Roland JUPITER-X Owner's Manual page 25

Parameter Value
Explanation
[1] knob [2] knob
Specifies the time from when the input to the
0.1, 1, 2,... 100
mic compressor exceeds the Comp Thres level
CompAttack
[ms]
until the volume is compressed.
Specifies the time from when the input to the
10, 10, ... 1000
mic compressor falls below the Comp Thres
CompRelease
[ms]
level until compression is no longer applied.
Specifies the level at which the mic compressor
CompThreshold -60–0 [dB]
starts applying compression.
1: 1, 2: 1, ...4: 1,
Specifies the compression ratio for the mic
8: 1, 16: 1, 32: 1,
CompRatio
compressor.
INF: 1
Smooths the transition until the mic
compressor starts to be applied.
0–30 [dB]
CompKnee
Higher values produce a smoother transition.
-24.0, -23.5, ... 0, Specifies the output volume of the mic
CompOutGain
..., +24.0 [dB] compressor.
Specifies the amount of reverb that is applied
0–127
Rev Send Lev
to the mic input.
Specifies the amount of chorus that is applied
0–127
Cho Send Lev
to the mic input.
Specifies the amount of delay that is applied to
0–127
Dly Send Lev
the mic input.
If you want the mic to be cut when the vocoder
OFF, ON
Mic Thru
is off, turn this "OFF. "
CONTROLLER
Specifies the velocity value that is transmitted
REAL, 1–127
Velocity
when you play the keyboard.
LIGHT, MEDIUM,
Specifies the keyboard touch.
Velo Crv
HEAVY
-10–+9 Adjusts the keyboard velocity curve.
Velo Offset
Specifies whether the parameter value
corresponding to a controller is immediately
updated when you operate that controller
DIRECT, CATCH
Knob Mode
(DIRECT) or only after the controller reaches
the same position as the parameter's current
value (CATCH).
0–100 Specifies the sensitivity of aftertouch.
Aft Sens
BUTTON Func
Specifies whether the functions assigned
to these buttons follows the settings of the
SCENE, SYS
Source
currently selected scene (SCENE) or the system
settings (SYS).
For the values, refer Specifies the function assigned to the S1
S1 Func
to Assignable Sheet. button.
LATCH,
Specifies how the button operates.
S1 Mode
MOMENTARY
For the values, refer Specifies the function assigned to the S2
S2 Func
to Assignable Sheet. button.
LATCH,
Specifies how the button operates.
S2 Mode
MOMENTARY
For the values, refer Specifies the function assigned to the S3
S3 Func
to Assignable Sheet. button.
LATCH,
Specifies how the button operates.
S3 Mode
MOMENTARY
SLIDER Func
Specifies whether the function assigned to the
SL1 slider follows the setting of the currently
SCENE, SYS
SL1 Source
selected scene (SCENE) or the system setting
(SYS).
For the values, refer Specifies the function assigned to the SL1
SL1
to Assignable Sheet. slider.
Specifies whether the function assigned to the
SL2 slider follows the setting of the currently
SCENE, SYS
SL2 Source
selected scene (SCENE) or the system setting
(SYS).
For the values, refer Specifies the function assigned to the SL2
SL2
to Assignable Sheet. slider.
Parameter Value
Explanation
[1] knob [2] knob
PEDAL Func
Specifies whether the function assigned to the
pedal connected to the HOLD jack follows the
SCENE, SYS
Hold Source
setting of the currently selected scene (SCENE)
or the system setting (SYS).
For the values, refer Specifies the function assigned to the pedal
Hold
to Assignable Sheet. connected to the HOLD jack.
STANDARD, Specifies the polarity of the pedal connected
Hold Pole
REVERSE to the HOLD jack.
Specifies whether the function assigned to the
pedal connected to the CTRL jack follows the
SCENE, SYS
Ctrl Source
setting of the currently selected scene (SCENE)
or the system setting (SYS).
For the values, refer Specifies the function assigned to the pedal
Ctrl
to Assignable Sheet. connected to the CTRL jack.
WHEEL Func
Specifies whether the function assigned to
the Wheel1 wheel follows the setting of the
SCENE, SYS
Wheel1 Source
currently selected scene (SCENE) or the system
setting (SYS).
For the values, refer Specifies the function assigned to the Wheel1
Wheel1
to Assignable Sheet. wheel.
Specifies whether the function assigned to
the Wheel2 wheel follows the setting of the
SCENE, SYS
Wheel2 Source
currently selected scene (SCENE) or the system
setting (SYS).
For the values, refer Specifies the function assigned to the Wheel2
Wheel2
to Assignable Sheet. wheel.
PART Btn Asgn
Assign the functions of the [1]–[5] ([6]–[10],
[11]–[15]) buttons and their functions when
pressed while holding down the [SHIFT]
button.
No Assign:
PartSel:
from the panel and in the screen. The part
played from the keyboard does not change.
Part+KeySw:
1-5
current part and the Keyboard SW, so that the
No Assign,
1-5+(S)
selected part can be played from the keyboard.
PartSel,
By pressing multiple parts simultaneously, you
6-10
Part+KeySw,
can turn Keyboard SW on for multiple parts.
6-10+(S)
KeySw, PartSw,
KeySw:
ArpSw, EfxSw
11-15
change the part played from the keyboard.
11-15+(S)
PartSw:
This is useful for DJ-like performances in which
you turn each part's sound on/off while you
perform.
ArpSw:
by the arpeggio.
Efx Sw:
REV, DLY, and CHO respectively on/off for all
parts simultaneously.
Settings for the Entire Unit
No assignment.
Specifies the current part operated
Simultaneously operates the
Functions as the keyboard switch to
Turns on/off the sound of each part.
Switches whether each part is played
From the left button, turns MFX, DRIVE,
25