Related Manuals for Keba Kemro FX 271/A
Summary of Contents for Keba Kemro FX 271/A
- Page 1 Kemro FX 271/A, FX 271/B SERCOS III Master Module (Standard-PCI) Project engineering manual V1.07 Translation of the original instructions...
- Page 2 Specifications are subject to change due to further technical developments. Details presented may be subject to correction. All rights reserved. KEBA AG Headquarters: Gewerbepark Urfahr, 4041 Linz, Austria, Phone: +43 732 7090-0, Fax: +43 732 7309-10, keba@keba.com For information about our subsidiaries please look at www.keba.com.
- Page 3 Hint "not for end customers" added, various minor up- fstl dates. 1.06 08-2011 Introduction Hint "not for end customers" added, various minor up- fstl dates. 1.07 01-2015 Several updated, new variant FX 271/B swb, ekr Project engineering manual V1.07 © KEBA 2015...
-
Page 5: Table Of Contents
Reset........................21 Disposal........................... 22 Disposal of the module..................22 10 Technical data......................... 23 10.1 Interface to the CPU module................. 23 10.2 Environmental conditions..................23 10.3 SERCOS III interface.................... 23 10.4 Ethernet interface....................23 Project engineering manual V1.07 © KEBA 2015... - Page 6 11.2.3 Electrical safety and fire protection............24 11.2.4 Environmental and surrounding conditions..........24 11.3 Standards for the American market..............24 11.3.1 UL test for industrial control equipment..........24 12 Declaration of conformity....................25 Project engineering manual V1.07 © KEBA 2015...
-
Page 7: Introduction
Preconditions This document contains information for persons with the following skills: Project engineering manual V1.07 © KEBA 2015... -
Page 8: Notes On This Document
1.4.1 Content of the document ● General information on SERCOS III ● Description of the module FX 271/x ● Description of the configuration ● Technical data Project engineering manual V1.07 © KEBA 2015... -
Page 9: Not Contained In This Document
If you are using the KeStudio U3 tool suite: Doc.No. Name Target group ● Project engineer ● Electrician DE: 1000868 System manual Kemro automation ● Programmer system EN: 1000869 ● Commissioning foreman ● Service technician Project engineering manual V1.07 © KEBA 2015... -
Page 10: Safety Notes
It is absolutely essential to observe the safety instructions in the system manual. ● The module is defined as "open type equipment" (UL508) or as "offenes Betriebsmittel" (EN 61131-2) and must therefore be installed in a control cabinet. Project engineering manual V1.07 © KEBA 2015... - Page 11 When removed from it's casing this module is sensitive to electrostatic dis- charge. Before handling the modules touch a grounded metal object in order to discharge any static electricity from your body. Project engineering manual V1.07 © KEBA 2015...
-
Page 12: Description Of The Module
Variant FX 271/B: CP 24x/x or CP 26x/x Information The module’s functionality is only guaranteed if used within the appropriate mentioned CPU modules. The module is not designed for connection with foreign modules. Front view Fig.3-1: FX 271/x front view Project engineering manual V1.07 © KEBA 2015... -
Page 13: Essential Features Of Sercos Iii
Non-real-time (NRT) channel for transmitting standardized or prioritized IP protocols ● Error tolerance against cable break through media redundancy ● Direct connection of service notebooks to SERCOS III slaves ● Cost-effective and simple networking through the elimination of switches or hubs Project engineering manual V1.07 © KEBA 2015... -
Page 14: Displays And Operating Elements
Ethernet status LEDs The Ethernet-socket (RJ-45) offers a Link-Status-LED and an Activity-LED. Display Significance Link-Status-LED Lights up as soon as an Ethernet connection is available. (green) Activity-LED Lights up when sending and receiving data. Project engineering manual V1.07 © KEBA 2015... -
Page 15: Installation Instructions
CPU modules. The module is not designed for connection with foreign modules. Inserting an option module into slot 1) Turn off power supply 2) Remove dummy module 3) Insert module in the correct position (labelling right side) into the right-hand slot Project engineering manual V1.07 © KEBA 2015... - Page 16 FX 271/A, FX 271/B Fig.5-2: Inserting the FX 271/x Removing an option module 1) Turn off power supply 2) Pull module out of the slot 3) Insert dummy module Fig.5-3: Removing the FX 271/x Project engineering manual V1.07 © KEBA 2015...
-
Page 17: Connections And Wiring
SERCOS III interface sercos III is the third generation sercos interface series according to IEC/EN 61491 based on standard Ethernet IEEE 802.3. 6.1.1 Connection example Fig.6-1: Bus topology SERCOS III in ring structure Project engineering manual V1.07 © KEBA 2015... -
Page 18: Pin Assignment
PIN no. Designation Transmit data+ (pair 1) Transmit data- (pair 1) Transmit data+ (pair 2) n.c. n.c. Receive data- (pair 2) n.c. n.c. 6.1.3 Cable and plug specification Further information: See system manual. Project engineering manual V1.07 © KEBA 2015... -
Page 19: Ethernet Interface
6.2.2 Cable and plug specification Further information: See system manual. EMC and wiring guidelines Pay attention from the outset to careful wiring and shielding. Further information: See system manual. Project engineering manual V1.07 © KEBA 2015... -
Page 20: Configuration
Configuration data is created by included configuration tools or by editing con- figuration files. For further information about the configuration see the documentation of the included configuration tool. Project engineering manual V1.07 © KEBA 2015... -
Page 21: Operating Behavior
Operating behavior Start-up after Power-On The module is passive and is configured and activated through the HOST. Reset The module can be reset by the HOST without the HOST itself having to be reset. Project engineering manual V1.07 © KEBA 2015... -
Page 22: Disposal
● The materials are recyclable in accordance with their labeling. You can make an important contribution to protecting our environment by reusing, renewing and recycling materials and old appliances. Project engineering manual V1.07 © KEBA 2015... -
Page 23: 10 Technical Data
Mechanical properties Structure: No casing; only front plate mounted on print When the module is plugged into the CPU mod- Protection class: ule, the CPU module conforms to IP 20 Weight: 83 g Project engineering manual V1.07 © KEBA 2015... - Page 24 Operation with compact flash card or SSD EN 61131-2:2007 Programmable controllers - Part 2 11.3 Standards for the American market 11.3.1 UL test for industrial control equipment UL 508, 2005 Industrial Control Equipment Project engineering manual V1.07 © KEBA 2015...
- Page 25 We declare that the following product(s) is/are in conformity with the essential requirements of the following European Council Directive(s). Conformity to the directive(s) is/are assured by the compliance with the appli- cable parts of the described harmonized European standards. x ... variant suffix Project engineering manual V1.07 © KEBA 2015...
- Page 26 Important notes: This document is only an overview and not the original declaration of conform- ity. The original declarations of conformity can be requested from KEBA. Any modification on the product(s), that is performed without KEBA’s consent will render this declaration invalid. The safety instructions contained in the documentation supplied with the product(s) must implicitly be followed! Project engineering manual V1.07...