Settings For The Entire Unit; Returning To The Factory Settings; "Factory Reset; Saving The System Settings - Roland JUPITER-X Owner's Manual

Settings for the Entire Unit

Returning to the Factory Settings

(Factory Reset)
Here's how the settings that you edited and saved on the JUPITER-X
can be returned to their factory-set condition.
* When you execute this operation, all saved settings including the sound
parameters will be lost.
* If you will later need the current settings, be sure to use the backup
function (p. 22) to save the current settings before you restore the
factory settings.
1.
Press the [MENU] button.
2.
Use the [1] knob to select
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select
the [ENTER] button.
A confirmation message appears.
If you decide to cancel, press the
4.
To execute, use the [2] knob
the [ENTER] button.
The display indicates "Completed. "
5.
Turn the power of the JUPITER-X off and then on again.
* Never turn off the power or disconnect the USB flash drive during a
process, such as while the "Executing..."

Saving the System Settings

1.
Press the [MENU] button.
2.
Use the [1] knob to select
[ENTER] button.
You can also make this selection by using the
instead of the [1] knob.
3.
Use the [1] knob to select the parameter and use the
knob to change the setting.
Saving the System Settings
1.
In the system setting screen, press the
A confirmation message appears.
If you decide to cancel, press the
2.
To execute, press the [ENTER]
"UTILITY," and then press the
PAGE [ ] [ ] buttons

"FACTORY RESET,"

and then press
[EXIT] button.
to select "OK," and then press
display is shown.
(System)

"SYSTEM,"

and then press the
PAGE [ ] [ ] buttons
[2]
(System Write)
[WRITE] button.
[EXIT] button.
button.
System parameter list
Parameter Value
Explanation
[1] knob [2] knob
AGING
Specifies whether the character of the sound
(pitch variance) changes according to the
varying internal temperature of this unit.
This has an effect only on analog synthesizer
models.
The internal temperature value is shown in the
upper right of the top screen of the scene.
OFF:
by the temperature. Nor is there a temperature
indication in the SCENE screen.
ON:
value specified by Aging Init Temp, and
changes to the actual temperature (REAL).
Although it depends on the temperature
OFF, ON, FAST,
Warm-Up
difference, the REAL temperature is reached
FIXED
in approximately ten minutes. After reaching
the REAL temperature, the setting follows the
actual temperature change.
FAST:
the value specified by Aging Init Temp, and
then quickly (in approximately ten seconds)
changes to the actual temperature (REAL)
when you play the keyboard. After reaching
the REAL temperature, the setting follows the
actual temperature change.
FIXED:
value specified by Aging Init Temp, and the
character of the sound is maintained at that
point.
Specifies the initial internal temperature for
Warm-Up.
REAL,
REAL:
0–60 [°C]/
Init Temp
measured will be the initial temperature.
32–140 [°F]
0–60°C/32–140°F:
internal temperature (Centigrade/Fahrenheit).
Simulates the aging of an analog synthesizer's
internal components. Increasing this value
OFF, changes the sound as it would be on a unit
Age
1–100 [years] that is a corresponding number of years old.
This is valid only for sounds of an analog
synthesizer model.
GENERAL
Adjusts the overall tuning.
415.3–466.2 [Hz]
MasterTune
The displayed value is the frequency of the A4
key (middle A).
Shifts the JUPITER-X's overall pitch range in
-24–24
MasKeyShift
semitone steps.
Specifies whether the scene's SCALE TUNE
OFF, ON
ScaleTuneSw
setting is enabled (ON) or disabled (OFF).
Adjusts the audio input level of the USB
USB In Lev 0–127
COMPUTER port.
Adjusts the audio output level to the USB
USB Out Lev 0–127
COMPUTER port.
0–127 Adjusts the input level of the AUX IN jack.
AuxIn/BT InLev
Specifies whether the audio input of the USB
COMPUTER port is mixed into the audio output
of the USB COMPUTER port.
OFF, ON
USB Audio Thru
If you don't want to output this audio, turn
this "OFF. "
Specifies whether the input of the AUX IN
jack is mixed into the audio output of the USB
COMPUTER port.
OFF, ON
AUXIN USB Thru
If you don't want to output this audio, turn
this "OFF. "
-12–0–+12 [dB] Adjusts the output gain of OUTPUT/PHONES.
Line Out Gain
Specifies whether sound is output from the
speakers. The AUTO setting operates as "OFF"
OFF, ON, AUTO
Speaker Sw
when headphones are connected and as "ON"
when headphones are not connected.
The character of the sound is not affected
The internal temperature starts at the
The internal temperature starts at
The internal temperature is fixed at the
The internal temperature that is actually
Virtually specifies the initial
23