Advertisement
Advertisement
Related Manuals for Fireco Dorgard Pro
Summary of Contents for Fireco Dorgard Pro
- Page 1 Compliance Made Easy Handbook 2019-07-17...
-
Page 2: Table Of Contents
Compliance Made Easy Contents Section 1: Pro system overview Page 1 Section 2: Survey and demo Page 7 Section 3: Installation Page 10 Section 4: Troubleshooting Page 13 Section 5: Maintenance Page 19 Section 6: Notes Page 20... -
Page 3: Section 1: Pro System Overview
The Transmitter, which is connected to an alarm panel, will ensure all connected devices release when an alarm is activated, preventing the spread of smoke and fire. Part Number Part Name 885-3205 Fireco Transmitter 966-2075 Fireco Repeater 775-5231 Pro Timer 360-1551 Dorgard Pro Black 956-8278 Dorgard Pro White 338-0604 Freedor Pro Page 1... - Page 4 Pro system overview Fireco Transmitter The Transmitter is a radio control unit for the Pro system. Connected to a fire alarm relay, it controls and monitors the system. Radio Fire Power Alert Power 8-30V AC or DC Two x LR14 C-size batteries, capable of operating system...
- Page 5 Pro system overview Fireco Repeater The Repeater extends the radio range from the Transmitter, allowing you to connect more units over a greater distance. Up to 50 Repeaters may be used in any installation. Radio Fire Power Alert Power 8-30V AC or DC...
- Page 6 Pro system overview Pro Timer A Pro Timer is a digital timer device which can be bound to a Transmitter or a Repeater. It can be programmed to release all the devices further down the system for a set period of time.
- Page 7 Dorgard Pro Dorgard Pro is a fire door hold open device which can retain a fire door at any angle of opening. When the fire alarm is activated, the Transmitter sends a radio signal to the Dorgard Pro to release all doors, preventing the spread of smoke and fire.
- Page 8 Fire Radio Power 9V Alkaline battery pack Battery life Five years Triggers Fireco Transmitter Radio frequency 433.050 MHz to 434.790 MHz Applicable door size Up to EN3 60Kg, 950mm Freedor has been tested to EN1634-1 on FD30 doorsets, Fire rating...
-
Page 9: Section 2: Survey And Demo
Survey Transmitter to the right. 2. Binding Dorgard Pro Depress the plunger on your Demo Dorgard Pro. This will bind the two units and enable you to survey a building. Dorgard Pro Freedor Pro Push the button on the front of unit. - Page 10 Survey and demo Dorgard Pro Place the Survey Dorgard Pro at the position a Dorgard Pro is to be fitted. Hold it at the bottom of the fire door. Depress the plunger to get a radio reading. If the Dorgard Pro is in range of the Survey Transmitter, the top LED of the Dorgard Pro will show solid green for 4 seconds.
- Page 11 Switch the Pro Demo and Site Survey Transmitter into demo mode by flicking the switch on the base of the Survey Transmitter to the left. Dorgard Pro Press down the plunger on the Demo Dorgard Pro. Dorgard Pro Freedor Pro Push the button on the front of the unit.
- Page 12 1A fused spur using the kettle lead. If powered direct, it requires any voltage between 8-30v AC or DC. Dorgard Pro has 2 C cell batteries included and connected. The battery compartment is accessed by the screw on top of the unit.
- Page 13 This can be done by pressing the bind button. Dorgard Pro The bind button can be accessed through the front casing using a 3mm screwdriver. The radio LED will flash green to indicate in bind mode.
- Page 14 This can be done by pressing and holding the bind button. On a Dorgard Pro it is accessed through the front casing using a 3mm screwdriver. Dorgard Pro The radio LED will flash amber to indicate in unbind mode.
- Page 15 Troubleshooting section Section 1: Failing to bind Page 14 Section 2: Red radio LED and red alert on device Page 16 Section 3: Factory reset Page 17 Section 4: Dorgard Pro is marking the floor Page 18 Page 13...
-
Page 16: Section 4: Troubleshooting
Troubleshooting Failing to bind Pro devices Dorgard Pro State Dorgard Pro The Pro devices will indicate failure to bind by showing the radio LED and alert LED as red. It will then take itself out of bind mode. Check 1. Check that the Transmitter or Repeater to which you want the Pro devices to bind is in bind mode. - Page 17 LED stops flashing and turns solid green for 4 seconds, it has bound to the Transmitter or parent Repeater. Dorgard Pro If problem persists, it is likely the Repeater is out of range. We recommend you carry out a site survey - see section 2.
- Page 18 Carry out a site survey to ensure sufficient range Dorgard Pro where the device is located, it may be necessary to: Re-site Transmitter or Repeater;...
- Page 19 The reset restores the device to the original manufacturer settings. Any connected devices will be unbound. Dorgard Pro Undo battery compartment and pull up to disconnect power. Hold down the bind button whilst reconnecting power until it beeps 3 times.
- Page 20 Scan to watch our technical support video Dorgard Pro has an anti-drag feature. When activated if the door is pulled, the Dorgard Pro will release allowing the door to close. To activate contact Fireco Technical Support team on +44(0)1273 320650 who will provide you with the required sound file.
-
Page 21: Section 5: Maintenance
Declaration of Performance is available upon request +44 (0) 1273 320650 +32 (0) 56 28 00 65 +4 (0) 6812 050480 +44 (0) 1273 320650 support@fireco.uk info@connect2safety.be info@safetyco.se intsales@fireco. Compliance Made Easy Fireco Ltd Page 19... -
Page 22: Section 6: Notes
Notes Page 20... - Page 23 Notes Page 21...
- Page 24 Fireco provides simple and trusted solutions for your common fire safety problems Call us today 01273 320650 www.fireco.uk...