U-Line H-1114 Manual page 7

WEIGHT TOTALIZING CONTINUED
3. When scale stabilizes, UNIT WEIGHT displays the total
number of additions.
WEIGHT
118.3
SMPL
→ 0←
WT
PC
NET NET
WT
4. After 3 seconds, scale returns to weighing mode.
WEIGHT
118.3
SMPL
→ 0←
WT
PC
NET NET
WT
CLEAR ALL TOTALIZED VALUES
Press MC to clear all of the totalized values. " " next
to M+ icon on QUANTITY display switches off. Totals for
weight, number of additions and quantity reset to zero.
NOTE: All totals will be lost if the scale is
switched off.
CALIBRATION
AUTO CALIBRATION
You must use calibration weights to accurately calibrate
the scale. Calibration weights totaling at least 10% of
scale's capacity must be used for accurate calibration.
NOTE: Calibration weights are sold separately.
See uline.com for details.
1. With the scale displaying "0," press and release
WEIGHT
1500.0
SMPL
→ 0←
WT
PC
NET NET
WT
• and UNIT WEIGHT PRESET keys simultaneously. After
approximately five seconds, the WEIGHT display
flashes the scale capacity.
2. Place weights on the scale equal to the full load
capacity. When scale stabilizes, press the MC key.
3. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
4. Press CE to exit from the calibration mode.
NOTE: If weights equalling the full load are not
available, you can enter a weight that is less
than the full load.
5. With the scale displaying "0," press and hold
press UNIT WEIGHT PRESET until the WEIGHT display
flashes the scale capacity. Release the keys.
PAGE 7 OF 30
USING THE SCALE CONTINUED
UNIT WEIGHT QUANTITY
1
M+
STABLE
UNIT WEIGHT QUANTITY
0
M+
STABLE
UNIT WEIGHT QUANTITY
501
M+
STABLE
6. Enter the weight to be used, then place the weight
on the scale. When the scale stabilizes, press the MC
key.
7. While the scale counts down to 0, remove the
weights from the scale. The calibration is complete.
0
8. Press CE to exit from the calibration mode.
Pcs
RECALL THE ORIGINAL CALIBRATION VALUES
1. Press and hold CE, then press UNIT WEIGHT PRESET
until the scale counts down to 0. Release the keys.
The scale will revert to the original factory calibration
0
values.
Pcs
UNIT WEIGHT PRESET MEMORY
The scale can store 10 sets of unit weight presets in the
number keys (0-9). Once saved, pressing a particular
number key will display the unit weight saved in that
memory.
NOTE: The UNIT WEIGHT PRESET key is a dual
function key. Determine if unit weight preset
is set as the main function or the secondary
function of this key. If unit weight preset is the
secondary function, hold the UNIT WEIGHT
PRESET key down for three seconds to activate
the feature.
SETTING A UNIT WEIGHT PRESET
1. Use the number keys (0-9) to enter the unit weight
value you wish to save.
WEIGHT
0.0
→ 0←
NET NET
2. Press UNIT WEIGHT PRESET.
Pcs
WEIGHT
PrSEt
→ 0←
NET NET
3. Press UNIT WEIGHT PRESET again.
WEIGHT
PrSEt
→ 0←
NET NET
4. Press any number key (0-9) to save the weight in that
key's memory.
.
WEIGHT
0.0
→ 0←
, then NET NET
UNIT WEIGHT
100
SMPL
M+
WT
PC
STABLE
WT
UNIT WEIGHT
SMPL
M+
WT
PC
STABLE
WT
UNIT WEIGHT
SEt
SMPL
M+
WT
PC
STABLE
WT
UNIT WEIGHT
100
SMPL
M+
WT
PC
STABLE
WT
QUANTITY
0
Pcs
QUANTITY
Pcs
QUANTITY
Pcs
QUANTITY
0
Pcs
1119 IH-1114