Ubiquiti GBE Quick Start Manual
  1. Manuals
  2. Brands
  3. Ubiquiti Manuals
  4. Wireless Access Point
  5. GBE
  6. Quick start manual

Ubiquiti GBE Quick Start Manual

Hide thumbs Also See for GBE:
Table of Contents

Advertisement

Quick Links

Download this manual
7. 2. 2020
Package Contents
GBE
Metal Strap
Installation Requirements
Clear line of sight between GigaBeam AP and station
Pole-mounting: 7 mm socket wrench or screwdriver
Wall-mounting: wall fastener (not included)
Shielded Category 5 (or above) cabling with drain wire should be used for all wired
Ethernet connections and should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from harmful outdoor
environments and destructive ESD events with industrial-grade, shielded Ethernet
cable from Ubiquiti. For more details, visit
Surge protection should be used for all outdoor installations. We recommend that
you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device
and the other at the entry point to the building. The ETH-SP-G2 will absorb power
surges and safely discharge them into the ground.
Note:
local electrical regulatory codes.
https://dl.ui.com/qsg/GBE/GBE_EN.html
GBE Quick Start Guide
Ball Joint Mount
Gigabit PoE (24V, 0.5A) with
Mounting Bracket
For guidelines about grounding and lightning protection, follow your
GBE Quick Start Guide
ui.com/toughcable
Lock Ring
Power Cord
1/18

Advertisement

Table of Contents
loading

Related Manuals for Ubiquiti GBE

Summary of Contents for Ubiquiti GBE

  • Page 1 Ethernet connections and should be grounded through the AC ground of the PoE. We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit ui.com/toughcable Surge protection should be used for all outdoor installations. We recommend that you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and the other at the entry point to the building.

  • Page 2: Hardware Overview

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide Hardware Overview Reset Button To reset to factory defaults, press and hold the Reset button for more than 10 seconds while the device is powered on. Alternatively, the device may be reset remotely via a Reset button located on the bottom of the Gigabit PoE Adapter.

  • Page 3: Hardware Installation

    The LED will light steady blue when an active Ethernet connection is made to the Ethernet port and flash when there is activity. Power/Status LED Flashing White Bootup in progress. Ready for use, not connected to Ubiquiti® Network White Management System (UNMS™). See “UNMS Management”.

  • Page 4: Wall Mounting

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide Wall Mounting The device must be mounted directly to a wood stud or other structurally stable surface to avoid damage to the mounting hole when you adjust the aim.

  • Page 5: Installation Instructions

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide Note: Center screw included. Two optional screws (not included) provide additional stability. Installation Instructions https://dl.ui.com/qsg/GBE/GBE_EN.html 5/18...
  • Page 6 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide NanoBeam Wall Mount Kit Fastener (not included) Aiming Visually aim the GigaBeam radios at each other. https://dl.ui.com/qsg/GBE/GBE_EN.html 6/18...

  • Page 7: Connecting Power

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide Connecting Power https://dl.ui.com/qsg/GBE/GBE_EN.html 7/18...
  • Page 8 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide WARNING: The switch port must comply with the power specifications listed in “Specifications”. https://dl.ui.com/qsg/GBE/GBE_EN.html 8/18...
  • Page 9 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide Optional Configuration The device is set to DHCP by default, so it will try to automatically obtain an IP address. If that fails, it will use the default fallback IP address, 192.168.1.20. Proceed to the appropriate section, DHCP or “Fallback IP...
  • Page 10 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide 4. Enter a Username and Password, confirm the Password, and click Save. 5. Click the icon. 6. Configure the following settings: a. For one device, enable Access Point mode. For the other device (the Station), keep Access Point disabled.
  • Page 11 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide b. Review the Network settings to ensure that each device has a unique IP address. Each can get its IP address via DHCP, or use a static IP address.
  • Page 12 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide 5. Enter a Username and Password, confirm the Password, and click Save. 6. Click the icon. 7. Configure the following settings: a. For one device, enable Access Point mode. For the other device (the Station), keep Access Point disabled.

  • Page 13: Installer Compliance Responsibility

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide b. Review the Network settings to ensure that each device has a unique IP address. Each can get its IP address via DHCP, or use a static IP address.

  • Page 14: Specifications

    7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide The 5GHz Output Power field is provided to the professional installer to assist in meeting regulatory requirements. Specifications Dimensions 140 x 140 x 44 mm (5.51 x 5.51 x 1.73) Weight 376 g (13.3 oz)

  • Page 15: Safety Notices

    7. 2. 2020 GBE Quick Start Guide Operating Frequency (GHz) GBE Quick Start Guide Worldwide 5.180 - 5.875 57 - 66 US/CA U-NII-1 5.180 - 5.250 U-NII-3 5.725 - 5.850 57 - 66 Management Radio (MHz) Worldwide 2412 - 2472...

  • Page 16: Important Note

    7. 2. 2020 GBE Quick Start Guide Changes or modifications not expressly approved by the party responsible for compliance could GBE Quick Start Guide void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions.

  • Page 17: Declaration Of Conformity

    7. 2. 2020 GBE Quick Start Guide Cet émetteur ne doit être installé à proximité d’aucune autre antenne ni d’aucun autre GBE Quick Start Guide émetteur, et ne doit être utilisé conjointement à aucun autre de ces appareils. Australia and New Zealand Warning: This equipment is compliant with Class A of CISPR 32.
  • Page 18 7. 2. 2020 GBE Quick Start Guide GBE Quick Start Guide © 2020 Ubiquiti Inc. All rights reserved. https://dl.ui.com/qsg/GBE/GBE_EN.html 18/18...

Table of Contents