Subscribe to Our Youtube Channel
Related Manuals for NXP Semiconductors MIMXRT1015
Summary of Contents for NXP Semiconductors MIMXRT1015
- Page 1 NXP Semiconductors Document identifier: MIMXRT1015EVKHUG User's Guide Rev. 0, 27 March 2020 MIMXRT1015 EVK Board Hardware User’s Guide...
-
Page 2: Table Of Contents
2.13 User Interface LED Indicator....................12 Chapter 3 PCB Information..................13 Chapter 4 EVK Design Files................14 Chapter 5 Contents of the Evaluation Kit.............15 Chapter 6 Revision history...................16 MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 2 / 17... -
Page 3: Chapter 1 Introduction
This EVK board is a platform designed to showcase the most commonly used features of the i.MX RT1015 Processor in a small, low cost package. The MIMXRT1015 EVK board is an entry level development board, which gives the developer the option of becoming familiar with the processor before investing a large amount or resources in more specific designs. -
Page 4: Mimxrt1015 Evk Contents
• MIMXRT1015 EVK Board • USB Cable (Micro B) 1.3 MIMXRT1015 EVK Board revision history • Rev A: Pilot. • Rev B: Mass Product. MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 4 / 17... -
Page 5: Chapter 2 Specifications
This chapter provides detailed information about the electrical design and practical considerations of the EVK Board, and is organized to discuss each block in the following block diagram of the EVK board See Figure Figure 1. Block diagram MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 5 / 17... -
Page 6: I.mx Rt1015 Processor
The device has four boot modes (one is reserved for NXP use). The boot mode is selected based on the binary value stored in the internal BOOT_MODE register. Switch (SW8-3 & SW8-4) is used to select the boot mode on the MIMXRT1015 EVK Board. -
Page 7: Power Tree
NOTE For more information about boot mode configuration, see the System Boot chapter of the MIMXRT1015 Reference Manual. For more information about MIMXRT1015 EVK boot device selection and configuration, see the main board schematic. 2.3 Power Tree J41 and J9 can be used to supply the EVK Board. A DC 5V external power supply also can be used to supply the EVK Board by connecting two pins in J1. - Page 8 Specifications Figure 3. Power Tree The power control logic of the MIMXRT1015 EVK board is shown in Figure • It will power up SNVS , and then PMIC_REQ_ON will be switched on to enable external DC/DC to power up other power domains.
- Page 9 Power for DCDC DCDC_IN Power for SNVS and VDD_SNVS_IN USB_OTG1_VBUS Power for USB VBUS Power for 12-bit ADC VDDA_ADC NVCC_GPIO IO power for GPIO MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 9 / 17...
-
Page 10: Qspi Flash
Specifications 2.4 QSPI Flash A 128 Mbit QSPI Flash is used on the MIMXRT1015 EVK Board. If the developer wants to boot from the QSPI Flash, the boot device switch(SW8) settings should be: OFF, OFF, ON, OFF, as shown in Table 2.5 USB PHY Connector... -
Page 11: Arduino And Motor Control Expansion Port
2.10 ON/OFF Button SW2 is the ON/OFF button for MIMXRT1015 EVK Board. A short pressing in OFF mode causes the internal power management state machine to change state to ON. In ON mode, a short pressing generates an interrupt (intended to be a software- controllable(power-down). -
Page 12: User Button
SW4 is the USER Button (GPIO_EMC_09) to use by the developers. Press the button to produce changes in high and low levels. 2.13 User Interface LED Indicator • Reset RED LED(D21) • OpenSDA LED(D20) • USER LED(D25,D26,D27) MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 12 / 17... -
Page 13: Chapter 3 Pcb Information
NXP Semiconductors Chapter 3 PCB Information The MIMXRT1015 EVK Board is made using standard 2-layer technology. The material used was FR-4. The PCB stack-up information is shown in Table Table 7. Board stack-up information Layer Description Copper(Oz) Dielectric Thickness(mil) Signal, Power, GND... -
Page 14: Chapter 4 Evk Design Files
NXP Semiconductors Chapter 4 EVK Design Files The schematics, layout files, and gerber files (including Silkscreen) can be downloaded from https://www.nxp.com/design/ development-boards/i.mx-evaluation-and-development-boards/i.mx-rt1015-evaluation-kit:MIMXRT1015-EVK . MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 14 / 17... -
Page 15: Chapter 5 Contents Of The Evaluation Kit
Contents of the Evaluation Kit Table 8. EVK contents Item Description EVK Board EVK Board with processor, memory, interfaces, etc USB Cable USB cable (Micro-B to Standard-A) MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 15 / 17... -
Page 16: Chapter 6 Revision History
Below table summarizes the changes made to this document since the initial release. Table 9. Revision history Revision number Date Substantive changes 03/2020 Initial release MIMXRT1015 EVK Board Hardware User’s Guide, Rev. 0, 27 March 2020 User's Guide 16 / 17... - Page 17 How To Reach Us Information in this document is provided solely to enable system and software implementers to use NXP products. There are no express or implied copyright licenses granted hereunder to Home Page: design or fabricate any integrated circuits based on the information in this document. NXP nxp.com reserves the right to make changes without further notice to any products herein.
Need help?
Do you have a question about the MIMXRT1015 and is the answer not in the manual?
Questions and answers