Setting Jumpers - TYAN Trinity ATX Motherboard S1598 User Manual

Chapter 2
Board Installation

1. Setting Jumpers

1-A. CPU Bus Speed Settings
B s u S e p d e
0 6 M H z
6 6 M H z
5 7 M H z
3 8 M H z
5 9 M H z
1 0 0 M H z
1-C. CPU Core Voltage Settings
C P U o V a t l e g
1 3 . V
1 4 . V
1 5 . V
1 6 . V
1 7 . V
1 8 . V
1 9 . V
2 0 . V
2 1 . V
2 2 . V * *
2 3 . V
2 4 . V
** Default Setting (2.2V)
The CPU speed is controlled by setting the bus speed and the multiplier with
the jumpers described above that are appropriate for your CPU and memory.
You must have a 100MHz processor AND PC/100 memory to run at a bus
speed of 100MHz. Tyan does not recommend operating CPUs, memory or PCI
! ! ! ! !
bus at higher than rated speed. Tyan takes no responsibility for any problems
related to overclocking any bus or component on the system board.
important!
J 4 P J 5 P J 6 P
2 3 - 2 3 - 2 3 -
1 2 - 2 3 - 2 3 -
1 2 - 1 2 - 2 3 -
1 2 - 2 3 - 1 2 -
2 3 - 1 2 - 1 2 -
1 2 - 1 2 - 1 2 -
J 8 P J 9 P P J 0 1 P J 1 1
O F F O F F O F F O F F
O F F O N O F F O F F
O F F O F F O N O F F
O F F O N O N O F F
O F F O F F O F F O N
O F F O N O F F O N
O F F O F F O N O N
O F F O N O N O N
O N O F F O F F O F F
O F F O N O F F O F F
O N O N O F F O F F
O F F O F F O N O F F
1-B. CPU Clock Multiplier
M u i t l i l p r e
. 2 x 5
x 3
. 3 x 5
x 4
. 4 x 5
x 5
. 5 x 5
P J 2 1
C P U o V a t l e g
O N
. 2 V 5
O N
. 2 V 6
O N
. 2 V 7
O N
. 2 V 8
O N
. 2 V 9
O N
. 3 V 0
O N
. 3 V 1
O N . 3 V 2
O F F
. 3 V 3
O F F . 3 V 4
O F F . 3 V 5
O F F
14
J 1 P J 2 P J 3 P
O N O N O F F
O F F O N O F F
O F F O F F O F F
O N O F F O N
O N O N O N
O F F O N O N
O F F O F F O N
J 8 P J 9 P P J 0 1 P J 1 1
O N O F F O N O F F
O F F O N O N O F F
O N O N O N O F F
O F F O F F O F F O N
O N O F F O F F O N
O F F O N O F F O N
O N O N O F F O N
O F F O F F O N O N
O N O F F O N O N
O F F O N O N O N
O N O N O N O N
http://www.tyan.com
P J 2 1
O F F
O F F
O F F
O F F
O F F
O F F
O F F
O F F
O F F
O F F
O F F