Welding Wire Spool Setup: 4" (100Mm); Welding Wire Spool Setup: 8" (200Mm); Drive Roll Types And Sizes - Pro-Tec Welding PRO-TEC 215 MP Operating Manual

INSTALLATION

4.9 Welding Wire Spool Setup: 4" (100mm)

1. Open the Wirefeed Compartment Door by lifting the two
latches in the door panel.
2. Push the Adjustable Pressure Device towards the front
panel.
3. Lift the Idle Roll Assembly to a vertical position.
4. Check the Drive Roll groove size and type suits the Welding
Wire.
5. Fit the 4'' (100mm) Spool as shown.
6. Tighten the plastic Tension Screw to ensure spool rotates
with slight tension.
7. Hold the Welding Wire end on the Spool then cut off the
bent end.
8. Manually feed the Welding Wire from the Spool into the
Inlet Guide and over the top of the Drive Roll.
9. Continue to feed the wire through the Outlet Guide until 1''
(25mm) of Welding Wire is protruding out of the Gun Adap-
tor.

4.10 Welding Wire Spool Setup: 8" (200mm)

1. Open the Wirefeed Compartment
Door by lifting the two latches in
the door panel.
2. Push the Adjustable Pressure
Device towards the front panel.
3. Lift the Idle Roll Assembly to a
vertical position.
4. Check the Drive Roll groove size
and type suits the Welding Wire.
5. Fit the 8'' (200mm) Spool as
shown.
6. Align locking pin on spool hub
with hole in spool.
7. Tighten the plastic Tension Screw
to ensure spool rotates with slight
tension.
8. Hold the Welding Wire end on the Spool then cut off the bent end.
9. Manually feed the Welding Wire from the Spool into the Inlet Guide
and over the top of the Drive Roll.
10. Continue to feed the wire through the Outlet Guide until 1'' (25mm)
of Welding Wire is protruding out of the Gun Adaptor.

4.11 Drive Roll Types and Sizes

Part No.
G7100000
G7100001
G7100002
G7100003
G7100004
Not recommended
for MIG Gun,
use Spool Gun
G7100005
Operating Manual No: PWOM-215/250MP-001
NOTE 10: Check the MIG GUN Liner and Contact Tip are sized to match the
Welding Wire.
10. Lay the Idle Roll Assembly down to a horizontal position.
11. Push the Adjustable Pressure Device up to a vertical position and adjust
Pressure Device if needed. DO NOT over tighten.
NOTE 11: Check the MIG GUN Liner and Contact Tip are sized to match the Welding Wire.
11. Lay the Idle Roll Assembly down to a horizontal position.
12.
Groove Type
Plain V Groove
Knurled V Groove
Plain U Groove
Page 22
Push the Adjustable Pressure Device up to a vertical position and
adjust Pressure Device if needed. DO NOT over tighten.
Wire Sizes
.024"/.030"
(0.6mm - 0.8mm)
.030"/.035"
(0.8mm - 0.9mm)
.035"/.045"
(0.9mm – 1.2mm)
.030"/.035"
(0.8mm - 0.9mm)
.035"/.045"
(0.9mm – 1.2mm)
.030"/.035"
(0.8mm – 0.9mm)
.040"/.045"
(1.0mm – 1.2mm)
Wire Materials
Fe , Ss
(Iron) (Stainless)
Solid Welding Wire
Fe , Ss
(Iron) (Stainless)
Solid Welding Wire
Fe , Ss
(Iron) (Stainless)
Solid Welding Wire
FCAW-S, FCAW-G
Flux Cored Welding Wire
FCAW-S, FCAW-G
Flux Cored Welding Wire
Al
(Aluminum)
Soft Welding Wire
Al
(Aluminum)
Soft Welding Wire
© 2018 Global Welding LLC