Should you detect any errors or inaccuracies in the manual, we would be grateful if you would inform us. This helps us to further improve our documentation. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
(Re)place the jerrycan with bubble fluid 3.3 (Re)place the jerrycan with smoke fluid 3.4 Configure Manual mode 3.5 Bubble in Manual mode Connect power and setup DMX Setup multiple machines in a sequence with DMX 3.8 Bubble with DMX Clean up 3.10 Clean the launch fans (when needed) Maintenance Troubleshooting Correct disposal EC Declaration of Conformity MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
(optionally filled with smoke) into the air with a capacity of 6 000 bubbles a minute. The MAGICFX SMOKEBUBBLE BLASTER pumps bubble fluid from a jerrycan to the ® bubble heads. The bubble fluid leaves a bubble head through the double-walled exterior.
FLIGHTCASE DISPLAY WITH BUTTONS AND LED INDICATORS FX LED INDICATOR BUBBLE CABINET SMOKE CABINET ON/OFF SWITCH (RESETTABLE FUSE) DMX INPUT & OUTPUT (5-POLE) POWER INPUT & OUTPUT (220 240 Vac) MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
FX FLUIDS The MAGICFX SMOKEBUBBLE BLASTER uses bubble fluid and smoke fluid from MAGIC ® FX to create smoke bubbles. The fluids are delivered in jerrycans. The 20 litre jerrycan with bubble fluid is placed and connected in the bubble cabinet, see Section 3.2. The 5 litre jerrycan with smoke fluid is placed and connected in the smoke cabinet, see Section 3.3.
PREV NEXT SELECT Display panel The display panel is located on the backside of the MAGICFX SMOKEBUBBLE BLASTER. ® Check the following menu structure for all options in the menu. Use the buttons for navigation and selection. The left-hand LED blinks red when DMX is active. The right- hand LED continuously lights red when an error is present.
Page 10
Output Distance (0–255) Display Dimmer (ON/OFF) (dims after 30 seconds of button inactivity) Factory Defaults (YES/NO) Configuration Wiper position right (190–240)* Wiper position left (370–420)* Error History Type (Alarm/Error) continues on next page MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
For RDM you will need a RDM compatible controller. The following RDM parameters are supported by the MAGICFX SMOKEBUBBLE BLASTER. ® Parameter ID Discovery DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE DEVICE_INFO SUPPORTED_PARAMETERS SOFTWARE_VERSION_LABEL DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL SLOT_DESCRIPTION DMX_PERSONALITY_DESCRIPTION DMX_START_ADDRESS IDENTIFY_DEVICE MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 12
Parameter ID Discovery DEVICE_LABEL FACTORY_DEFAULTS DMX_PERSONALITY RESET_DEVICE RDM parameters RDM parameters are subject of change due to software updates. Contact MAGIC FX for the latest information and updates. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Ensure sufficient lighting of the surroundings. • Keep the workplace clean. INDOOR USE The MAGICFX SMOKEBUBBLE BLASTER is designed for outdoor use and use in well- ® ventilated indoor spaces. Do not use the MAGICFX SMOKEBUBBLE BLASTER in poor ®...
Missing or obscured safety symbols on the machine can lead to WARNING death, serious injury or property damage. Make sure all safety symbols are correctly in place and visible, see Section 2.4. Always create a safety zone of 5 m in front of the MAGICFX ® WARNING SMOKEBUBBLE BLASTER.
LET’S BUBBLE! INSTALL THE MACHINE Bring the cased MAGICFX SMOKEBUBBLE BLASTER to the desired location. ® Unlock and remove the top cover. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Unlock and remove the side covers. Take the necessary safety precautions, see Section 2.5. Place the MAGICFX SMOKEBUBBLE BLASTER in its final position and set the ® brakes. (RE)PLACE THE JERRYCAN WITH BUBBLE FLUID Always follow the instructions as noted on the jerrycans. WARNING The bubble cabinet is equipped with a light. Switch the light on to NOTICE see the fluid levels in the jerrycans clearly.
Page 17
Make sure that the machine is not in operation (FX LED indicator is dimmed). Open the bubble cabinet door. Disconnect and remove an empty jerrycan if present. Place a jerrycan with bubble fluid in the bubble cabinet and remove and save the lid. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 18
Connect the bubble lid inside the cabinet. Close the bubble cabinet door. In case of multiple machines: Repeat steps 1 – 5 for each machine. 18 MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Make sure that the machine is not in operation (FX LED indicator is dimmed). Open the smoke cabinet door. Disconnect and remove an empty jerrycan if present. Place a jerrycan with smoke fluid in the smoke cabinet and remove and save the lid. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 20
Connect the smoke lid inside the cabinet. Close the smoke cabinet door. In case of multiple machines: Repeat steps 1 – 5 for each machine. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
3. Enjoy the view! 4. To stop blasting bubbles: • Set Manual mode to OFF, or; • Switch the machine OFF (next time you switch the machine ON, it starts bubbling again instantly). MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
8. Optionally see Section 3.7 for adding more machines to the same sequence. Always plug in a DMX Terminator into the DMX output. Using a CAUTION DMX Terminator improves signal reliability. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
8. Repeat step 1 – 5 for each subsequent machine. Always plug in a DMX Terminator into the DMX output of the final CAUTION unit in the control sequence. Using a DMX Terminator improves signal reliability. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
CLEAN UP Walk carefully when approaching the machine. The floor can be CAUTION slippery due to spilled bubble fluids. Make sure that the machine is not blasting bubbles. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 25
Open the bubble cabinet door. Disconnect the bubble lid from the jerrycan. Remove the jerrycan with bubble fluid and close off with the original lid. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 26
Fill up an empty jerrycan with hand warm water and place it in the bubble cabinet. Connect the bubble lid inside the cabinet. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 27
Set Manual mode to OFF and switch the machine OFF. Disconnect all DMX and power cable(s). Disconnect and remove the jerrycan. Connect the bubble lid inside the cabinet. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 28
Wipe down the machine with hand warm water and a cloth. Clean the floor in front of the machine. Position the wiper of each bubble head to the right side. Remove each bubble head. 10 x 28 MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 29
Remove the inner ring from each bubble head. 10 x Remove the drip tray and wipe down the drip cabinet with a damp cloth. Clean the bubble heads, inner rings and the drip tray with hand warm water. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 30
Remove the drip tray and wipe down the drip cabinet with a damp cloth. Replace the inner ring for each bubble head. Make sure that the inner ring is outlined correctly with the bubble head with the notch down. 10 x MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 31
Place and turn each bubble head back in place. 10 x Place and lock the side covers. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Page 32
Place and lock the top cover. Release the brakes. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
Remove a launch fan cover. Clean the fan interior and the fan blades with a cloth. Place the fan cover and fasten with the screws. Repeat steps 2 to 4 for the other launch fan. MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...
MAINTENANCE To achieve the maximum service life of the MAGICFX SMOKEBUBBLE BLASTER you ® must regularly clean the MAGICFX SMOKEBUBBLE BLASTER and test if it is functioning ® correctly. Contact MAGIC FX if the MAGICFX SMOKEBUBBLE BLASTER is not functioning correctly.
Translation of the original declaration of conformity Name manufacturer : MAGIC FX B.V. Address : Schouwrooij 27, 5281 RE BOXTEL Country : The Netherlands : B. Veroude Date : 22-2-2018 Signature MAGICFX SMOKEBUBBLE BLASTER — User and Installation Manual ®...