1. Manuals
  2. Brands
  3. Eaton Manuals
  4. Controller
  5. S611
  6. Quick start installation manual

Eaton S611 Quick Start Installation Manual

Soft starter
Hide thumbs Also See for S611:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
S611 Soft Starter
Quick Start Installation Guide
Effective January 2012
Supersedes June 2011
www.comoso.com

Advertisement

Table of Contents
loading

Related Manuals for Eaton S611

Summary of Contents for Eaton S611

  • Page 1 S611 Soft Starter Quick Start Installation Guide Effective January 2012 Supersedes June 2011 www.comoso.com...
  • Page 2 www.comoso.com...

  • Page 3: Disclaimer Of Warranties And Limitation Of Liability

    OBLIGATION OF EATON. THE CONTENTS OF THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY ANY CONTRACT BETWEEN THE PARTIES. In no event will Eaton be responsible to the purchaser or user in contract, in tort (including negligence), strict liability or otherwise for any special, indirect, incidental or consequential...

  • Page 4: Support Services

    S611 Soft Starter Support Services The goal of Eaton is to ensure your greatest possible satisfaction with the operation of our products. We are dedicated to providing fast, friendly, and accurate assistance. That is why we offer you so many ways to get the support you need. Whether it’s by phone, fax, or e-mail, you can access Eaton’s support information 24 hours a day, seven days a week.

  • Page 5: Installation

    Do not apply a disconnect device on the output of the S611 soft starter unless a means to turn off the soft Note: When securing the lugs onto the bus bars of the soft starter when disconnect switch is open is used. Opening...

  • Page 6: Short-Circuit Rating

    Suitable for use on a circuit capable of delivering not more than 100,000 rms symmetrical amperes, 600 volts maximum when protected by Class RK5 fuses or a circuit breaker having an interrupting rating not less than 65,000 rms symmetrical amperes, 480 volts maximum. S611 Soft Starter MN03901003E—January 2012 www.eaton.com www.comoso.com...
  • Page 7 127,0 70.0 70.0 [5.00] [5.00] [2.76] [2.76] 155.0 110.0 [6.10] [4.33] 464.7 [18.30] 562.0 [22.13] 80.0 80.0 Ø 10.0 [3.15] [3.15] [0.39] 90.0 [3.54] Ø 10.0 127,0 127,0 [0.39] [5.00] [5.00] 155.0 [6.10] S611 Soft Starter MN03901003E—January 2012 www.eaton.com www.comoso.com...
  • Page 8 98 97 96 13 14 Relay 2 Relay 1 Relays 120 Vac Comms Adapter Supply DeviceNet 120 Vac Modbus Control PROFIBUS TB5 (Module) +24V Comms Modbus Comms Port B Common TB5 (Connector) User Interface Module S611 Soft Starter MN03901003E—January 2012 www.eaton.com www.comoso.com...
  • Page 9 Selects/Saves parameter values in Advanced Config. Parameters ● No function in Monitor mode ● Fault Log ● View 10 most recent fault codes ● Reset ● Trip reset button if no active faults are present ● S611 Soft Starter MN03901003E—January 2012 www.eaton.com www.comoso.com...
  • Page 10 Setup and Starting—Initial Configuration Setup and Starting—Initial Configuration The S611 Operation and Protection parameters may be Enter Stop time, Kick Start time, and Kick Start edited when 120 Vac control power is applied to 120 Vac torque if desired (default = 0).

  • Page 11: Torque Settings And Corresponding Current Values

    — 175% Possible high starting torque Press, flywheel — 150% Possible high starting torque Drier, rotating — 100% — Blower, axial fan, flaps open — — Blower, centrifugal fan, valve open — — S611 Soft Starter MN03901003E—January 2012 www.eaton.com www.comoso.com...

  • Page 12: Troubleshooting

    Cycle 120 Vac control voltage power to attempt to • Possible hardware failure clear problem Internal Program Memory • Corrupted firmware or memory • Cycle 120 Vac control power to the S611 • Flash CRC • Contact EatonCare for service Voltage Zero Cross Lost • Mains voltage lost •...
  • Page 13 Operation mode • Only active when Stall Fault is disabled • Reduce starting load • Verify S611 is properly rated for current Under Load • Loss of motor load • Inspect for failed motor coupling or pump cavitation •...
  • Page 14 Only active in bypass if the jam fault is • Remove obstruction in motor drive train disabled • Verify S611 is properly sized for the application • Current exceeds the fault threshold of 4 x catalog FLA Missing Temp Sensor •...
  • Page 15 www.comoso.com...
  • Page 16 Eaton is dedicated to ensuring that reliable, efficient and safe power is available when it’s needed most. With unparalleled knowledge of el ectrical power management across industries, experts at Eaton deliver customized, integrated solutions to solve our customers’ most critical challenges.

Table of Contents