Husqvarna TS 250 X3 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Power Tool
  5. TS 250 X3
  6. Operator's manual

Husqvarna TS 250 X3 Operator's Manual

Tile saw
Hide thumbs Also See for TS 250 X3:
Table of Contents

Advertisement

Quick Links

Operator's manual
TS 250 X3
It is the owner's responsibility to ensure that all operators of this machine have
read and understood the content of this manual before using the product!
Careless or improper use of this machine can cause serious or even fatal injury!
Allow only competent adults to operate this machine!
GB

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna TS 250 X3

Summary of Contents for Husqvarna TS 250 X3

  • Page 1 Operator’s manual TS 250 X3 It is the owner’s responsibility to ensure that all operators of this machine have read and understood the content of this manual before using the product! Careless or improper use of this machine can cause serious or even fatal injury!

  • Page 2: Table Of Contents

    EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED WITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR WITH THE SAFETY WARNINGS. FAILURE TO OBEY WARNINGS MAY RESULT IN INJURY OR DEATH. FOLLOW INSTRUC- TIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION.

  • Page 3: Symbol Definitions

    Symbol Definitions Symboles Definición De Los Simbolos • Please read the instructions for use prior to operating the machine for the first time. Avant toute mise en service, lire attentivement la notice et se familiariser avec la machine. • • Antes de la puesta en marcha, lea detenidamente las instrucciones y familiaricese con la máquina.
  • Page 4 • Motor Off Arrêt Du Moteur •. • Parar El Motor • Use In Well Ventilated Area A Utiliser Dans Un Endroit Bien Ventilé •. • Usar En Una Área Bien Ventilada • Do Not Use In Flammable Areas Ne Pas Utiliser Dans Des Ambiances Comportant Un Risque D’incendie •.

  • Page 5: Hearing Hazard Warning

    • Repairs Are To Be Done By An Authorized Dealer Only Les réparations ne peuvent être exécutées que par un distributeur agréé •. • Las Reparaciones Deben Ser Efectuadas Únicamente Por Un Distribuidor Autorizado • Diamond Blade Disque diamanté •. •...

  • Page 6: Dust Warning

    DUST WARNING Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which frequently contains silica. Silica is a basic component of sand, quartz, brick clay, granite and numerous other minerals and rocks. Exposure to excessive amount of such dust can cause: •...

  • Page 7: Decal Descriptions And Locations

    DECALS & LOCATIONS ETIQUETAS Y SU UBICACIÓN AUTOCOLLANTS ET LEURS EMPLACEMENTS 504 86 24-01 (x2) Location: Both Sides of Pan 504 04 02-01 (x2) Location: Front Top Corner of Blade Guard 542 19 07-36 Location: Rip Fence 542 19 07-39 Location: Front of Pan 542 19 37-94 Location: On Drain Plug End of...

  • Page 8: Safety First

    SAFETY FIRST! WARNINGS DO’s AND DO NOT’s WARNING: .FAILURE TO COMPLY WITH THESE WARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. read this entire operator’s manual before operating this machine. Understand all warnings, instructions, and controls. keep all guards in place and in good condition.

  • Page 9: Safety Warnings - Dos & Do Nots

    This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which is it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Husqvarna Construction Products and we have advised you. Husqvarna Construction Products...

  • Page 10: Figures: Figure 1

    FIGURE 1 Assembly Component Identification Major Assemblies in Shipping Carton Pan Guides Cutting Head Assembly: Includes Water Pan Stops Tube Assembly (L)} Drain Plug Frame Assembly Bearing Cap & Fasteners Water Pan Assembly TIle Saw Wrench (15/16” x 9/16” x 1/2”) Conveyor Cart Assembly (4) with Rip Fence Locking Knob (S) included. Lockbar Water Pump and Accessory Carton: In- Water Pump cludes Water Pump (H), Hose Barb (J), Hose Barb Fitting Water Valve (K), 15/16”-9/16”-1/2” Wrench Water Valve (E), Drain Plug (C), Locking Knob (F) with...

  • Page 11: Features

    The Water Pan (2) is removable for easy (For information or availability of other accessories con- cleaning. tact your Husqvarna supplier.) • The free-rolling Conveyor Cart (4) is aligned for straight, smooth cuts. The Back stop with ruler allows Blade Capacity: Rim Ø...
  • Page 12 For the best results, always use genuine Husqvarna® diamond blades. Contact Water Pump Assembly (5) Set-up: your nearest dealer to select the correct blade for your Remove the Water Pump (H), Hose Barb (J), the specific cutting needs.

  • Page 13: Operating Procedure

    Raise the Blade Guard (M) to fully up and tighten OPERATING PROCEDURE the wing nut on the side to hold it in the raised position. WARNING: Read the Operating Procedure Remove the Arbor Nut (O) and the Outer Blade Flange (P). Use Blade Shaft Lock if needed. See completely before operating your tile saw.

  • Page 14: Figure 3

    DEPTH LINKING PROTECTION Your tile saw is factory assembled and aligned prior to shipment to ensure accurate cuts when your saw is delivered. However, since Husqvarna® cannot control rough handling during shipping, it is suggested that the FIGURE 3 alignment be checked. If the saw is found in need of adjustment, refer to the appropriate section(s) below.

  • Page 15: Profile Wheel Set-Up And Use

    Simple daily maintenance and care will add to the life and productivity of your saw. After each day’s use: CLEAN The tilesaw is designed for use with a Husqvarna® 6” Profile Wheel, such as 542 62 10-81* (3/8” Radius) or THE MACHINE!! 542 62 10-82* (1/2”...

  • Page 16: Figure 4

    Contact your authorized 2. Disconnect Electrical Plug from Outlet, then 3. Remove the Pump, then Husqvarna® dealer concerning maintenance and re- 4. Back Flush. V-Belt Tensioning with Cam Adjustment: Back flushing is done by forcing water into the pump Always set the Motor Switch to OFF and un- discharge and out through the screen.

  • Page 17: Tile Cutting Accessories

    FOLDING STAND: 542 20 32-52* - This stable stand ADJUSTABLE PROTRACTOR: 542 05 10-10* - The brings a Husqvarna® tile saw to standing level for Protractor can be used to rip cut known angles. The ease of work. The stand conveniently folds flat for protractor clamps to the backstop.

  • Page 18: Wiring Diagrams

    Diagram 1: Wiring Diagram 542 20 30-79, 1.5HP, 115V/60/1...

  • Page 19: Wiring Diagrams

    Diagram 2: Wiring Diagram 542 00 06-05, 1.5 HP, 115V/208-230/60/1...
  • Page 20 NOTES: NOTAS: REMARQUE :...

  • Page 21: Warranty

    Customer Service: 913-928-1300 Customer Serv. Fax: 913-438-7938 www.husqvarna.com Please record the Date of Purchase and the Serial Number, the Model Number of the equipment and the Date of Purchase of your equipment in the space below. When ordering service items, please have this information available.
  • Page 22 www.husqvarnacp.com 503 39 43-01 2014-09-24 Printed In U.S.A.

Table of Contents