Roland JUPITER-X Owner's Manual page 24

Settings for the Entire Unit
Parameter Value
[1] knob [2] knob
-12–0 [dB]
SPOut Gain
OFF, 30 [min],
Auto Off
240 [min]
0–31
LED On Bright
0–30
LED OffBright
1–10
LCD Contrast
OFF, ON
Scene Lock
01-01–16-16
Startup Scene
ARPEGGIO
OFF, ON
Set Tone
OFF, ON
Set Drumkit
OFF, ON
Set Tempo
OFF, BEAT,
Arp Sync (*1)
MEASURE
TEMPO/SYNC
20.00–300.00
Tempo
SCENE, SYS
Tempo Src
AUTO, INT, MIDI,
Sync Mode
USB
OFF, MIDI, USB,
Sync Out
MIDI/USB
BLUETOOTH
OFF, ON
Bluetooth Sw
-
Pairing
OFF, 1–9
Bluetooth ID
(*1) This is valid only if Sync Mode is "MIDI" or "USB. "
24
Explanation
Adjusts the output gain of the speakers.
Specifies whether the unit will turn off
automatically after a certain time has elapsed.
If you don't want the unit to turn off
automatically, choose "OFF" setting.
Adjusts the brightness when the LEDs are lit.
When the JUPITER-X is operating, you can make
the LEDs remain dimly lit when off instead of
going completely dark.
This setting adjusts the LED brightness when off.
Adjusts the contrast of the display.
Specifies whether a confirmation screen
appears when you recall a scene.
OFF:
The scene is recalled immediately.
ON:
Before the scene is recalled, a confirmation
screen appears. To recall the scene, use the
PAGE [<][>] buttons to select "Yes, " and then
press the [ENTER] button.
Specifies the scene that is recalled when the
unit starts up.
Specifies whether the current sound settings
are kept while only the phrase is switched
(OFF) or both the phrase and the sound
settings are switched (ON).
Specifies whether the current sound settings
are kept while only the rhythm is switched
(OFF) or both the rhythm and the sound
settings are switched (ON).
Specifies whether the current tempo setting is
kept while only the rhythm is switched (OFF)
or both the rhythm and the tempo settings are
switched (ON).
Specifies the synchronization setting for
arpeggio performance when connected to an
external device and playing in synchronization.
OFF:
Does not synchronize to measures or
beats. Arpeggio performance starts at the
moment that MIDI messages are received.
BEAT: Synchronizes to beats. Arpeggio
performance starts at the next beat after MIDI
messages are received.
MEASURE:
Synchronizes to measures.
Arpeggio performance starts at the first beat
of the next measure after MIDI messages are
received.
Specifies the system tempo.
When you switch scenes, this setting specifies
whether to use the system tempo (SYS) or the
tempo stored in the scene (SCENE).
Specifies the synchronization signal according
to which the JUPITER-X operates.
Specifies the connector from which MIDI clock
messages etc. are output.
Enables (ON) or disables (OFF) Bluetooth
communication.
Executing pairing for Bluetooth audio.
Specifies the number added to the end of
this unit's device name shown in a Bluetooth-
connected app.
Parameter Value
[1] knob [2] knob
MIDI
1–16, OFF
Ctrl Ch
SYS, SCENE
Ctrl Src Sel
SysCtrlSrc1
OFF, CC01-CC31,
SysCtrlSrc2
CC33-CC95,
SysCtrlSrc3
BEND, AFT
SysCtrlSrc4
OFF, ON
Soft Thru
OFF, ON
USB-MIDIThru
VENDOR,
USB Driver
GENERIC
OFF, ON
Remote Kbd
OFF, ON
Local Sw
17–32
Device ID
MIDI Tx
OFF, ON
Tx PC
OFF, ON
Tx Bank
OFF, ON
Tx Edit
MIDI Rx
OFF, ON
Rx PC
OFF, ON
Rx Bank
OFF, ON
Rx Exclusive
MIC IN
-24.0–+24.0 [dB]
Mic In Gain
0–1
Mic Power
OFF, ON
NS Switch
0–127
NS Threshold
0–127
NS Release
OFF, ON
CompSwitch
Explanation
Specifies the MIDI receive channel on which
MIDI messages (program change and bank
select) from an external MIDI device can be
received to switch programs.
If you don't want programs to be switched
from a connected MIDI device, turn this "OFF. "
SYS: SysCtrlSrc1–4 are used for tone control.
SCENE: The scene's CtrlSrc1–4 settings are
used for tone control.
Specify the MIDI messages that will be used as
system controls.
If this is ON, MIDI messages that are input
from the MIDI IN connector are re-transmitted
without change from the MIDI OUT connector.
Specifies whether MIDI messages received at
the USB COMPUTER port/MIDI IN connector are
retransmitted without change from the MIDI
OUT connector/USB COMPUTER port (ON) or
are not retransmitted (OFF).
Specifies the USB driver setting.
Turn this "ON" if you want to use an external
MIDI keyboard instead of the JUPITER-X's
keyboard. In this case, the MIDI transmit
channel of the external MIDI keyboard does
not matter.
Normally you will leave this "OFF. "
Turns on/off the connection between the
controller section (keyboard, PITCH, MODE,
panel buttons and sliders, pedals, etc.) and the
internal sound engine.
When transmitting and receiving system
exclusive messages, the device ID numbers of
both devices must match.
Specifies whether program change messages
will be transmitted (ON) or not be transmitted
(OFF).
Specifies whether bank select messages will be
transmitted (ON) or not be transmitted (OFF).
Specify whether changes you make in the
settings of a program will be transmitted as
system exclusive messages (ON), or will not be
transmitted (OFF).
Specifies whether program change messages
will be received (ON) or not be received (OFF).
Specifies whether bank select messages will be
received (ON) or not be received (OFF).
Specifies whether system exclusive messages
will be received (ON) or not be received (OFF).
Adjusts the input level of the MIC IN jack.
If this is "ON, " plug-in power (5 V) is supplied to
the MIC IN jack.
Switches the noise suppressor on/off.
The noise suppressor is a function that
suppresses noise during periods of silence.
Adjusts the volume at which noise suppression
starts to be applied.
Adjusts the time from when noise suppression
starts until the volume reaches 0.
Specifies whether the mic compressor (a
compressor applied to the mic input) is used
(ON) or not used (OFF).