Bosch Indego M 700 Original Instructions Manual page 26

26 | English
Remove stones, loose pieces of wood, wire, live mains
cables and other foreign objects from the cutting area.
Make sure that the cutting area is even and has no ditches,
grooves and steep slopes above 15°/27 %, which are clear
obstructions for the mower.
The docking station must be positioned on the wire at an
outer edge of the cutting area. It may not be positioned on
the side of a tool or garden shed standing as an island within
the lawn to be mowed.
It is recommended that you mow your lawn once with a con-
ventional lawnmower before installing and before the first
mowing of the new season and whenever the grass clippings
would be longer than 5 mm.
The mower's cutting system is designed to cut small lengths
of grass (30–50 mm). The clippings can remain as mulch to
fertilize the lawn. The height of cut for mower can be adjus-
ted to 30, 40 and 50 mm.
It is recommended to start with a higher setting and then
gradually decrease the height of cut as the wire disappears
under the grass. This prevents your Indego from cutting the
wire.
Additional perimeter wire can be added using a wire con-
nector (see figures D–E).
The perimeter wire can be extended up to a maximum length
of 350 m.
The perimeter wire can be buried up to 5 cm under the
ground (or under non-metallic slabs).
To avoid causing damage to the perimeter wire, do not verti-
cut or rake the area where it is positioned.
When laying out the wire avoid angles of less than 45°. This
can affect the performance.
Display
Symbol Meaning
➊ Back button
Confirm button
➋
If the confirm button is pressed whilst mow-
ing, the mower will return to the docking
station
➌ ○ Red LED on: mower error
➍ ○ Green LED on: mower is switched on
F 016 L81 041 | (15.04.2020)
Symbol Meaning
Green LED off: The mower is inactive and
your four-digit PIN code is required for ac-
tivation.
Or the mower is shut off, the isolator switch
must be turned on and your four digit PIN
code must be entered to activate the
mower.
Note: during a software update, the green
LED and red LED will be on.
Left/right button
➎
Down/up button
➏
➐ Display with dialog screen
➑ 1 2 3 Garden number (shown when more than
one garden map in the mower memory)
Only with Indego M+ 700:
➒ Network signal present
Network signal absent
The display switches into sleep mode, if no input is made for
10 minutes.
Adding a further Garden/Lawn Area
(see figure K)
To install the Indego to an additional lawn area, please follow
the instructions in the Installation Guide.
Separate garden with separate docking station (see fig-
ure K, right side): The mower can be used on up to three
different gardens. For an additional garden, a separate dock-
ing station (see figure A) and the necessary perimeter wire
and pegs are required. If a schedule or the "Bosch AUTO"
calendar function or the Bosch "SmartMowing" functional-
ity is set, the grass of the area it is in will be cut, within the
defined time slots.
Switch off the mower when transporting it between the indi-
vidual gardens.
Note: software updates have to be carried out on the mower
in every docking station.
To ensure remembering which docking station belongs to
which garden, it is recommended to label the docking sta-
tions with the garden number and description when storing
them for winter.
Without separate docking station: It is possible to connect
the lawn area by placing the perimeter wire between the two
lawn areas parallel to each other as close as possible (see
figure K, top left). The additional lawn area without docking
station is not recorded in the map memory and the mower
will not use the LogiCut cutting strategy in this lawn area
without the docking station. The maximum recommended
lawn area without a docking station is 50 m
mow until it runs out of battery and will need to be carried
back to the docking station for charging.
2
. The mower will
Bosch Power Tools