Blaupunkt PP5.2 Owner's Manual page 6

Note: Please remove the battery (CR2025) insulation sheet before using the remote controller; the best working distance is
within 5 meters without obstacle in between; please try your best to aim the IR sensor during operation.
Power setting and battery charging.
There have built in rechargeable battery inside of this unit. Before play the speaker, please follow up below step to charge the
unit first.
1. Using the supplied USB cable to connect the DC 5V jack on the rear panel, and another terminal connect with supplied USB
DC power adaptor. Then plug on the DC power adaptor to AC power source.
2. During the charging, the rear panel red LED indicator will turn on, and will off after be fully charged (2~3 hours charging
time).
3. During the battery power playback mode, the unit will stop play and display off when the power is too low. Please connect
power for re-charging and playing.
Note:
Your battery will last longer if you following these simple guidelines for charging and storing.
a. For charging first time, charge it at least 10 hours. And the battery will provide the best performance after fully charge and
discharge 3 times. It is better to charge the unit after discharge completely, otherwise there may affect the battery's lifetime.
b. Recharge and store the unit within the temperature range of 5°C~35°C (40°F~95°F).
c. Do not charge (longer than 24 hours). Excessive charging or discharging may shorten the battery's life.
d. Due to prolong charging and discharging, the unit battery life will be affected and playback will be shorten. We cannot
guarantee the same playback consistently throughout and this is not include in our warranty and service.
e. During charging, you can play the music at the same time.
f. Please do not use it under the high humidity and temperature environment for long time.
g. Please turn off the speaker if long time not to use.
Unit power on
Slide the power switch to "on" position on rear panel to power on the unit, and slide to off position to power off (display off ).
Short press the power button on remote controller to standby on/off the unit. In case of you off the unit by side the power
switch on rear panel that you cannot power on the unit by remote controller because the power is cut off completely.
Time setting
Press the mode button repeatedly until enter to clock time interface. Long press (2 seconds) the mode button until hour's digits
flare on display, rotate the volume knob to adjust the hour setting, short press mode button to confirm and skip to minute
setting, rotate the volume knob to adjust it and press the play/pause button to finish the time setting.
In case of you power off the unit by remote controller, the clock time will show 15 seconds and disappear on display
automatically; short press any one button from panel or remote controller(except power button), the clock time will show 10
seconds on display in case of you need check the time.
Note: The clock time may reset in case of battery power exhausted, and without DC power connection. You may need set up it
again after charging.
FM RADIO
Before to do the FM reception, please extent the telescope FM antenna as long as it can be. Please place the unit next to window
for better reception. If the FM reception is not good, please try to move other place for reception.
FM play: Slide the power switch to "on' position on rear panel to power on the unit. There will have " HI" show on display and
skip to FM mode directly. Press and hold play/pause button 3 seconds, the unit will auto tune and save the FM radio station
automatically. Max support 60 preset stations. Short press the previous or next button will select and play previous or next
preset station. Press and hold previous or next button will auto scan the available FM station in forward or backward frequency.
Short press play/pause button will mute the unit. Rotate the volume knob to adjust the output volume level; Max volume is 30,
and default volume 18. Rotate the tuning knob to adjust the FM frequency by 0.1MHz each step.
FM operation by remote controller: press FM scan button shortly to start auto scan and station preset function automatically ,
repress it shortly to stop auto scan and play first preset station; press previous button shortly to decrease FM frequency by
0.1MHz each step, press previous button longer time to auto scan in backward, and stop till get the available station; press next
button shortly to increase FM frequency by 0.1MHz each step, press next button longer time to start auto scan forward, and
stop till get the available station.
Inputting 1 or 2 digits from the remote control's digits button part can get and play the preset stations. For example, there have
20 preset station ready in unit, if press 1 and 5 number from remote control, 0015 will display, then the unit will switch to "P15"
preset station and play. If you also input 3 digits or 4 digits from remote control, the unit will play and get the correspondence
FM frequency stations between 87.5-108MHz. For example, if you input 1043 from remote control, then 1043 will show on
display and play FM station frequency at 104.3MHz.
USB playback operation
Before start the USB playback operation, please insert the USB into the relative slot on the rear panel first, the unit only can
detect and playback the USB when there have available device in the slot. Slide the power switch to " on' position on rear panel
to power on the unit. The unit will read out and play the USB device automatically after show " HI" on display. While the USB
mode is playing, short press play/pause button for play/pause control; short press previous/next button for previous or next
track selection; press and hold previous/next button for fast backward or forward selection and resume play after release the
previous/next button.
4