Setting Up The Pump; Safety Information - Bio Compression Systems SC 2008 OC User Manual

4. Setting up the Pump

Please refer to the Quick Guide and General Settings Guide to set up your pump, apply
garments and configure settings.
*PLEASE NOTE: You should be guided by a clinician regarding what settings you
should apply for treatment including pressure, cycle time and therapy duration.
BIO-COMPRESSION Set-up Guide: pants
Biocompression Pump
This guide is intended as a quick reference once the user manual has been read in-full
© 2019 Medi-Rent Pty Limited
SC 2008 OC
settings guide:
PH: 1300 726 666
Medi-Rent Pty Limited
8 chamber leg garments or biopants
ABN: 37 603 454 360
Unit 3, 61 Beauchamp Rd, 1
Matraville NSW 2036
P: 1300 726 666
This protocol has been
F: 02 9316 9998
developed as a guide only.
E: info@medirent.com.au
W: www.medirent.com.au
Please consult with your
therapist for treatment
settings to suit your
Place the device somewhere easily
individual needs. accessible.
Wear lightweight long pants under the Bio
Compression pants.
3 4
SC-2008-OC 40 45 45 40 50 50 ON |
Sequential Circulator 35 30 35 30 5560 55 60
25 25 70 75 75 70 65 65
20 20 PRESSURE PRESSURE 80 80 OFF 0
8 8 7 7 6 6 5 5 4 4 2 2 3 3 1 1
8 8 7 7 6 6 5 5 Rx ONLY Rx ONLY 4 4 3 3 2 2 1 1
8 7 6 5 4 3 2 1
Connect cuff hose to the device, ensuring Find the position where you will be rested
the numbers and indicators match. during treatment on a bed or couch where
your legs are elevated and supported.
6 7
Ensure you are on a non-slip surface. Stand up Sit as far back on the chair or bed as able.
with the garment partially zipped up. Lift the
trousers and zip the remainder of the garment
on each side. Adjust the garment to fit your
body without rotating, twisting, or large
creasing of the material.
Pressure sensor
The pressure sensor monitors and adjusts the garment pressure throughout inflation to
ensure filling of the garment approximates the pressure setting on the device.
The function of the sensor enables appropriate filling regardless of the size or style of garment
attached to the controller or the limb size within the garment.
It is normal for the garment to feel loose during the first few cycles before the unit fills each
chamber to the selected pressure. This may take longer for the arm-vest.
If the system doesn't reach set pressure, then the device will alarm indicating there is a fault
with either the garment or the controller. Please see 'Troubleshooting Guide' later in this
booklet to determine the cause of the fault and how to rectify it.
10
MEDIRENT.COM.AU © 2020
2
Plug your power lead in, ensuring that it is
not a trip hazard.
(Often you will need to visit the bathroom
during treatment due to fluid evacuation).
5
Unzip the pant garment partially and place
it on the couch or bed. If seated, step each
foot into position ensuring the heels are
located to the back of the garment. Zip the
legs up as far as you can.
8
Use your upper body as a counter weight to
lift your legs up onto the couch/bed.

5. Safety Information

WEEE Marking
This marking shown on the product or its literature, indicates that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment or
human health from uncontrolled waste disposal, please separate this
from other types of waste and recycle it responsibly to promote the
sustainable reuse of material resources.
Household users should contact Local Council about how and where
they can dispose of this item for environmentally safe recycling.
Business users should contact their supplier and check the items
and conditions of the purchase contract. This product should not be
mixed with other commercial waste for disposal.
11