Download Print this page

Husqvarna AME 1600 Operator's Manual

Hide thumbs

Advertisement

Quick Links

AME 1600
EN
Operator's manual
2-14

Advertisement

loading

  Summary of Contents for Husqvarna AME 1600

  • Page 1 AME 1600 Operator's manual 2-14...
  • Page 2: Table Of Contents

    Contents Introduction..............2 Troubleshooting............10 Safety................3 Storage and disposal............ 11 Operation................ 7 Technical data.............. 12 Maintenance..............8 EC Declaration of Conformity........14 Introduction Product description for concrete vibration. Do not use the product for other tasks. The product is a concrete vibrator with a built-in electrical drive unit.
  • Page 3: Safety

    1. Product type Read the manual carefully and make sure 2. Serial number that you understand the instructions before 3. Rated power you use the product. 4. Frequency, Hz 5. Motor speed, rpm 6. Product weight 7. IP classification Use approved protective gloves. 8.
  • Page 4 protected supply. Use of a RCD reduces the risk of CAUTION: Used if there is a risk of damage electric shock. to the product, other materials or the adjacent area if the instructions in the Personal safety manual are not obeyed. •...
  • Page 5 Power tools are dangerous in the hands of untrained • Do not use the product if you are tired, ill, or under users. the influence of alcohol, drugs or medicine. • Maintain power tools and accessories. Check for • Always be careful and use your common sense. misalignment or binding of moving parts, breakage •...
  • Page 6 electricity. Do not operate the product unless you • The fatal lung diseases chronic bronchitis, know that it is in a safe work area. silicosis and pulmonary fibrosis • Cancer Vibration safety • Birth defects • Skin inflammation • Use correct equipment to decrease the quantity of WARNING: Read the warning instructions dust and fumes in the air and to decrease dust on that follow before you use the product.
  • Page 7: Operation

    • Use boots with steel toe-cap and non-slip sole. • Do not do modifications to the product. Modifications that are not approved by the manufacturer can • Use approved work clothing or equivalent close- cause serious injury or death. fitting clothing that has long sleeves and long legs. •...
  • Page 8: Maintenance

    To start the product 3. Wait approximately 10–20 seconds until the surface around the vibrator head is shiny and no air bubbles 1. Make sure that the power switch is set to the OFF come to the surface. position. 2. Connect the product to an applicable power socket. 3.
  • Page 9 Before Each 2 Monthly, Maintenance use, weeks, each each 10h 100h 150h Make sure that the controls can move smoothly. Examine the commutator and the commutator membrane for damages. Lubricate the inner shaft of the flexible shaft. Examine the carbon brushes. Replace the carbon brushes if they are worn or damaged.
  • Page 10: Troubleshooting

    5. Install the air filter cover with the screws. 3. Remove the eccentric element (D) and the 2 bearings (E) from the tube. To disassemble and assemble the vibrator head 1. Remove the end cap (A) and the tube connector (B) from the tube.
  • Page 11: Storage And Disposal

    Problem Cause Solution The power switch There is overload in the vibrator head. Lift the vibrator head from the concrete and disengages. put it in again. The vibrator head is too hot because the air Remove blockage in the air intake or the air intake or air outlet is clogged.
  • Page 12: Technical Data

    Technical data Technical data UK/US-CAN Voltage, V Phases Frequency, Hz 50/60 50/60 Power, kW/hp 1.6/2.25 @12000 rpm 1.6/2.25 @12000 rpm Amperage, A Protection IP44 IP44 Insulation class Dimensions, L×W×H, mm/in. 371.7×140.8×204.6/ 371.7×140.8×204.6/ 14.6×5.54×8.05 14.6×5.54×8.05 Cable length, m/ft 5/16 5/16 Weighted effective acceleration uncertainty (K), m/s 4.16 or 0.71 4.16 or 0.71 ft/s...
  • Page 13 Flexible shaft Shaft length, m/ft. 1/3.25 1.50/5 2.00/6.5 3.00/10 4.00/13 Shaft weight, kg/lbs 2.40/5 3.00/6.625 3.80/8.375 5.60/12.375 7.30/16 Grease type KLUBER GBU Y131 grease or equivalent Grease quantity Approximately 15 grams per meter of the shaft Noise and vibration declaration statement These declared values were obtained by laboratory type testing in accordance with the stated directive or...
  • Page 14: Ec Declaration Of Conformity

    +46-36-146500, declare on our sole responsibility that the product: Description Concrete vibrator Brand Husqvarna Type/Model AME 1600 + AT 29, AT 39, AT 49, AT 59 Identification Serial numbers dating from 2019 and onwards complies fully with the following EU directives and regulations: Directive/Regulation Description 2006/42/EC "relating to machinery"...
  • Page 15 1154 - 001 - 05.03.2020...
  • Page 16 www.husqvarnacp.com Original instructions 1140470-26 2020-03-12...

This manual is also suitable for:

Vibrastar 40Vibrastar 50Vibrastar 60