Cab3/Cab4 Cabinet Installation - Honeywell NOTIFIER ONYXWorks NFN Gateway Installation & Operation Manual

NFN Gateway Embedded Installation

2.3 CAB3/CAB4 Cabinet Installation

Step 1. Install a new CAB-3/CAB-4 series cabinet according to the requirements of the local
NOTE: The CAB3/CAB4 cabinet is ordered separately. For installation details, refer to the CAB-
3/CAB-4 Series Installation Document, 15330 and or the panel's or annunciator's documentation.
Step 2. After the CAB3/CAB4 cabinet is prepared with the CHS-4L chassis installed, perform the
20
authority having jurisdiction or prepare an existing CAB-3/CAB-4 series cabinet that
houses a supported panel or annunciator. Refer to
panels and annunciators.
"NFN Gateway Hardware Installation" on page
1 General
All cabinets are fabricated from 16 gauge steel. The cabinet consists of two basic components: a backbox and a locking
door.
The key-locked door is provided with a pin-type hinge, two keys, and the necessary hardware to mount the door to the
backbox. The backbox has been engineered to provide ease-of-entry for the installer. Knockouts are positioned at
numerous points to let the installer bring conduit into the enclosure easily. Doors can be mounted on the left or right-hand
side. The same hinge works in both configurations, so that this choice can be made in the field. The door opens 180°.
Cabinets are available in four (4) sizes, A through D. The outside dimensions are noted on each enclosure diagram. "A"
size accommodates one chassis, a power supply, and two 26 AH batteries; "D" size accommodates four chassis, a power
supply, and two 26 AH batteries. A trim ring option is available for semi-flush mounting. The CAB-3/CAB-4 Series is
compatible with multiple chassis including the CHS-M2, CHS-M3, CHS-4, CHS-4L, CHS-4N, CHS-BH, CHS-PS, CA-1,
and CA-2. Note: CAB-4 series backboxes and doors are sold separately.
2 Before You Begin
opened when the door is at less than a 120° angle to the cabinet. If you are using the left-hand mounting option, be sure
that the door can open at least 120°. This is especially important if the cabinet is to be mounted in a closed area, such as a
closet or utility room.
3 Door Assembly Instructions
Hinges can be either left or right hand mounted. The Illustrations and text depict a left hand mounted example. For a right
hand mounting, simply substitute right for left in the instructions.
1.
2.
3.
Figure 2.3 CAB-3/CAB-4 Series Installation Document, 15330
NFN Gateway Installation & Operation Manual - P/N: 52306:Rev: D 06/01/07
Table 1.1 on page 7
21.
CAB-3/CAB-4 Series Cabinets
Product Installation Document
PN 15330:G 05/23/2005 05-310
The option of mounting doors in either a left/right hand configuration
will aid in installation and service when two control panels are
mounted in a confined area or side by side (as shown). In this manner
the doors can be opened "barn door" style, permitting an open work
space. Note that in this type of installation it is necessary to leave
enough space between cabinets to insert a key into the locks on the
door frames.
IMPORTANT: Attach the two hinges and two alignment tabs to the
backbox before any equipment is installed. With chassis installed,
space is very limited.
Display Interface Assembly Note: When the door is left-hand
mounted, the Display Interface Assembly (DIA) dress panel cannot be
Insert door hinges (A) into the top and bottom slots of the side to be hinged (in this case the LEFT side). Secure the
hinges to the studs in the backbox with the #8 hex nuts provided. Note that the small hole on the outer tab faces
outward.
Thread stud (B) into the BOTTOM hinge first. Thread from the bottom up. Place the grounding "star" washer on the
stud. Place the door's lower corner onto this stud. Placing the door on the lower stud first provides a place for the door
to rest while you complete the assembly.
Align the door on the backbox, so that the door sits directly under the top hinge. Thread remaining stud (B) into the
TOP hinge and through the hole in the top of the door. Your door should now swing freely.
CAB3/CAB4 Cabinet Installation
for list of supported