Table of Contents
Advertisement
2.2 - REAR SENSORS
The sensors are activated when reverse gear is engaged; an audible signal
downward arrow icon that lights up on the display will indicate the sensors are active
Obstacles are signaled by different audible tones and the lighting up of the relative detection zones
and distance on the display.
The faster the beeping, the closer the obstacle; a continuous tone indicates the obstacle is extremely
close to the bumper.
To deactivate the sensors (when reverse gear is engaged), simply press the push-button on the right
hand side of the display; the "OFF" sign will light up on the bottom part of the displayed vehicle and the
downward arrow will turn off to indicate the sensors are deactivated
To reactivate them, simply press the same button or disengage reverse gear and re-engage it.
3.0 - TROUBLESHOOTING GUIDE
3.1 - SLOW POWER SUPPLY SIGNAL
If, when the reverse gear id engaged, the battery level is too low to guarantee the accuracy of the
system,
the system activation signal will almost immediately sound (lower sound than usual) but the
sensors will not work.
When nominal tension is restored, the sensors will start working normally
3.2 - FAULTY SENSORS
If, when ignition is turned on or reverse gear is engaged, one of the sensors turns out to be inoperative
or not connected, the vehicle icon will light up on the display together with the arrow and the
inoperative sensor (or sensors).
The icon of the inoperative sensor will flash as long as reverse is engaged; the other sensors will
operate normally.
POSSIBLE CAUSE
Ice on sensors
Sensors mounted too low
Back part of sensors in contact with frame
Sensors detect external spare wheel
In areas with high RF disturbances, the antenna icon will light up on the display and a
The display will turn off after a few seconds and will light up again after the disturbances
If necessary, adjust the sensors sensitivity level (see chap. 11.0, setting of parameter -
PAGE 04 - USER MANUAL
.
.
Sensor 1
inoperative;
sensor icon
flashes.
3.3 - OTHERS
SOLUTION
Clean the sensors
Use the angle brackets (9 or 12) to tilt axe of sensors upwards
Create a separation between the sensors and the vehicle (at
least 2mm)
Modify the setting of parameter 11
ticking sound will be heard.
cease.
parameter 17).
warning and the
.
"STOP" ZONE ICON.
SENSORS
ACTIVATED
INDICATION ICONS.
SENSORS
DEACTIVATED
INDICATION ICONS.
REAR SENSORS
DETECTION ZONES
ICONS.
S
ETTING OF OVERSPEED INDICATOR,
SCROLLING AND SETTING OF FUNCTIONS
This procedure can only be done if the relative cable of the display wiring is connected
!
Turn the ignition
!
Enter in the programming mode (see chapters
and
set it by keeping one of the two display buttons pressed for about 3 sec.; by activating this
function the display and the speed value will light up every time speed exceeds 10 km/h.
!
Turn ignition key "OFF" then "ON" and increse speed
!
Look at the speed displayed; when the required threshold is reached to set the overspeed audible
alert, press the right-hand display button
!
A series of audible signals will now sound every time the vehicle exceeds the registered speed.
!
To deactivate this function press the left-hand display button when speed exceeds 15km/h; an
audible signal will indicate deactivation.
!
To reactivate this function and set another threshold, press the right-hand side button (even if the
speed is higher than the one actually set, the system will register this last value)
4.0 - DISPLAY
The following icons will be displayed according to operations.
ACTIVATION/DEACTIVATION OF SENSORS, TURNING
.
OFF OVERSPEED INDICATOR, SCROLLING AND
On every button press, the sensors will be
The downward arrow icon will be displayed when the
5.0 - SETTING OF OVERSPEED AUDIBLE ALERT
to the odometric signal of the vehicle; check with your installer.
"ON".
10.0 and 1
.
.
DISTANCE OF OBSTACLE
INDICATOR
.
PARAMETER.
STATUS (F or C) AND SETTING
OF PARAMETER
.
VEHICLE SPEED.
SOFTWARE VERSION.
AUDIBLE WARNINGS ON/OFF
ICON.
S
ETTING MODE
.
CONTROL UNITS/DISPLAY
SIGNAL RECEPTION TEST.
RF DISTURBANCES.
SETTING OF FUNCTIONS.
activated/deactivated.
sensors are activated
.
1.0), select parameter
14, select value 2
.
USER MANUAL - PAGE 05
Advertisement
Table of Contents
