Page 1
H3C LSWM18CQMSEC interface card user manual-6PW106 ▌Introduction Overview The LSWM18CQMSEC interface card provides eight QSFP28 ports. These QSFP28 ports support MACsec. Figure 1 Front panel (1) QSFP28 port LED (2) QSFP28 port QSFP28 ports You can install the following transceiver modules and cables in the QSFP28 ports on the card: •...
Page 2
Table 1 QSFP28 transceiver modules available for the QSFP28 ports (1) QSFP28 transceiver Central wavelength (nm) Connector module Four lanes: • 1294.53~1296.59 QSFP-100G-ER4L- • 1299.02~1301.09 WDM1300 • 1303.54~1305.63 • 1308.09~1310.19 MPO (PC QSFP-100G-SR4- polished, MM850 12-fiber) MPO (APC QSFP-100G-PSM4- 1295~1325 polished, SM1310 12-fiber)
Page 3
Table 2 QSFP28 transceiver modules available for the QSFP28 ports (2) QSFP+ Cable/fiber Modal Max transmission transceiver diameter bandwidth distance module (µm) (MHz × km) QSFP-100G-E Single-mode, 40 km (24.85 R4L-WDM1300 9/125 miles) 2000 70 m (229.66 ft) QSFP-100G-S Multi-mode, R4-MM850 50/125 4700...
Page 4
Table 4 QSFP28 to SFP28 copper cables available for the QSFP28 ports QSFP28 to SFP28 copper cable Cable length Data rate QSFP-100G-4SFP-25G-CAB-1M 1 m (3.28 ft) QSFP-100G-4SFP-25G-CAB-3M 3 m (9.84 ft) 100 Gbps QSFP-100G-4SFP-25G-CAB-5M 5 m (16.40 ft) Table 5 QSFP+ transceiver modules available for the QSFP28 ports (1) Central QSFP+ transceiver module...
Page 5
Table 6 QSFP+ transceiver modules available for the QSFP28 ports (2) QSFP+ Cable/fiber Modal transceiver diameter bandwidth transmission module (µm) (MHz × km) distance 2000 100 m (328.08 ft) QSFP-40G-SR4 Multi-mode, -MM850 50/125 4700 150 m (492.12 ft) 2000 300 m (984.25 ft) QSFP-40G-CS Multi-mode, R4-MM850...
Page 6
LSWM1QSTK5 5 m (16.40 ft) NOTE: • As a best practice, use H3C transceiver modules and cables for the card. • H3C transceiver modules and cables available for the card are subject to change over time. For the most recent list of H3C transceiver modules and cables available for the card, contact H3C Support or marketing staff.
• To avoid device damage, do not use excessive force when you install or remove the card. • The LSWM18CQMSEC interface card is hot swappable. However, do not install or remove it during the startup of the switch.
4. As shown by callout 1 in Figure 3, insert the card slowly into the slot along the guide rails. 5. Rotate inward the ejector lever as shown by callout 2 in Figure 3 until the latch locks the ejector lever in place. Figure 3 Installing the card Removing the card 1.
▌Technical support New H3C Technologies Co., Ltd. provides customers with comprehensive technical support and service. If you purchase the products from the sales agent of New H3C Technologies Co., Ltd., please contact our sales agent or technical personnel. Website: http://www.h3c.com...
Need help?
Do you have a question about the LSWM18CQMSEC and is the answer not in the manual?
Questions and answers