Page 1
Eaton SFX Product Family Installation and Operation Manual SFX Product Line...
Page 2
DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or other-wise for any special, indirect, incidental or consequential damage or loss...
Page 3
The situation described in the CAUTION may, if not avoided, lead to serious results. Important safety measures are described in CAUTION (as well as WARNING). EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
CAN-based devices such as displays and keypads, in applications that require a functional safety solution. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Maximum Input Frequency (FREQ) (0-5 V square wave) 0 Hz...50 kHz* in Freq. mode Note: maximum aggregate is 200 kHz, minimum detectable pulse duration is 20 μsec EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Page 8
W6S-P012, sealing plug P/N 0413-217-1605 P Connector Tooling Manufacturer Deutsch P Connector Hand Tool Part Number Solid contacts: Service crimper: HST-1561 Production crimper(ratcheting): HDT-48-00 Stamped contacts: DTT-16-00 EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Additionally, the CANLayer2 software library is available for use with CAN bus. SFX controllers are programmed via CAN using Eaton’s Universal Service Tool (UST.) EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Page 10
Number of channels supporting function 0 - 5 V input 0 - 10 V input 0 - 32 V input 4 - 20 mA input Pull-up resistor Pull-down resistor Thermistor EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Page 11
Closed loop PWM with current control • The 2 x 4 A channels are also capable of Low Side output and can be configured as a pair for H-Bridge operation. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Please check with your enclosure manufacturer • for appropriate guidelines concerning the necessary enclosure volume to adequately limit thermal rise below the maximum operating temperature of 105°C EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Avoid routing near wheel wells or provide • adequate mechanical protection to the assembly. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Page 14
SFX controller and sealed mating connectors without wires are installed in the SFX connector ports prior to electrostatic painting on the machine. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Note: Both SFX units share a common pin-out. The SFX12m does not utilize the following pins: 8, 15, 17, 25, 27, 31, 32, and 40. DT04-6P The above connector is used for programming and is common to both models of the SFX controller. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
5 four hour cycles, two hours @ -40°C & two hours @ 105°C Humidity/Temp Cycling J1455 Section 4.2.3 Six 48 hour cycle at 20°C to 60°C, 90 - 98% RH EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
5. Verify the CAN_H and CAN_L lines have not been crossed. 6. With the CAN network active measure from CANH to VBATT- and CANL to VBATT-. EATON SFX Product Family Installation and Operation Manual 6045988-001 Rev. A E-ELCL-II005-E March 2019...
Need help?
Do you have a question about the SFX Series and is the answer not in the manual?
Questions and answers