. CAUTION • Heavy equipment. The Orbital Shower Core weighs approx. 25 kg. • Make sure to attach the Safety Wire before tilting the Orbital Shower Core.
Page 19
WARNING Electrical installation should be performed according to industry rules by a competent electrician. Page 19 of 49...
Page 20
M8 socket head CAUTION Make sure to have correct alignment between key and slot in connectors. Make sure locking ring snaps and connector is locked. Page 20 of 49...
Page 21
Only valid for Orbital Ethernet installation Pull Ethernet cable through the cable connector and attach the RJ45 connector. Make sure the core is not tilted out, keep it in up-right position. Page 21 of 49...
Page 22
Hand tighten cable connectors to avoid damage. 10. Only valid for Orbital Audio Installation Connect the amplifier cable to the core. Page 22 of 49...
Install Hose Connections RSK 188 24 82 Provided by Customer: • Hose Connections, x2 CAUTION • Install Hose Connections according to industry rules. • Make sure to flush out the water lines from debris before connecting the Core. Page 23 of 49...
Page 24
Connect incoming and outgoing water to the core. Page 24 of 49...
Install Control Dial Plastite screw NOTICE Do not remove the protective cover from the Control Dial until installation is completed. Page 29 of 49...
Page 30
Position the Control Dial according to the “up marking” before assembly. Page 30 of 49...
Page 31
"Click!" Snap on the Control Dial onto the Fixture. Make sure to align the brackets according to the arrows. Page 31 of 49...
Page 32
CAUTION Make sure to have correct alignment between key and slot in connectors. Make sure locking ring snaps and connector is locked. Page 32 of 49...
Install Panel Lock NOTICE Clean surface before attaching Bracket. Adjust until edge aligned to edge. Adjust until edge aligned with magnet. Page 33 of 49...
CAUTION The Orbital Shower will not function without executing following steps. Orbital Shower Core installation completed. Next step depends on Shower variant. Follow steps valid for Orbital Systems Follow steps valid for Orbital Systems Shower Head (Installing the Shower Hand Shower...
Installing the Shower Head Component Overview Shower Head Wall Mount 2. Shower Head Arm 3. Shower Head It is recommended to cut the Wallbox UNI Push with the LK Wall Box Cutter UNI. Page 37 of 49...
Page 38
6-9 mm NOTICE Cover the end of the Shower Water Connector with thread sealant to avoid leakage. Page 38 of 49...
Page 39
CAUTION Make sure not to cross thread and not to overtighten. Shower Head installation completed. Page 39 of 49...
Installing the Hand Shower Installing the Diverter and Hand Shower Component Overview Diverter Body, x1 2. O-ring, x2 3. Diverter Wall Plate, x1 4. TX25 screw, x2 and Twin Washer, x1 5. Hand Shower, x1 6. Shower Hose, x1 Page 40 of 49...
Page 41
Cut Conduit minimum 6 mm, max 9 mm outside of tile surface. Page 41 of 49...
Page 42
Mark hole positions for Hand Shower holder as well. 31mm 10mm 80mm 4. Drill 4 holes (6 mm) in marked locations. CAUTION • Only drill through the tile itself. • Seal drill holes according to industry rules. See section Seal mountings in wet zone [8] for instruction.
Page 43
CAUTION Use 2x included screw, choose screw according to wall thickness. TX25 stainless steel screw Twin washer CAUTION It’s important that the PEX hoses are pushed in all the way to ‘stop’ before cutting to the correct length of 25 mm. CAUTION Make sure the pipe is cut straight and avoid too many degrees.
Page 44
Use an Allen key, 3mm, to secure the Diverter Body to the Diverter Wall Plate. Page 44 of 49...
Installing the Hand Shower Holder Component Overview Hand Shower Cover 2. T25 stainless steel screw 50 mm (5.5 mm), x2 3. Hand Shower Bracket 4. M4 x 8 set screw Page 45 of 49...
Page 46
T25 stainless steel screw 50 mm (5.5mm) Push Hand Shower Cover into position and use the Set Screw to lock it. NOTICE Use Torx T8 L key tool in kit Page 46 of 49...
Page 47
Hand Shower installation completed. Page 47 of 49...
Shower Activation, Wi-Fi Setup and Installation test To set up Wi-Fi and do an installation test on your Orbital Shower, please download My Water by Orbital Systems from App Store or Google Play and follow the instructions provided in the app. Internet Connection is required Password protected Wi-Fi 2,4 GHz / 5 GHz or Ethernet.
Page 49
C E R T I F I E D S P A C E T E C H N O L O G Y...