Table of Contents
Advertisement
10.0 - PROGRAMMING
Only expert users should modify these settings to avoid malfunctions of the parking
!
!
Supply the display (turn
"ON"
the vehicle
!
P
ress and keep pressed for more than two seconds one of the two push-buttons on the display; the
previous programming mode will be displayed
F: Factory, standard adjustment , "Factory parameters".
C: Custom, user-chosen adjustment, "Custom Parameters".
Press the left left-button to go to the next
parameter.
When the parameter you want to modify is displayed, press one of the push-buttons and keep it
pressed until the display starts to blink; at this point you can modify the parameter.
Press the left push-button to increase the value
of the parameter (
the letter "C" will be displayed
when parameter has been modified
Press one of the two
push-buttons
on the control unit and keep it pressed for at least two seconds
to register the value.
The display will stop blinking and the selected parameter will be displayed.
Disengage reverse gear and cut supply to the display (turn "OFF" the vehicle) to exit the
Press the two push-buttons on the display and keep them pressed for more than two
!
seconds to reset all the factory settings (F).
PAGE 10 - INSTALLER MANUAL
system.
ignition key) and engage reverse gear.
.
Press the right push-button to go to the
previous parameter.
Press the right push-button to decrease the
value of the parameter (
the letter "C" will be
).
displayed when parameter has been modified
programming mode.
11.0 - SETTING OF PARAMETERS
Nr.
PARAMETER
01
Volume of buzzer
02
Detection range of front central sensors
03
Detection range of rear central sensors
04
Detection range of sides sensors
05
STOP zone of front sensors
06
STOP zone of rear sensors
07
Audible warning for front obstacles
08
Mounting of front control unit
09
Mounting of rear control unit
10
Display colour
11
Suppression of spare wheel indication
12
Number of speed signal pulses
13
Delay of front sensors deactivation
14
Service display (testing)
15
Connection of odometer wire
16
Front sensors sensitivity to detect obstacles
17
Rear sensors sensitivity to detect obstacles
Ref.1
: 0 deactivated, 1 low, 2 high.
Ref.2
: the display having only 2 numbers, the range will be indicated as 20 and 80 instead of 120 and
180.
Ref.3
: 0
standard detection (sensors position 1-2-3-4), 1 inverted detection (sensor position 4-3-2-1
Ref.4
: 1 red, 2 green, 3 blue, 4 amber, 5 white.
If a protruding part behind the vehicle (tow hitch, external spare wheel, etc.) creates
false obstacle indications, gradually increase the value of parameter 11 until the right
).
Ref.5
: i
ncrease the value (from 0 to 3) until the system no longer detects the external spare wheel
or the tow hitch
.
Ref.6
: 0 not activated, 1
wireless communication test
audible alert
", 3
self-learning of speed pulses
display
).
Ref.7
: 0 c
onnection of display cable
Ref.8
: 1 low, 2 standard, 3 high.
RANGE
0, 1, 2 (
Ref.1
)
From 50 to 95 cm
Not used
From 50 to 95 cm
From 35 to 50 cm
Not used
0, 1 (
Ref.2
)
0, 1 (
Ref.3
)
Not used
1, 2, 3, 4, 5 (
Ref.4
Not used
From 1.0 to 25.0
0 or from 10 to 60 sec. (
0, 1, 2, 3, 4 (
Ref.6
0,1 (
Ref.7
)
Not used
1, 2, 3 (
Ref.8
)
setting is reached.
, 2
speed indication and activation of "overspeed
, 4 d
isplay of software version (small number on
, 1 not used.
INSTALLER MANUAL - PAGE 11
SETTING
2
---
160
60
---
35
---
---
0
)
3
0
3.0
Ref.5
)
---
)
0
0
---
0
).
Advertisement
Table of Contents
