Download Print this page

Axxess AXGMLN-08 Installation Instructions Manual

Gm data interface 2012-2016

Advertisement

Available languages

Available languages

Quick Links

Installation instructions for part AXGMLN-08
GM Data Interface
• Provides accessory power
(12-volt 10-amp)
• Retains R.A.P. (retained
accessory power)
CHEVROLET
Avalanche † *
2012-2013
Express †
2013-2015
Malibu (with single color,
monochrome display) * 2013-2015
Malibu Limited (with single color,
monochrome display) *
2016
* These vehicles have an amplifier option. Please reference the "Service Parts Identification" sticker located in the
glove box for the RPO code UQ7 or Y91. If UQ7 or Y91 are present, then the vehicle is equipped with an amplifier.
Either use the AXGMLN-07 interface, or bypass the amplifier.
† Only for models with NAV.
Axxess Integrate
AXGMLN-08
2012-2016
INTERFACE FEATURES
• Provides NAV outputs (parking
brake, reverse, and speed sense)
• Retains chimes
• Retains OnStar/OE Bluetooth
• Adjustable OnStar level
APPLICATIONS
CHEVROLET (CONT)
Silverado 2500/3500 † *
2014
Silverado † *
2012-2013
Suburban † *
2012-2014
Tahoe † *
2012-2014
Trax *
2015-2016
axxessinterfaces.com
• Designed for non-amplified
models, or when bypassing
a factory amp
• Retains balance and fade
• AXUSB-CBL updatable
(sold separately)
GMC
Savana †
2013-2015
Sierra 2500/3500 † *
2014
Sierra † *
2012-2013
Yukon/Yukon XL † *
2012-2014
metraonline.com
Table of Contents
Connections to be made ................................................... 2
Installing the AXGMLN-08 ................................................ 3
Initializing the AXGMLN-08 .............................................. 3
Adjusting the AXGMLN-08 ................................................ 3
INTERFACE COMPONENTS
• AXGMLN-08 interface • AXGMLN-08 harness
• 16-pin harness with stripped leads
TOOLS REQUIRED
• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2020 METRA ELECTRONICS CORPORATION

Advertisement

loading

Summary of Contents for Axxess AXGMLN-08

  • Page 1 INTERFACE COMPONENTS a factory amp • Retains chimes • Retains R.A.P. (retained • AXGMLN-08 interface • AXGMLN-08 harness accessory power) • Retains balance and fade • Retains OnStar/OE Bluetooth • 16-pin harness with stripped leads •...
  • Page 2: Connections To Be Made

    • Connect the Red wire to the accessory wire. • Connect the Light Green wire to the parking brake wire Note: The relay attached to the AXGMLN-08 harness is only for audible turn signal clicks. No extra steps are required to retain this feature, so leave the...
  • Page 3: Installing The Axgmln-08

    OnStar Level Adjustment • Press the OnStar button to activate it. • Connect the 16-pin harness with stripped leads, and the AXGMLN-08 harness, into the interface. • While OnStar is speaking, press the VOLUME UP or VOLUME DOWN button on the steering wheel to raise or lower the OnStar level.
  • Page 4 Installation instructions for part AXGMLN-08 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated.
  • Page 5 Además, no culo está equipado con un amplificador. Utilice la interfaz AXGMLN-08 o elimine el amplificador. quite el radio de fábrica con la llave en la posición o de encendido ni †...
  • Page 6 • Conecte el cable verde claro al cable de freno de mano. • Conecte el cable rojo con el cable de accesorios. Nota: El relé adjunto a la interfase Axxess únicamente es para los chasquidos audibles de la señal direccional. No se requieren pasos adicionales para retener...
  • Page 7 Ajuste del nivel de OnStar • Presione el botón OnStar para activarlo. • Conecte el arnés de 16 pins con conectores pelados, y el arnés AXGMLN-08, al • Mientras OnStar está hablando, presione los botones de “SUBIR VOLUMEN” o interfase.
  • Page 8 Instrucciones de instalación para la pieza AXGMLN-08 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...