Mig Syn Setup For Mig/Fcaw (Gmaw) - Pro-Tec Welding PRO-TEC 215 MP Operating Manual

4.8 MIG SYN Setup for MIG/FCAW (GMAW)

Danger! Protect Electric shock
yourself and can kill
others
NOTE 9: Wide safety margins provided by the design allow the Power Source will withstand short term overloads without fail-
ure. The Welding Setup Data values should be used as a guide only then fine tune one or more of the Welding Setup Data values
to suit the welding application.
Before connecting the welding cables make sure the Input Power Supply is switched off. Remove any packaging ma-
terial prior to use. Do not block the air vents at the front or rear of the Power Source.
MIG SYN Setup Sequence
Refer to: - Section 4.9 Welding Wire Spool Setup: 4"
- Section 4.10 Welding Wire Spool Setup: 8"
- Section 4.11 Drive Roll Types and
- SECTION 5 – OPERATION
1 Switch the Power Switch (located on the rear panel) to OFF
position.
2 Connect the leads as follows:
a. Earth Clamp Lead to the Negative Output Terminal for MIG
or Positive Output Terminal for FCAW.
b. MIG Gun Lead to the MIG Gun Adaptor.
c. 8 Pin Plug to 8 pin socket.
d. Gas Hose to the Gas Input on rear panel then turn ON the
shielding gas. DO NOT over tighten the gas fittings.
3 Plug the Power Source into Input Supply Voltage.
4 Switch the Mains Power Supply ON & Power Switch (located
on the rear panel) ON. This will immediately energize the
Power Source.
5 Rotate Knob then PUSH to SELECT:
Welding Mode Selection
a. to MIG SYN
b. Welding Material Selection to Fe or Ss or Al or FCAW-S or
FCAW-G
Protective Gas Selection
c. to Mix Gas or CO
d. Welding Diameter Selection to:
Model Material 120 VAC
Fe .023/.030''/.035''/.040''
Ss .030''/.040''
215MP
Al .035''/.040''
FCAW-S .035''/.040''/.045''
FCAW-G .040''/.045''
Fe .023/.035''/.040''
Ss .030''/.040''
250MP Al .035''/.040''
FCAW-S .035''/.040''/.045''
FCAW-G .040''/.045''
Welding Type Selection
e. to 2T or 4T
Thickness
f. to Plate thickness to be welded.
6 Set Switch to MIG GUN & LINK to MIG or FCAW located
behind the Wirefeed Compartment Door.
7 Commence welding.
8 If needed, adjust the Weld Amperage value by changing
Inch/Min Control Knob to obtain the welding condition
required.
9 If needed, adjust Arc Voltage ''V'' Control Knob.
10 If needed, adjust Inductance Control Knob to fine tune the
welding arc.
11 Leave Power Switch ON for 3 minutes to cool down internal
components after welding completed.
12
Switch the Power Switch to the OFF position and turn OFF
the shielding gas.
POWER DOWN the Power Source by switching the machines Power Switch OFF then unplugging the Input Power Cord from the wall
socket or wall disconnect device. Use established Lockout/Tagout procedures, refer to OSHA 29 CFR 1910.147, when disconnecting
the Welder's Input Power Cord from the Input Supply Voltage.
© 2018 Global Welding LLC
Flying metal or Arc rays can
dirt can injure burn eyes and
eyes skin
(100mm).
(200mm).
Sizes.
for explanation of controls.
2
208/230/240 VAC
.023/.030''/.035''/.040''
.030''/.040''
.035''/.040''
.035''/.040''/.045''
.040''/.045''
.023/.030''/.035''/.040''/.045''
.030''/.040''/.045''
.035''/.040''/.045''
.035''/.040''/.045''
.040''/.045''
Page
21
Fumes and Welding can
gases can be cause fire or
hazardous explosion
Operating Manual No: PWOM-215/250MP-001
INSTALLATION
Improper instal- Read Operating
lation can cause Manual
fire