Related Manuals for Rice Lake RL-MPS-50
Summary of Contents for Rice Lake RL-MPS-50
- Page 1 Rice Lake Mechanical Physician Scal Model RL-MPS-50 Operation Manual November 12, 2019 PN 196007...
- Page 2 All information contained within this publication is, to the best of our knowledge, complete and accurate at the time of publication. Rice Lake Weighing Systems reserves the right to make changes to the technology, features, specifications and design of the equipment without notice.
-
Page 3: Table Of Contents
4.0 Specifications ............... . . 10 Technical training seminars are available through Rice Lake Weighing Systems. - Page 4 RL-MPS-50 Rice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit www.ricelake.com/webinars www.RiceLake.com Visit our website...
-
Page 5: Introduction
Introduction Introduction The Rice Lake Mechanical Physician Scale (RL-MPS-50) is ideal for use in health clinics and doctors’ practices for height and weight measurement. This manual guides the user through basic instructions on scale assembly and operation. Manuals and additional resources are available from the Rice Lake Weighing Systems website at www.ricelake.com... -
Page 6: Assembly
RL-MPS-50 Assembly Place the shipping container in an open area with room for unpacking. Carefully remove the RL-MPS-50 from the shipping container. When unpacking, ensure that all assembly parts are accounted for. Check the scale for any visible damage. If any parts were damaged in shipment, notify Rice Lake Weighing Systems and the shipper immediately. -
Page 7: Scale Assembly
7. Ensure the pillar is held firmly against the scale platform (there should be no space between the pillar and scale platform). 8. Place the four washers on each pillar stud. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 8: Rod Connection
RL-MPS-50 9. Secure the pillar to the scale platform by using the supplied U-type external hexagon wrench to tighten the pillar nuts on each pillar stud. Figure 2-4. Pillar Studs Placement 2.1.2 Rod Connection 1. Use the supplied hook tool to reach the eye on the larger hook at end of the internal steel rod inside the pillar. -
Page 9: Wheel Installation
4. Bring the scale to an upright position. 5. Move the scale by holding both sides of the pillar top, slightly tipping the front side of the platform away from the floor and pushing to the new location. © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 10: Height Rod Installation
RL-MPS-50 2.1.4 Height Rod Installation 1. Adjust the two screws on the pillar if necessary, leaving enough room to slide the plate of the height rod brackets into the space between the head of the screw and the pillar. 2. Place the slots of height rod brackets over the heads of both screws on the pillar and let the plates settle into place. -
Page 11: Operation
Operation Operation The following sections explain how to operate the RL-MPS-50. Zero Adjustment To ensure accurate weighments, a zero adjustment should be done to the scale after assembly is complete. To perform zero adjustment: 1. Ensure the scale is sitting on a level surface. -
Page 12: Weighing Instructions
RL-MPS-50 Weighing Instructions 1. Ensure the weigh beam is in either LB/KG mode. You can change from LB/KG by flipping the top and bottom beams. The beams are black for LB mode and white for KG mode. See Figure 3-3 Figure 3-4. -
Page 13: Height Rod Instructions
8. Rotate the headpiece back to the vertical position and adjust the height rod back to the rest position (i.e. the headpiece should be locked in place within the inner height rod and the inner rod should be at its lowest position). © Rice Lake Weighing Systems ● All Rights Reserved... -
Page 14: Specifications
RL-MPS-50 Specifications Scale Capacity 450 lb (200 kg) Scale Resolution 0.25 lb (100 g) Height Range 29.5'' - 78.75'' (75 – 200 cm) Height Divisions 0.25'' (5 mm) Platform Size 14.77'' x 10.83'' (375 x 275 mm) Overall dimensions 22.25'' (L) x 18.27'' (W) x 58.47'' (H) (565 x 464 x 1485 mm) Scale Weight 34.2 lb (15.5 kg) - Page 16 Specifications subject to change without notice. Rice Lake Weighing Systems is an ISO 9001 registered company. 230 W. Coleman St. • Rice Lake, WI 54868 • USA U.S. 800-472-6703 • Canada/Mexico 800-321-6703 • International 715-234-9171 • Europe +31 (0)26 472 1319...