Subscribe to Our Youtube Channel
Related Manuals for NXP Semiconductors MIMXRT1010 EVK
Summary of Contents for NXP Semiconductors MIMXRT1010 EVK
- Page 1 NXP Semiconductors Document identifier: MIMXRT1010EVKHUG User's Guide Rev. 0, 30/07/2019 MIMXRT1010 EVK Board Hardware User’s Guide...
-
Page 2: Table Of Contents
2.13 User Interface LED Indicator............................ 13 Chapter 3 PCB Information................14 Chapter 4 EVK Design Files................15 Chapter 5 Contents of the Evaluation Kit............16 Chapter 6 Revision history................17 MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 3: Chapter 1 Introduction
This EVK board is a platform designed to showcase the most commonly used features of the i.MX RT1010 Processor in a small, low cost package. The MIMXRT1010 EVK board is an entry level development board, which gives the developer the option of becoming familiar with the processor before investing a large amount or resources in more specific designs. -
Page 4: Mimxrt1010 Evk Contents
The MIMXRT1010 EVK contains the following items: • MIMXRT1010 EVK Board • USB Cable (Micro B) 1.3 MIMXRT1010 EVK Board revision history • Rev A: Prototype. • Rev B: Prototype • Rev C: Pilot. MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 5: Chapter 2 Specifications
This chapter provides detailed information about the electrical design and practical considerations of the EVK Board, and is organized to discuss each block in the following block diagram of the EVK board See Figure Figure 1. Block diagram MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 6: I.mx Rt1010 Processor
Specifications Figure 2. Overview of the MIMXRT1010 EVK Board (Front side) The overview of the MIMXRT1010 EVK Board is shown in Figure 2.1 i.MX RT1010 Processor The i.MX RT1010 is a new processor family featuring NXP's advanced implementation of the ARM Cortex-M7 Core. It provides high CPU performance and best real-time response. -
Page 7: Boot Mode Configurations
The device has four boot modes (one is reserved for NXP use). The boot mode is selected based on the binary value stored in the internal BOOT_MODE register. Switch (SW8-3 & SW8-4) is used to select the boot mode on the MIMXRT1010 EVK Board. - Page 8 Specifications Figure 3. Power Tree The power control logic of the MIMXRT1010 EVK board is shown in Figure • It will power up SNVS , and then PMIC_REQ_ON will be switched on to enable external DC/DC to power up other power domains.
- Page 9 VDD_HIGH_IN VDD_HIGH_IN supply voltage Power for DCDC DCDC_IN Power for SNVS and VDD_SNVS_IN USB_OTG1_VBUS Power for USB VBUS Power for 12-bit ADC VDDA_ADC NVCC_GPIO IO power for GPIO MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors...
-
Page 10: Qspi Flash
Specifications 2.4 QSPI Flash A 128 Mbit QSPI Flash is used on the MIMXRT1010 EVK Board. If the developer wants to boot from the QSPI Flash, the boot device switch(SW8) settings should be: OFF, OFF, ON, OFF, as shown in Table 2.5 USB PHY Connector... -
Page 11: Arduino And Motor Control Expansion Port
A1/ADC1 A0/ADC0 Table 7. D0/UART_RX D1/UART_TX ENC_I D2/INT0 D3/INT1/PWM/OC2B D4/T0/XCK D5/TI/PWM D6/AIN0/PWM/OC0A D7/AIN1/PWM Table 8. CUR_A D8/CLKO/ICP1 CUR_B D9/OC1A/PWM CUR_C D10/SPI_CS VOLT_DCB D11/OC2A/PWM/SPI_MOSI Table continues on the next page... MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 12: On/Off Button
2.10 ON/OFF Button SW2 is the ON/OFF button for MIMXRT1010 EVK Board. A short pressing in OFF mode causes the internal power management state machine to change state to ON. In ON mode, a short pressing generates an interrupt (intended to be a software- controllable(power-down). -
Page 13: User Button
There are four LED status indicators located on the EVK Board. The functions of these LEDs include: • Main Power Supply(D27) Green: DC 5V main supply is normal. Off: the board is not powered. • Reset RED LED(D7) • OpenSDA LED(D5) • USER LED(D25) MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 14: Chapter 3 Pcb Information
PCB Information Chapter 3 PCB Information The MIMXRT1010 EVK Board is made using standard 2-layer technology. The material used was FR-4. The PCB stack-up information is shown in Table Table 10. Board stack-up information Layer Description Copper(Oz) Dielectric Thickness(mil) Signal, Power, GND... -
Page 15: Chapter 4 Evk Design Files
Chapter 4 EVK Design Files The schematics, layout files, and gerber files (including Silkscreen) can be downloaded from nxp.com/MIMXRT1010-EVK(waiting for update). MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 16: Chapter 5 Contents Of The Evaluation Kit
Chapter 5 Contents of the Evaluation Kit Table 11. EVK contents Item Description EVK Board EVK Board with processor, memory, interfaces, etc USB Cable USB cable (Micro-B to Standard-A) MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... -
Page 17: Chapter 6 Revision History
Chapter 6 Revision history Below table summarizes the changes made to this document since the initial release. Table 12. Revision history Revision number Date Substantive changes 07/2019 Initial release MIMXRT1010 EVK Board Hardware User’s Guide, Rev. 0, 30/07/2019 NXP Semiconductors... - Page 18 How To Reach Us Information in this document is provided solely to enable system and software implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to Home Page: design or fabricate any integrated circuits based on the information in this document. NXP nxp.com reserves the right to make changes without further notice to any products herein.
Need help?
Do you have a question about the MIMXRT1010 EVK and is the answer not in the manual?
Questions and answers