Download
Share
Print this page
Swing-N-Slide PB 8360 Manual
  1. Manuals
  2. Brands
  3. Swing-N-Slide Manuals
  4. Play Sets & Playground Equipment
  5. PB 8360
  6. Manual

Swing-N-Slide PB 8360 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
PB 8360
Swing-N-Slide • 166 Etowah Industrial Ct. • Canton, GA 30114
Visit our website at:
playsupport@backyardproducts.com
or call us at 1-800-882-0272
LDR 01-14-2020
LA 8138

Advertisement

loading
Need help?

Need help?

Do you have a question about the PB 8360 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Swing-N-Slide PB 8360

Summary of Contents for Swing-N-Slide PB 8360

  • Page 1 PB 8360 Swing-N-Slide • 166 Etowah Industrial Ct. • Canton, GA 30114 Visit our website at: playsupport@backyardproducts.com or call us at 1-800-882-0272 LDR 01-14-2020 LA 8138...
  • Page 2 three 345 pounds and maximum 115 pounds on each swing. ...
  • Page 3 PLAYSET MAINTENANCE Cosmetic defects that do not affect the structural integrity of the product, or natural defects of wood such as warping, splitting, checking, twisting, shrinkage, swelling or any other physical properties of wood that do not present a safety hazard, are not covered by our warranty.
  • Page 4 PLAYGROUND SURFACING MATERIALS SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION'S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK Select Protective Surfacing One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment.
  • Page 5 MAXIMUM OF 115 lbs. ON EACH SWING AND TRAPEZE...

  • Page 6: Tools Required

    TOOLS REQUIRED INCLUDED HARDWARE 3/8" X 3-3/4" HEX BOLT (x 4) 1/4" LOCK WASHER (x 4) 3/8" FLAT WASHER (x 26) 3/8" X 3-3/4" CARRIAGE BOLT (x 4) TORX HEAD 3/8" LOCK WASHER (x 6) DRIVE (X2) 3/8" X 3-1/4" CARRIAGE BOLT (x 12) T-20 &...
  • Page 7 COMPONENTS PF 6090 2-3/8 X 5-1/8 X 87-1/2" SWING BEAM (x1) PF 6091 2-3/8 X 3 X 87-1/2" LEG (x4) PF 6092 3/4" X 3-3/8" X 68" A-BRACE (x2) FS 2911 SPACER (LOCATED IN SA 2675 HARDWARE BAG) 2449 L-BRACKET 2447R 2448L (x2)
  • Page 8 STEP 1: A-BRACE 3/8" X 3-3/4" HEX BOLT PF 6091 X 2 3/8" LOCK WASHER SWING LEG 3/8" FLAT WASHER PF 6092 X 1 3/8" T-NUT A-BRACE NOTE HOLE LOCATIONS. YOU WILL ASSEMBLE TWO A-FRAME POST ASSEMBLIES. MOVE POSTS APART AND LOCATE AND ATTACH A-BRACE INTO PRE-DRILLED HOLES. DO NOT FULLY TIGHTEN BOLTS AT THIS TIME.
  • Page 9 STEP 2: L-BRACKET 3/8" X 3-3/4" CARRIAGE BOLT PF 6091 SWING LEG 2449 L-BRACKET SUPPORT HINT: USE SWING BEAM. 3/8" FLAT WASHER 3/8" LOCK NUT USE A TEMPORARY SUPPORT UNDER ENDS AND CAREFULLY SWING POST TOGETHER UNTIL EDGES TOUCH. DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME.
  • Page 10 STEP 3: A-FRAME ANGLED BRACKETS 2448 X 1 2447 X 1 ANGLED BRACKET ANGLED BRACKET 3/8" X 3-1/4" CARRIAGE BOLT X 4 3/8" FLAT WASHER X 4 3/8" LOCK NUT X 4 YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. ATTACH ANGLED BRACKETS ON A-FRAME ASSEMBLIES.
  • Page 11 STEP 4: SWING HANGERS #6 X 1-1/4" WOOD SCREW X 12 PF 1574 3/8" LOCK NUT X 6 1-3/8" FLAT WASHER 3/8" FLAT WASHER X 6 FS 2911 SPACER X 6 WS 4456 X 6 SWING HANGER HOLD POSITION OF SWING HANGER WHILE TIGHTENING LOCK NUT.

  • Page 12: Step 5: Swing Beam Assembly

    STEP 5: SWING BEAM ASSEMBLY YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. 3/8" LOCK NUT 3/8" FLAT WASHER X 2 3/8" X 3-1/4" CARRIAGE BOLT POSITION SWING BEAM ASSEMBLY RESTING UPON ONE A-FRAME ONLY. ALIGN HOLES AND INSERT CARRIAGE BOLTS. DO NOT FULLY TIGHTEN CARRIAGE BOLTS AT THIS TIME.
  • Page 13 STEP 6: SWING BEAM ASSEMBLY 3/8" FLAT WASHER X 1 3/8' LOCK NUT YOU MAY NEED TO TAP BOLTS WITH HAMMER TO GET THROUGH HOLES. 3/8 X 3-1/4" CARRIAGE BOLT X 1 LAY A-FRAME ON THE GROUND WITH ANGLED BRACKETS FACING UP. POSITION SWING BEAM ASSEMBLY RESTING UPON A-FRAME.
  • Page 14 STEP 7: LIFTING SWINGSET SWING A-FRAME UP. 3/8" LOCK NUT X 1 3/8" FLAT WASHER X 1 3/8" X 3-1/4" CARRIAGE BOLT SWING A-FRAME UP AND INSERT SECOND BOLT. DO NOT FULLY TIGHTEN CARRIAGE BOLT AT THIS TIME.
  • Page 15 STEP 8: FINAL POSITION 104" 134 -1/2" 134 -1/2" TIGHTEN ALL LOCK NUTS UNTIL 2 THREADS MINIMUM EXTEND PAST NUT. MOVE PLAYSET INTO ITS FINAL POSITION. MAKE SURE PLAYSET IS SQUARE. FULLY TIGHTEN ALL FASTENERS AT THIS TIME. ENSURE TWO THREADS MINIMUM PROTRUDE PAST LOCK NUTS.
  • Page 16 STEP 9: SECURING L-BRACKETS 3/8" X 6" CARRIAGE BOLT X 2 TORQUE WASHER X 2 3/8" FLAT WASHER X 2 3/8" LOCK NUT X 2 TIGHTEN ALL LOCK NUTS UNTIL 2 THREADS MINIMUM EXTEND PAST NUT. RUN CARRIAGE BOLT THROUGH TORQUE WASHER AND USE A HAMMER TO SEAT THE TORQUE WASHER INTO SWING BEAM.
  • Page 17 STEP 10: SECURING PLAYSET PRE-DRILL 1/8" X 2" DEEP. 1/4" X 2-1/2" PAN HEAD SCREWS 1/4" LOCK WASHER X 4 #8 X 2-1/2" WOOD SCREWS X 8 SECURE PLAYSET WITH WOOD SCREWS AS SHOWN.

  • Page 18: Step 11: Trapeze Assembly

    STEP 11: TRAPEZE ASSEMBLY FIG. 11.1 24" CHAIN GREEN COATING DOWN. FIG. 11.2 2096 TRAPEZE FIG. 11.3 ATTACH CHAIN TO SPRING CLIP FIRST, POSITION AT TOP OF CLIP. (FIG 11.1) ATTACH SPRING CLIP TO TRAPEZE. (FIG. 11.2) CLOSE AND TIGHTEN SPRING CLIP. LOCK WITH PLIERS. (FIG. 11.3)

  • Page 19: Step 12: Swing Assembly

    STEP 12: SWING ASSEMBLY PLASTIC COATED END. QUICK CLIP X 4 FIG. 12.1 FACE NUT TOWARDS UNDERSIDE OF 48" CHAIN SWING. GREEN COATING DOWN. FIG. 12.2 FULLY TIGHTEN WITH PLIERS. FIG. 12.3 2434 SWING ATTACH CHAIN TO QUICK CLIP FIRST, POSITION AT TOP OF LINK AS SHOWN. (FIG. 12.1) PLACE THE QUICK CLIP THROUGH THE GROMMET OF THE SWING.
  • Page 20 STEP 13: HANGING SWING FIG. 13.1 INSERT CHAIN DIRECTLY INTO SWING HANGER. UNCOATED END OF CHAIN. FIG. 13.2 2096 TRAPEZE 56" 2434 2434 53" MAX 48" SWING SWING ADJUST CHAINS AT TOP. 8" MINIMUM WHEN OCCUPIED ADJUST CHAINS AT TOP. ATTACH THE SWINGS AND TRAPEZE CHAINS TO THE SPRING CLIPS ON THE SWING HANGERS AS SHOWN.
  • Page 21 STEP 14: ANCHOR-IT AT LOCATIONS CIRCLED ABOVE, TWIST THE ANCHOR-IT INTO THE GROUND UNTIL ONLY THE LOOP IS EXPOSED. PLACE ANCHOR-IT STRAP THROUGH, FOLD THE ENDS TOGETHER AND ATTACH TO THE UNIT AS SHOWN. NOTE: KEEP AS LITTLE PLAY AS POSSIBLE USING ANY OF THE HOLES IN THE STRAP THAT WORK BEST. TIP: WHEN INSTALLING ANCHOR-IT IN ROCKY OR HARD SOIL, CREATE A STARTER HOLE AT THE DESIRED LOCATIONS USING EITHER A 16"...
  • Page 22 Plastic Components, Chains, Hardware and Fasteners – 5 years. These items to be free from defects in workmanship and materials, under Swing-N-Slide® will repair, or at its discretion, replace any part within the stated warranty period which is defective in workmanship or 166 Etowah Industrial Janesville, Wisconsin, 53545.
  • Page 23 Got Questions? We’ve got answers! Call our Customer Support Representatives 1-800-882-0272 Available Monday - Friday, 8am - 5pm (EST) Technical support from experienced Swing-N-Slide customer service representatives who have actually built a swing set themselves. © Swing-N-Slide Inc. 2020...