Kipor Sinemaster IG3000 Operation Manual
Digital generator
Hide thumbs
Also See for Sinemaster IG3000:
- Operation manuals (42 pages) ,
- Operation manual (41 pages) ,
- Owner's manual (40 pages)
Subscribe to Our Youtube Channel
Related Manuals for Kipor Sinemaster IG3000
Summary of Contents for Kipor Sinemaster IG3000
- Page 1 WUXI KIPOR POWER CO., LTD. S I N E M A S T E R DIGITAL GENERATOR I G 3 0 0 0 I G L B 3 0 0 0...
- Page 2 PREFACE Thank you for purchasing a our generators. This manual covers operation and maintenance of the IG3000, IGLB3000 generator. All information in this publication is based on the latest product information available at the time of approval for printing. We reserves the right to make changes at any time without notice and without incurring any obligation.
-
Page 3: Table Of Contents
CONTENTS 1.SAFETY INSTRUCTIONS 2.SAFETY LABEL LOCATIONS 3.PRE-OPERATION CHECK 4.STARTING THE ENGINE 5.GENERATOR USE 6.STOPPING THE ENGINE 7.MAINTENANCE 8.TRANSPORTING/STORAGE 9.TROUBLESHOOTING 10.SPECIFICATIONS 11.WIRING DIAGRAM 12.FIXING PICTURE OF CASTER... -
Page 5: Safety Instructions
1. SAFETY INSTRUCTIONS WARNING Our generators are designed to give safe and depe- ndable service if operated according to instructions. Read and understand the Owner's Manual before op- erating the generator. Failure to do so could result in personal injury or equipment damage. WARNING Exhaust gas contains poisonous carbon monoxide. -
Page 6: Safety Label Locations
To ensure safe operation-- 2.SAFETY LABEL LOCATIONS WARNING Gasoline is extremely flammable and explosive under certain conditions. 2.1 Outside view Refuel in a well ventilated area with the engine stopped. Keep away from cigarette, smoke and sparks when refueling the generator. Always refuel in a well-ventilated location. -
Page 7: Pre-Operation Check
2.2 Control panel 3.PRE-OPERATION CHECK SMART throttle switch Be sure to check the generator on a level surface with the engine stopped. DC receptacle 3.1 Check the engine oil level. AC receptacle Output indicator light (Green) CAUTION Overload indicator light (Red) Oil alarming indicator (Red) Using nondetergent oil or 2-stroke engine oil could shorten the engine's service life. - Page 8 Gasolines containing alcohol CAUTION If you decide to use a gasoline containing alcohol(gasohol), be sure its octance Running the engine with insufficient oil can cause serious engine damage. rating is at least as high as that recommended by us. There are two types of The Low Oil Alarm System will automatically stop the engine before the oil "gasohol": one containing ethanol, and the other containing methanol.
-
Page 9: Starting The Engine
4.3 Insert the engine key, and turn the engine switch to ON position. 4. STARTING THE ENGINE CAUTION CAUTION When starting the generator after adding fuel for the first time, after START longterm storage, or after running out of fuel, turn the fuel valve lever to the "ON"... -
Page 10: Generator Use
4.5 Push the choke knob to the OPEN position as the engine warms 5.GENERATOR USE up, see page 10. WARNING To prevent electrical shock from faulty appliances, the generator should be grounded. Connect a length of heavy wire between the generator's ground terminal and an external ground source. - Page 11 5.1 AC applications 5.3 DC application 1.Start the engine and make sure the output indicator light (green) comes on. The DC receptacle may be used for charging 12 volt automotive-type batteries only. 2.Confirm that the appliance to be used is switched off, and plug in the appliance. Output voltage is 15-30V when current receptacle on no load.
-
Page 12: Stopping The Engine
2. Start the engine 7.MAINTENANCE The DC receptacle may be used while the AC power is in use. An overloaded DC circuit will trip the DC circuit protector (push button comesout). If this happens, wait a few minutes before pushing in the circuit protector to The purpose of the maintenance and adjustment schedule is to keep the resume operation. - Page 13 7.2 Changing oil 1.Revolve the left side cover knob, open the left side maintenance cover. Drain the oil while the engine is still warm to assure rapid and complete draining. 2.Unsnap the clips, remove the air cleaner cover. 3.Foam element: Remove the foam element from the air cleaner cover.
- Page 14 7. Install the spark plug carefully, by hand, to avoid cross-threading. 7.5 Spark plug service 8. After a new spark plug has been seated by hand, it should be tightened 1/2 turn Recommended spark plug: F6RTC To ensure proper engine operation, the spark plug must be properly gapped and with a wrench to compress its washer.
-
Page 15: Transporting/Storage
7.6 Spark arrester maintenance 8.TRANSPORTING/STORAGE 8.1 When transporting the generator, turn the fuel valve lever OFF and keep the generator level to prevent fuel spillage. Fuel vapor or spilled fuel may ignite. Back cover 8.2 Before storing the unit for an extended period: Spark arrester 1.Be sure the storage area is free of excessive humidity and dust. -
Page 16: Troubleshooting
Appliance does not operate: 9.TROUBLESHOOTING Is the output indicator light ON? When the engine will not start: Refill the fuel tank. Is there fuel in the tank? Take the generator to an Is the overload indicator light ON? authorized dealer. Turn the engine switch on. -
Page 17: Specifications
10. SPECIFICATIONS 11. WIRING DIAGRAM Model IG3000/IGLB3000 Rated frequency (Hz) Yellow/Green Rated voltage (V) Rated current (A) 12.2 23.3 11.7 Rated speed (rpm) 3600 Rated output (kVA) Max output (kVA) DC output DC voltage High pressure wrap 12V-8.3A Electric circuit breaker Without Spark plug Single phase... -
Page 18: Fixing Picture Of Caster
12. FIXING PICTURE OF CASTER A. Disassemble the chassis setting beam a. Remove the bolt M8X16. b. Demount the chassis setting beam. 1. Chassis setting beam. 2. Bolt B. Installing the caster wheel parts a. Put a big gasket at each caster, and put them on the axle b.
Need help?
Do you have a question about the Sinemaster IG3000 and is the answer not in the manual?
Questions and answers