Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Duco DucoBox Focus Series
Summary of Contents for Duco DucoBox Focus Series
- Page 1 ENGLISH DucoBox Focus ENGLISH Product version 17xxxx and above Installation guide Step by step duco.tv instructions L2000631 (Revision J | 17.07.2019) L2000631 Installation guide for DucoBox Focus (Revision J | 17.07.2019)
-
Page 2: Table Of Contents
DUCO, HANDELSSTRAAT 19 VEURNE, B-8630 Vero Duco - Handelsstraat 19 - 8630 Veurne - Belgium tel +32 58 33 00 33 - fax +32 58 33 00 44 - info@duco.eu - www.duco.eu L2000631 Installation guide for DucoBox Focus (Revision J | 17.07.2019) -
Page 3: Introduction
0,65 = local demand control Air supply options: With Duco’s Demand-Controlled Natural Ventilation Systems a wide range of self-regulating (SR) ventilation louvres is available for the supply of fresh air� From standard self-regulating louvres which can be fitted in every kind of window or installation site, to louvres with sound absorbing qualities for projects where there is exposure to (mild) levels of noise, fire- resistant louvres, custom louvres for high-rise buildings, to ventilation and solar shading in a single product or electronically controlled louvres with preheating�... -
Page 4: Fitting
10 NIET TE MISSEN TIPS connections Keep down restriction� A non-return flap is De goede werking van uw Duco ventilatiesysteem is volledig afhankelijk van de keuze en uitvoeringskwaliteit van de afvoerleidingen! required when discharging into a manifold� Position it at least 30 cm away from the Duco- Box�... -
Page 5: Wiring
04.B Cabling diagram The DucoBox Focus is able to communicate with Duco slave components via a wireless (RF) or wired link� Both types of communi- cation can be combined in one system� Communication with non-Duco components is possible via the Switch Sensor or one of the connections on the optional Communication Print (see page 8)�... -
Page 6: Control Valves
Maximum number tery-powered component (= hop point)� Please refer to information sheet components in a of components single system RF communication (L8000018) at www�duco�eu for further information� Wired (cabled communication) DUCO WIRED Power supply 24 VDC Wired components can be daisy-chained (= recommended)� This means that a separate cable will not be required for each component�... -
Page 7: 05�B Pairing The Control Valves
ENGLISH 05.B Pairing the control valves The control valves are paired automatically to the DucoBox whenever ‘installer mode’ is activated (see “Pairing components” chap- ter)� 05.C Removing / replacing a control valve Taking control valve out temporarily Temporarily removing control valve Follow these steps to take a control valve out of the unit Short-press the valve button in order to drive it temporarily, e�g�... -
Page 8: Additional Control Options
ENGLISH 06 Additional control options 06.A Communication Print With the optional Communication Print you have the option of al- lowing the Duco ventilation systems to communicate via ModBus Ethernet Micro SD-card and/or ethernet� ModBus integration enables them to be linked to a building management system�... -
Page 9: Electronical Installation
ENGLISH 07 Electronical installation 07.A Installer / User mode To add components to the network, remove or replace, the system should be put in ‘Installer mode’� The LED on each component indicates the active mode of the component (see table in next section)� ‘Installer mode’... - Page 10 ENGLISH It is important that components are paired with the correct zone for this zonal operation� Components can be paired with the DucoBox Focus itself (controlling all zones) or with a control valve (controlling a single zone)� A component will be paired in every case with the component (control valve or DucoBox) that is flashing rapidly�...
-
Page 11: 07�D Removing / Replacing Components
• Restoring factory settings for the DucoBox and all paired components (AS FROM DucoBox version 18xxxx): Long-press ‘INST’ and ‘ENTER’ if not in ‘Installer mode’� The network remains in place� • Use the Duco Network Tool to read out information from components� L2000631 Installation guide for DucoBox Focus (Revision J | 17.07.2019) -
Page 12: Air Calibration
The system needs to be configured for it to work correctly� This will ensure its operation is as quiet as possible and energy-efficient� See under the Tools heading at www�duco�eu for information about determining ventilation flow rates� 08.A Air calibration procedure for DucoBox Focus The configuration procedure must be carried out on a calm day (no more than wind force 2: leaves rustling, feeling the wind in one’s face)�... -
Page 13: 08�B Checking
0.000 0.000 STEKKER_STOPCONTACT email: info @ duco.eu www.duco.eu This drawing is property of Vero Duco NV and can not be copied, neither shown to kg/m dm²/m mm³ third party/externally without written permission. * Depending on the software version of the User controller / CO /Humidity sensor�... -
Page 14: Maintenance & Service
All warranty conditions concerning the DucoBox and Duco's ventilation systems can be found on the Duco website� All complaints are to be reported to Duco by the Duco distributor with a clear description and the order/invoice number under which the products were delivered� In order to register the complaint, please use the complaint registration form found on the Duco website and the product's serial number in your message to service@duco�eu�... - Page 15 ENGLISH L2000631 Installation guide for DucoBox Focus (Revision J | 17.07.2019)
- Page 16 ENGLISH Installed by: L2000631 Document last modified on 17.07.2019 (revision J) L2000631 Installation guide for DucoBox Focus (Revision J | 17.07.2019)
Need help?
Do you have a question about the DucoBox Focus Series and is the answer not in the manual?
Questions and answers