Swing-N-Slide JAMBOREE Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Swing-N-Slide Manuals
  4. Play Sets & Playground Equipment
  5. JAMBOREE
  6. Assembly instructions manual

Swing-N-Slide JAMBOREE Assembly Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PB 8328
WS 8328
JAMBOREE
IMPORTANT!!
PLEASE READ BEFORE BEGINNING ASSEMBLY!!
Please make sure all lumber, hardware and accessory parts are accounted for.
If you are missing anything, please DO NOT RETURN to the store where purchased.
Please call our Customer Service Department at the number below.
ASSEMBLY INSTRUCTIONS
© Swing-N-Slide
Printed in USA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JAMBOREE and is the answer not in the manual?

Questions and answers

Related Manuals for Swing-N-Slide JAMBOREE

Summary of Contents for Swing-N-Slide JAMBOREE

  • Page 1 PB 8328 WS 8328 JAMBOREE IMPORTANT!! PLEASE READ BEFORE BEGINNING ASSEMBLY!! Please make sure all lumber, hardware and accessory parts are accounted for. If you are missing anything, please DO NOT RETURN to the store where purchased. Please call our Customer Service Department at the number below.
  • Page 5 DIMENSIONS STRUCTURE.
  • Page 6 TOOLS REQUIRED DRILL HAMMER TAPE MEASURE PLIERS PHILLIPS BIT CARPENTER SQUARE INCLUDED HARDWARE Small Square Bit...
  • Page 7 HARDWARE Small...
  • Page 8 SA6066 BOX 1 of 2 BOARD LIST...
  • Page 9 SA6065 BOX 2 of 2 BOARD LIST...
  • Page 10 COMPONENTS...
  • Page 12 STEP 1 Check to make sure Flush structure is square Per Board NOTE HOLES PANEL A Install 30mm Screws With Heads Flushed To Board To Avoid Protrusions. Per Board PANEL B Per Board Flush PANEL C Per Board...
  • Page 13 STEP 2 Per Board Check to make sure structure is square Per Board FLUSH PANEL D Per Board Per Board FLUSH Install 30mm Screws With Heads Flushed To Per Board Board To Avoid FLUSH Protrusions. PANEL E...
  • Page 14 STEP 3 Check to make sure structure is square PANEL C Flush T-Nut Small Flush NOTE HOLES Flush to the bottom NOTE: HOLE ORIENTATION T-Nut Small Flush FRAME A Flush Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
  • Page 15 STEP 4 FRAME A FLIP FRAME OVER...
  • Page 16 STEP 5 T-Nut Small per Board This Side NOTE HOLE Flush per Board NOTE: This Side HOLE ORIENTATION T-Nut Small FRAME B Flush Check to make sure structure is square WINDOW PANE INSTALL Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
  • Page 17 STEP 6 FRAME B FLIP FRAME OVER...
  • Page 18 STEP 7 Flush 3’’ From Outside of Post PANEL A Flush Check to make sure structure is square 3’’ From outside of post To end of horizontal PANEL A support. Flush to Flush outside edge of 3”x 3” PF 6338 Flush to 94-1/4’’...
  • Page 19 STEP 8 FRAME A Flush Flush 3’’ From Outside of Post to End of Horizontal Support. Side View of Tower FRAME B 19-1/2’’...
  • Page 20 STEP 9 Flush per side Back of Tower Flush NOTE: PRE-DRILL HOLES GOING INTO DECK SUPPORTS per side 55-1/4’’ 11’’ 11’’ Top View of Tower...
  • Page 21 STEP 10 per board Flush Flush per joint Flush PANEL B PANEL B INSTALL...
  • Page 22 STEP 11 T-Nut Small 46-5/8’’...
  • Page 23 STEP 12 T-Nut Small HEADS FLUSH...
  • Page 24 STEP 13 Flush Flush Flush Flush Check to make sure structure is square Flush Flush Flush Flush Flush 46-5/8’’ PANEL E Flush FRAME C Flush FLIP FRAME OVER Flush...
  • Page 25 STEP 14 T-Nut Small LIFT FRAME UP Note: Tap each T-Nut into its pre-drilled hole until the metal tangs sink fully into the wood.
  • Page 26 STEP 15 Check to make sure structure is square Flush FRAME C Flush...
  • Page 27 STEP 16 Check to make sure structure is square Flush per joint PANEL D Flush Inside View of Tower 77-1/4’’ Flush...
  • Page 28 STEP 17 Flush per board per board PRE-DRILL Flush SUPPORTS 12-3/4’’ 12-3/4’’ Top View of Terrace...
  • Page 29 STEP 18 Flush per board...
  • Page 30 STEP 19 Flush Flush 2-1/4’’ Flush...
  • Page 31 STEP 20 Flush 26’’...
  • Page 32 STEP 21 Loc Nut Attach Tower Beam Support Board as shown.
  • Page 33 STEP 22 Swing Beam Large Hanger Beam Clamp Screws Correct Orientation...
  • Page 34 STEP 23 A-Frame SB Support A-Frame Small Small A-Frame Support Small...
  • Page 35 STEP 24 Bracket...
  • Page 36 STEP 25 Beam Brace Small Barrier Boards Removed for Clarity...
  • Page 37 STEP 26 Carriage Bolt Small Barrier Boards Removed for Clarity...
  • Page 38 STEP 27 Screws CENTERED Screws Screws Screws Front View Screws per board Screws Screws Screws per board Flush NOTE: Overlap Shingles as shown.
  • Page 39 STEP 28 TURN ROOF ASSEMBLY ON END. Flush Screws Flush per board per board Screws per board Flush OUTSIDE CENTER OUTSIDE OUTSIDE OUTSIDE OUTSIDE OUTSIDE OUTSIDE Flush Screws 1-1/2’’ 1-1/2’’ per board Flush Flush FLUSH AT BOTTOM Screws per board Cutaway View...
  • Page 40 STEP 29 Screws Screws Screws per board Screws Screws...
  • Page 41 STEP 30 ALIGN SCREWS WITH PRE DRILLS Flush Screws Per side Side View Top Screws per board Flush...
  • Page 42 STEP 31 Screws Flush Side View Bottom...
  • Page 43 STEP 32 Bolts...
  • Page 44 STEP 33 NOTE HOLES NOTE HOLES TABLE SUPPORT Top View of Table Inside View of Table...
  • Page 45 STEP 34 Flush Flush Check to make sure structure is square BOTH TABLE SIDES PRE-DRILL BOARDS WITH 1/8’’ DRILL BIT TO MINIMIZE SPLITTING BOTH SIDES Note: Pre-Drill boards with 1/8’’ drill bit as shown to prevent splitting.
  • Page 46 STEP 35 Flush Make Certain This Side Has Holes Closest To The Edge. Flush per side TO BOTTOM OF SUPPORT SUPPORT TO BOTTOM OF SUPPORT...
  • Page 47 STEP 36 per side...
  • Page 48 STEP 37 CENTERED per joint FLAP UP FLAP DOWN FLAP ON THE UNDERSIDE. FLAP ON TOP.
  • Page 49 STEP 38 ATTACH SLIDE INTO Screws Slide Stake...
  • Page 50 STEP 39 Pan Screw...
  • Page 51 STEP 40 NOTE: Crimp swing hanger tightly closed Ring-Trap Combo Assembly Attach Quick Link to chain oriented as shown.
  • Page 52 STEP 41 Swing Seat Assembly...
  • Page 53 STEP 42 Carriage Bolt Spacer Loc Nut Steering Wheel Assembly 1. Choose a desired location for the Steering Wheel and drill a 5/16” diameter hole through the lumber. NOTE: If lumber is greater than 2” in depth, you will need to counterbore the hole appropriately. 2.
  • Page 54 STEP 43 Telscope Assembly Mounting Screw Mounting Bracket Telescope Assembly STEP 44 Per Flag Flag Assembly...
  • Page 55 STEP 45 Fold up Anchor-It Strap Screw Anchor-It Note: Keep as little play as possible using any of the holes in the strap that work best. TIP: Drill Bit, or a long screw driver then insert and install the Anchor-Its as shown. This will allow you to get traction with the Anchor-It faster and allow the device to seat more securely.
  • Page 56 Components, Chains, Hardware and Fasteners – 5 years. These items to be free from defects in workmanship and materials, under normal use Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or materials.
  • Page 57 PRODUCT WARRANTY & REGISTRATION Please register online to properly initiate your product warranty & registration Quick & simple from home or mobile Record your purchase in our system Initiate product warranty Improved customer support Register your product online at www.OnlineWarranty.net...
  • Page 58 Call our Customer Support Representatives Printed in USA...

This manual is also suitable for:

Pb 8328Ws 8328

Table of Contents

Save PDF