1. Manuals
  2. Brands
  3. Elitegroup Computer Systems Manuals
  4. Motherboard
  5. P6VXM2T
  6. Manual

Elitegroup Computer Systems P6VXM2T Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Copyright
This publication, including all photographs, illustrations and software,
is protected under international copyright laws, with all rights re-
served. Neither this manual, nor any of the material contained herein,
may be reproduced without written consent of the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice.
The manufacturer makes no representations or warranties with re-
spect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose.
The manufacturer reserves the right to revise this publication and to
make changes from time to time in the content hereof without obliga-
tion of the manufacturer to notify any person of such revision or
changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Mi-
crosoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered
trademarks of Intel Corporation.
Other product names used in this manual are the properties of their
respective owners and are acknowledged.
Preface

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the P6VXM2T and is the answer not in the manual?

Questions and answers

Related Manuals for Elitegroup Computer Systems P6VXM2T

Summary of Contents for Elitegroup Computer Systems P6VXM2T

  • Page 1 Preface Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights re- served. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Version 1.0 Disclaimer The information in this document is subject to change without notice.
  • Page 2 Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen- erates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
  • Page 3 Declaration of Conformity This device complies with part 15 of the FCC rules. Operation is sub- ject to the following conditions: − This device may not cause harmful interference, and − This device must accept any interference received, includ- ing interference that may cause undesired operation. Canadian Department of Communications This class B digital apparatus meets all requirements of the Cana- dian Interference-causing Equipment Regulations.
  • Page 4 About the Manual The manual consists of the following: Chapter 1 Describes features of the main- board, and provides a shipping Introducing the Mainboard checklist. ⇒ Go to page 1 Chapter 2 Describes installation of main- board components. Installing the Mainboard ⇒...

  • Page 5: Table Of Contents

    Preface CHAPTER 1 Introducing the Mainboard Introduction ................1 Checklist................... 2 Standard Items ....................2 Features ................... 3 Mainboard Components ............. 5 Choosing a Computer Case ............7 CHAPTER 2 Installing the Mainboard Safety Precautions ..............8 Quick Guide ................9 Checking Jumper Settings ............
  • Page 6 Standard CMOS Features ................39 Advanced BIOS Setup Option..............42 Advanced Chipset Features Option............46 Integrated Peripherals Option ..............50 Power Management Setup Option............. 54 PNP/PCI Configuration Option ..............60 PCI Health Status Option................62 Frequency/Voltage Control................. 63 Load Fail-Safe Defaults Option..............64 Load Optimized Defaults Option ..............

  • Page 7: Introducing The Mainboard

    The mainboard accommodates PC 100/133 SDRAM (Syn- chronous DRAM) up to 1 GB using two 3.3V unbuffered DIMM modules. The P6VXM2T also has a full set of I/O ports, such as dual channel IDE interfaces, a floppy controller, two FIFO...

  • Page 8: Checklist

    Compare the mainboard’s package contents with the following checklists: Standard Items • One mainboard • One diskette drive ribbon cable and bracket • One IDE drive ribbon cable and bracket • One auto-install software support CD • This user’s manual...

  • Page 9: Features

    168-pin, 3.3V non-buffered DIMM memory modules. The DIMM memory modules can be SDRAM or VCM memory chips. The P6VXM2T includes a 4xAGP slot that pro- vides four times the bandwidth of the original AGP specification. AGP technology provides a direct...
  • Page 10 One 8/16-bit ISA slot (optional) • Two IDE channels and a floppy disk drive interface The P6VXM2T supports Ultra DMA bus mastering with transfer rates of 33/66/100 MB/sec. Integrated I/O The mainboard has a full set of I/O ports and con- nectors: •...
  • Page 12 Table of Mainboard Components Component Description AGP1 Accelerated Graphics Port ATX1 Standard 20-pin ATX power connector Three volt realtime clock battery CPUFAN1 Power connector for CPU cooling fan Audio connector for CD-ROM/DVD drive Auxiliary connector for CD-ROM/DVD drive CNR1 Communications Networking Riser slot (CNR supports modem and audio only) CPU Socket CPU Socket (PGA370)

  • Page 13: Choosing A Computer Case

    There are many types of computer cases on the market. The mainboard complies with the specifications for the Micro ATX system case. Some features on the mainboard are imple- mented by cabling connectors on the mainboard to indicators and switches on the system case. Ensure that your case sup- ports all the features required.

  • Page 14: Installing The Mainboard

    Installing the Mainboard Follow these safety precautions when installing the mainboard: • Wear a grounding strap attached to a grounded device to avoid damage from static electricity. • Discharge static electricity by touching the metal case of a safely grounded object before working on the mainboard.

  • Page 15: Quick Guide

    This Quick Guide suggests the steps you can take to assem- ble your system with the mainboards. The following table provides a reference for installing specific components: Locating Mainboard Components Go to page 5 Setting Jumpers Go to page 10 Installing the Mainboard in a Case Go to page 14 Installing Case Components...

  • Page 16: Checking Jumper Settings

    This section explains how to set jumpers for correct configura- tion of the mainboard. Setting Jumpers Use the mainboard jumpers to set system configuration op- tions. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

  • Page 17: Checking Jumper Settings

    Checking Jumper Settings The following illustration shows the location of the mainboard jumpers. Pin 1 is labeled.

  • Page 18: Jumper Settings

    Jumper Settings Jumper Type Description Setting (default) 3-pin Clear CMOS 1-2: Normal 2-3: Clear CMOS JP3~JP6 12-pin CPU Clock Refer to next Ratio page 2-pin BIOS flash Short: Enable protection Open: Disable JP10 3-pin AC power 1-2: Enable JP10 resume 2-3: Disable Jumper 1 –...
  • Page 19 Jumper 3 ~ Jumper 6 – Use these 3 x 4 pin jumpers to manually set the CPU clock ratio. Refer to the following table to set the CPU clock ratio for your processor by shorting the pins indicated. Short pins Fraction 3.0/8.5 3.5/9.0...

  • Page 20: Installing The Mainboard In A Case

    Refer to the following illustration and instructions for installing the mainboard in a case: 2. Secure the mainboard with This illustration shows screws where appropriate. an example of a main- board being installed in a tower-type case: Note: Do not over- tighten the screws as this can stress the...

  • Page 21: Connecting Case Components

    After you have installed the mainboard into a case, you can begin connecting the mainboard components. Refer to the fol- lowing: 1. Connect the case power supply connector to ATX1. 2. Connect the CPU cooling fan cable to CPUFAN1. 3. Connect the case cooling fan connector to PWRFAN1. The following page explains how to make panel connections.

  • Page 22: The Panel Connector

    The Panel Connector The panel connector provides a standard set of switch and LED connectors commonly found on ATX or Micro ATX cases. Refer to the table below for information: Device Pins Empty HDD LED Reset (Pin +1, -8) 13, 14 Switch PLEDY Power...

  • Page 23: Installing Hardware

    Installing the Processor Caution: When installing a CPU heatsink and cooling fan make sure that you DO NOT scratch the mainboard or any of the surface-mount resistors with the clip of the cooling fan. If the clip of the cooling fan scrapes across the main- board, you may cause serious damage to the mainboard or its components.
  • Page 24 CPU Installation Procedure The following illustration shows CPU installation components: Note: The Pin-1 corner is empty on both the socket and the CPU. Follow these instructions to install the CPU: 1. Pull the CPU socket locking lever away from the socket (A) to unhook it and raise the locking lever to the upright position (B).
  • Page 25 Note: The socket is designed to ZIF (Zero Insertion Force) specifications which means that the CPU pins should easily drop into the socket pin holes without any exertion or pressure on the CPU. 3. Swing the locking lever down and hook it under the latch on the edge of the socket.

  • Page 26: Installing Memory Modules

    7. Connect the CPU fan power cable to the CPUFAN1 connector. Note: The CPU fan/heatsink unit installation procedures may vary with the model of the fan/heatsink sup- plied. The form, size, and color of the fan/heatsink unit may also vary. Installing Memory Modules For this mainboard, you must use 168-pin 3.3V non-buffered Dual I n -line Memory Modules (DIMMs).
  • Page 27 The following table shows the maximum memory for DIMM based platforms: DRAM 1 DIMM 2 DIMMs Configuration (MB) (MB) (MB) (MB) 64 Mbit 8M x 8 64 Mbit 4M x 16 128 Mbit 16M x 8 128 Mbit 32M x 4 1024 Note: SS = Single Sided DS = Double Sided...
  • Page 28 DIMMs are keyed with cutouts so that they can only be installed correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. 3. Push the latches on each side of the DIMM slot down. Latch Cutouts Notches...

  • Page 29: Installing A Hard Disk Drive/Cd-Rom

    IDE channel. We recommend that you install IDE devices that support UDMA, and use IDE cables that support UDMA. Note: The P6VXM2T supports two VIA South Bridge chipsets —the VIA VT82C686A and the VIA VT82C686B. The VIA VT82C686A is standard and supports UDMA33/66.
  • Page 30 Installing a Hard Disk Drive 1. Install the hard disk drive into the drive cage in your system case. 2. Plug the IDE cable into IDE1 (A): Note: Ribbon cable connectors are usually keyed so that they can only be installed correctly on the device connector.
  • Page 31 Installing a CD-ROM/DVD Drive 1. Install the CD-ROM/DVD drive into the drive cage in your system case. 2. Plug the IDE cable into IDE1 (A). If you have already installed an HDD, use the other connector on the IDE cable. Note: Ribbon cable connectors are usually keyed so that they can only be installed correctly on the device connector.

  • Page 32: Installing A Floppy Diskette Drive

    5. Use the audio cable provided with the CD-ROM/DVD drive to connect to the mainboard CD-in connector CDIN1 or CDIN2 (D). When you first start up your system, the BIOS should auto- matically detect your CD-ROM/DVD drive. If it d oesn’t, enter the Setup Utility and configure the CD-ROM/DVD drive that you have installed.

  • Page 33: Installing Add-On Cards

    pin-1 side of each ribbon cable is always marked with a colored stripe on the cable. 3. Plug the correct connector on the FDD cable for the 5.25-inch or 3.5-inch drive into the FDD connector (B). 4. Plug a power cable from the case power supply into the power connector on the FDD.
  • Page 34 Note: Before installing an add-on card, check the docu- mentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation. 1. Remove a blanking plate from the system case corre- sponding to the slot you are going to use.

  • Page 35: Connecting Optional Devices

    Connecting Optional Devices Refer to the following for information on connecting the main- board’s optional devices: J1: Audio header This mainboard provides a second infrared, k eyboard, and mouse header, giving the option of installing second infrared, keyboard, and mouse ports on the front panel. Depending on your case and system configuration this connector may be more suitable as the sole IR port connector.
  • Page 36 Signal Name Signal Name Active LINE Out ( R ) Active LINE Out ( L ) GND (aLO) GND (aLO) GND (+12) GND (+12) +12V (1A) Cut away GND (MIC) Front LINE Out ( R ) LINE Next ( R ) Front LINE Out ( L ) LINE Next ( L ) GND (fLO)
  • Page 37 Signal Name Signal Name Cut away IRTX IRRX SJ1: Single color LED header This header allows the user to install an LED indicator to indi- cate when the computer is in Suspend to RAM (STR) mode or normal mode. Signal Name SUSLED-Y SUSLED-Y PWLED+...
  • Page 38 When your system is in a power-saving mode, any modem signal automatically resumes the system. You must enable this item using the Power Management page of the Setup Util- ity. See Chapter 3 for more information.

  • Page 39: Connecting I/O Devices

    The backplane of the mainboard has the following I/O ports: PS/2 Parallel port (LPT1) Game port mouse PS/2 Serial port Serial port Microphone keyboard ports COM 1 COM 2 Line-in Line-out PS/2 Mouse Use the upper PS/2 port to connect a PS/2 pointing device.

  • Page 40: External Connector Color Coding

    External Connector Color Coding Many connectors now use standard colors as shown in the table below. Connector Color Analog VGA Blue Audio line-in Light blue Audio line-out Lime Digital monitor/flat panel White IEEE 1394 Grey Microphone Pink MIDI/game Gold Parallel Burgundy PS/2-compatible keyboard Purple...

  • Page 41: Using Bios

    Using BIOS The computer uses the latest Award BIOS with support for Windows Plug and Play. The CMOS chip on the mainboard contains the ROM setup instructions for configuring the main- board BIOS. The BIOS (Basic Input and Output System) Setup Utility dis- plays the system's configuration status and provides you with options to set system parameters.

  • Page 42: The Standard Configuration

    The Standard Configuration A standard configuration has already been set in the Setup Utility. However, we recommend that you read this chapter in case you need to make any changes in the future. This Setup Utility should be used: • when changing the system configuration •...

  • Page 43: Entering The Setup Utility

    Entering the Setup Utility When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diag- nostics performed by the BIOS. After the POST routines are completed, the following message appears: Press DEL to enter SETUP Pressing the delete key accesses the Award BIOS Setup...

  • Page 44: Updating The Bios

    Updating the BIOS You can download and install updated BIOS for this main- board from the manufacturer's Web site. New BIOS provides support for new peripherals, improvements in performance, or fixes for known bugs. Install new BIOS as follows: 1. If your mainboard has a BIOS protection jumper, change the setting to allow BIOS flashing.

  • Page 45: Using Bios

    When you start the Setup Utility, the main menu appears. The main menu of the Setup Utility displays a list of the options that are available. A highlight indicates which option is cur- rently selected. Use the cursor arrow keys to move the highlight to other options.
  • Page 46 Date and Time The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility. IDE Devices (None) Your computer has two IDE channels (Primary and Secondary) and each channel can be installed with one or two devices...
  • Page 47 described below. Refer to your drive's documentation or look on the drive casing if you need to obtain this information. If no device is installed, change the value to None. Note: Before attempting to configure a hard disk drive, ensure that you have the configuration information supplied by the manufacturer of your hard drive.

  • Page 48: Advanced Bios Setup Option

    Advanced BIOS Setup Option This option displays advanced information about your system. CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software Advanced BIOS Features Anti-Virus Protection Disabled Item Help Y2K Monitor Disabled H/W Reset Function Enabled Menu Level CPU Internal Cache Enabled Allows you to choose...
  • Page 49 H/W Reset Function (Enabled) Enables or disables the computer’s hardware reset button. The default setting is Enabled. CPU Internal Cache CPU Internal Cache (Enabled) All the processors that can be installed in this mainboard use internal level 1 (L1) cache memory to improve performance. Leave this item at the default value Enabled for better per- formance.
  • Page 50 Boot Other Device (Enabled) If you enable this item, the system will search all other possible locations for an operating system if it fails to find one in the devices specified under the first, second and third boot devices. Swap Floppy Drive (Disabled) If you have two floppy diskette drives in your system, this item allows you to swap the assigned drive letters so that drive A becomes drive B, and drive B becomes drive A.
  • Page 51 Security Option (Setup) If you have installed password protection, this item defines if the password is required at system start up, or if it is only re- quired when a user tries to enter the Setup Utility. OS Select For DRAM > 64 MB (Non-OS2) This item is only required if you have installed more than 64 MB of memory and you are running the OS/2 operating sys- tem.

  • Page 52: Advanced Chipset Features Option

    Advanced Chipset Features Option These items define critical timing parameters of the main- board. You should leave the items on this page at their default values unless you are v ery familiar with the technical specifi- cations of your system hardware. If you change the values incorrectly, you may introduce fatal errors or recurring instabil- ity into your system.
  • Page 53 P2C/C2P Concurrency When disabled, the CPU bus is occupied during the entire PCI operation period. System BIOS Cacheable (Enabled)/ Video RAM Cacheable (Enabled) These items allow the video and/or system to be cached in memory for faster execution. We recommend that you leave these items at the default value.
  • Page 54 OnChip USB (Enabled) This should be enabled if your system has a USB installed on the system board and you wish to use it. USB Keyboard Support (Disabled) Enable this item if you plan to use a keyboard connected through the USB port in a legacy operating system (such as DOS) that does not support Plug and Play.
  • Page 55 AGP Master 1 WS Write (Disabled) This implements a single delay when writing to the AGP Bus. By default, two-wait states are used by the system, allowing for greater stability. AGP Master 1 WS Read (Disabled) This implements a single delay when reading to the AGP Bus. By default, two-wait states are used by the system, allowing for greater stability.

  • Page 56: Integrated Peripherals Option

    Integrated Peripherals Option These items define the operation of peripheral components on the system's input/output ports. CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software Integrated Peripherals OnChip IDE Channel0 Enabled Item Help OnChip IDE Channel1 Enabled IDE Prefetch Mode Enabled Menu Level Primary Master...
  • Page 57 vice. This mainboard supports UltraDMA. UltraDMA technol- ogy provides faster access to IDE devices. If you install a device that supports UltraDMA, change the ap- propriate item on this list to Auto. You may have to install the UltraDMA driver supplied with this mainboard in order to use an UltraDMA device.
  • Page 58 are Full and Half (default). Full-duplex means that you can transmit and send information simultaneously. Half-duplex is the transmission of data in both directions, but only one direction at a time. TX, RX inverting enable (No, Yes) Defines the voltage level for Infrared module RxD (receive) mode and TxD (transmit) mode.
  • Page 59 Sound Blaster (Disabled) Enables or disables Sound Blaster function. SB I/O Base Address (220H) This item lets you set the I/O base address for the Sound Blaster card. SB IRQ Select (IRQ 5) This item lets you set the Interrupt Request (IRQ) for the Sound Blaster card.

  • Page 60: Power Management Setup Option

    Power Management Setup Option This option lets you control system power management. The system has various power-saving modes including powering down the hard disk, turning off the video, suspending to RAM, and software power down that allows the system to be auto- matically resumed by certain events.
  • Page 61 ripherals on and off for improved power manage- ment. It also allows the PC to be turned on and off by external devices, so that mouse or keyboard ac- tivity wakes up the computer. Power Management This item enables you to choose the type of Power Manage- ment you want.
  • Page 62 Suspend Mode (Disable) The CPU clock will be stopped and the video signal will be suspended if no Power Management events occur for a speci- fied length of time. Full power function will return when a Power Management event is detected. Options are from 1 Min to 1 Hour and Disable.
  • Page 63 If the item is set to Instant-Off, then the power button causes a software power down. If the item is set to Delay 4 Sec. then you have to hold the power button down for four seconds to cause a software power down. AC Resume Function (Always Off) This sets the power state after a shutdown due to an unex- pected interrupt of AC power.
  • Page 64 saving timeout counters when any activity is detected on the hard disk drive or the floppy diskette drive. PCI Master (Off) When set to Off any PCI device with Master function will not power on the system. PowerOn by PCI Card (Enabled) Use this item to enable PCI activity to wakeup the system from a power saving mode.
  • Page 65 IRQs Activity Monitoring This item opens a submenu that enables you to set IRQs that will re- sume the system from a power saving mode. Select IRQs Activity Monitoring and press <Enter> to display the following menu: CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software IRQs Activity Monitoring IRQ 3 (COM2)

  • Page 66: Pnp/Pci Configuration Option

    PNP/PCI Configuration Option These options configure how PnP (Plug and Play) and PCI expansion cards operate in your system. Both the ISA and PCI buses on the Mainboard use system IRQs (Interrupt Re- Quests) and DMAs (Direct Memory Access). You must set up the IRQ and DMA assignments correctly through the PnP/PCI Configurations Setup utility for the mainboard to work properly.
  • Page 67 In the IRQ Resources sub-menu, if you change any of the IRQ as- signations to Legacy ISA, then that Interrupt Request Line is reserved for a legacy ISA expansion card. Press <Esc> to close the IRQ Resources sub-menu. In the Memory Resources sub menu, use the first item Re- served Memory Base to set the start address of the memory you want to reserve for the ISA expansion card.

  • Page 68: Pci Health Status Option

    PCI Health Status Option On mainboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds. CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software PC Health Status Shutdown Temperature Disabled Item Help Current CPU Temp.

  • Page 69: Frequency/Voltage Control

    Frequency/Voltage Control This item enables you to set the clock speed and system bus for your system. The clock speed and system bus are deter- mined by the kind of processor you have installed in your system. CMOS Setup Utility – Copyright (C) 1984 – 2000 Award Software Frequency Control Auto Detect DIMM/PCI Clk Enabled...

  • Page 70: Load Fail-Safe Defaults Option

    Load Fail-Safe Defaults Option This option opens a dialog box that lets you install fail-safe de- faults for all appropriate items in the Setup Utility: Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not install the defaults. The fail-safe de- faults place no great demands on the system and are generally stable.

  • Page 71: Set Supervisor And User Passwords Options

    Set Supervisor and User Passwords Options These items can be used to install a password. A Supervisor password takes precedence over a User password, and the Supervisor can limit the activities of a User. To install a pass- word, follow these steps: 1.

  • Page 72: Save & Exit Setup Option

    Save & Exit Setup Option Highlight this item and press <Enter> to save the changes that you have made in the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <Y> to save and exit, or press <N> to return to the main menu: Exit Without Saving Highlight this item and press <Enter>...

  • Page 73: Using The Mainboard Software

    Using the Mainboard Software The support software CD-ROM that is included in the main- board package contains all the drivers and utility programs needed to properly run the bundled products. Below you can find a brief description of each software program, and the lo- cation for your mainboard version.

  • Page 74: Auto-Installing Under Windows 98

    The Auto-install CD-ROM makes it easy for you to install the drivers and software for your mainboard. Note: If the Auto-install CD-ROM does not work on your system, you can still install drivers through the file manager for your OS (for example, Windows Ex- plorer).

  • Page 75: Running Setup

    Browse CD The Browse CD button is the standard Windows command that allows you to open Windows Explorer and show the con- tents of the support CD. Before installing the software from Windows Explorer, look for a file named README.TXT, INSTALL.TXT or something simi- lar.
  • Page 76 Note: The following screens are examples only. The screens and driver lists will be different according to the mainboard you are installing. The mainboard identification is located in the upper left-hand corner. 2. Click Next. The following screen appears: 3. Check the items you want to install. The default op- tions are recommended.

  • Page 77: Manual Installation

    Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory. This file contains the information needed to locate the drivers for your mainboard. Look for the chipset and mainboard model; then browse to the directory and path to begin installing the drivers.
  • Page 78 PC-CILLIN The PC-CILLIN software program provides anti-virus protec- tion for your system. This program is available for Windows 2000/ME/98SE and Windows NT. Be sure to check the r e - adme.txt and install the appropriate anti-virus software for your operating system. We strongly recommend users to install this free anti-virus software to help protect your system against viruses.
  • Page 79 dows application system that protects your Hard Disk Drive from virus intrusion, accidental deletions, and system corrup- tion. To install the Recovery Genius software program run SETUP.EXE from the following directory \UTILITY\RECOVERY GENIUS\ENG\RECOVERYGENIUS Language Genius The Language Genius is a software-based product that helps you to learn new languages.

  • Page 80: Setting Jumpers

    Setting Jumpers Jumper Settings Jumper Type Description Setting (default) 3-pin Clear CMOS 1-2: Normal 2-3: Clear CMOS JP3~JP6 12-pin CPU Clock Refer to next Ratio page 2-pin BIOS flash Short: Enable protection Open: Disable JP10 3-pin AC power 1-2: Enable JP10 resume 2-3: Disable...
  • Page 81 Jumper 3 ~ Jumper 6 – Use these 3 x 4 pin jumpers to manually set the CPU clock ratio. Refer to the following table to set the CPU clock ratio for your processor by shorting the pins indicated. Short pins Fraction 3.0/8.5 3.5/9.0...

  • Page 82: The Panel Connector

    The Panel Connector The panel connector provides a standard set of switch and LED connectors commonly found on ATX or Micro ATX cases. Refer to the table below for information: Device Pins Empty HDD LED Reset 13, 14 (Pin +1, -8) Switch PLEDY Power...

Table of Contents