Download Print this page

Husqvarna LX 90 Operator's Manual

Hide thumbs

Advertisement

LX 90
EN
Operator's manual
2-16

Advertisement

loading

  Summary of Contents for Husqvarna LX 90

  • Page 1 LX 90 Operator's manual 2-16...
  • Page 2: Table Of Contents

    Contents Introduction..............2 Transportation, storage and disposal......12 Safety................4 Technical data.............. 14 Operation................ 8 EC Declaration of Conformity........16 Maintenance..............10 Introduction California Proposition 65 WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm.
  • Page 3 Product overview Symbols on the product 1. Throttle control 2. Safety frame and handle WARNING: This product can be dangerous 3. V-belt cover and cause serious injury or death to the 4. Vibration damping units operator or others. Be careful and use the 5.
  • Page 4: Safety

    Type plate Hot surface. Keep your hands away from this area. XXXXXXXXXX Risk of crush injuries. 1. Product type 2. Product number 3. Product weight 4. Serial number 5. Manufacturer 6. Rated power 7. Production year Lifting point on the safety frame. Product liability Noise emission to the environment as referred to in the EC directive.
  • Page 5 • Always be careful and use your common sense. the product hits a hidden object, stop the engine immediately and examine the product and the object. • This product produces an electromagnetic field Do not start to operate the product again until you during operation.
  • Page 6 • Do a check of the safety devices regularly. If the safety devices are defective, speak to your Noise safety Husqvarna service agent. Engine ON/OFF switch WARNING: Read the warning instructions that follow before you use the product. The engine can only start when the engine ON/OFF switch is set to "ON".
  • Page 7 To do a check of the engine ON/OFF switch • Fuel is flammable and the fumes are explosive. Be careful with fuel to prevent injury, fire and explosion. To start the product on 1. Start the engine. Refer to • Do not breathe in the fuel fumes.
  • Page 8: Operation

    • Do not park the product on a slope. If you must park • Stop the engine and make sure that all parts of the the product on a slope, make sure that the product product are cool before you do the maintenance. cannot fall.
  • Page 9 To stop the product 4. Set the engine ON/OFF switch to "ON". 1. Move the throttle control to the idle speed position. 2. Set the ON/OFF switch to "OFF". The engine stops. 3. Move the fuel valve to the "OFF" position. To do if the engine does not start If the engine does not start and white smoke shows, do the procedure that follows.
  • Page 10: Maintenance

    Maintenance Introduction Maintenance schedule * = General maintenance done by the operator. The WARNING: Read and understand the safety instructions are not given in this operator's manual. chapter before you do maintenance on the X = The instructions are given in this operator's manual. product.
  • Page 11 Engine maintenance Before use, After the Weekly, Yearly, each each 10 h first 20 h each 100 h 300 h Replace the fuel filter. To clean the product 2. Remove the oil drain plug (A) and connect a hose (B). •...
  • Page 12: Transportation, Storage And Disposal

    2. Remove the paper filter element and the foam filter 10. Push a clean cloth against the foam filter element to element (A). remove unwanted oil. 11. Install the air filter in the opposite sequence. To do a check of the V-belt WARNING: Do not operate the product without the V-belt cover installed.
  • Page 13 (A) and the vibration damping units (B) • When the product is no longer in use, send it to a are correctly installed and not damaged. Husqvarna dealer or discard it at a recycling location. To safety the product to a transportation vehicle with tie-down straps •...
  • Page 14: Technical Data

    Technical data Technical data Net weight, kg/lb 95/209 Operation weight (EN500, incl. oil, ½ fuel), kg/lb 96.4/212.5 Engine brand, type Honda, GX 160 Engine power, kW/hp @rpm 3.5/4.7 @3300 Vibration frequency, Hz/rpm 75/4500 Amplitude, mm/in. 1.7/0.06 Centrifugal force, kN/lbf 16/3596 Operation speed, m/min or ft./min 22 or 82 Max.
  • Page 15 Noise and vibration declaration statement These declared values were obtained by laboratory type testing in accordance with the stated directive or standards and are suitable for comparison with the declared values of other products tested in accordance with the same directive or standards. These declared values are not suitable for use in risk assessments and values measured in individual work places may be higher.
  • Page 16: Ec Declaration Of Conformity

    EC Declaration of Conformity EC Declaration of Conformity We, Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare on our sole responsibility that the product: Description Forward Plate Compaction Machine Brand Husqvarna Type/Model LX 90 Identification Serial numbers dating from 2020 and onwards...
  • Page 17 1096 - 003 - 06.04.2020...
  • Page 18 1096 - 003 - 06.04.2020...
  • Page 19 1096 - 003 - 06.04.2020...
  • Page 20 www.husqvarnacp.com Original instructions 1140394-26 2020-04-06...