Page 1
I N S TA L L AT I O N MA N UA L Kraus Stainless Steel Undermount Kitchen Sink KBU10 / KBU11 / KBU12 / KBU14 / KBU15/ KBU16 / KBU17 / KBU21 / KBU22 / KBU23 / KBU24 / KBU25 / KBU26 / KBU27 / KBU28 / KBU29...
Page 2
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help.
Toll-Free: 800-775-0703 or Customerservice@kraususa.com The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a licensed professional.
Page 8
Step1 2. Position Template • Check the cut-out template against the actual sink to ensure a proper sized cut-out • Place the cut-out template in the desired location on the countertop NOTE: Make sure clearance is suitable for backsplash, faucet, and plumbing for the sink Step6...
Page 9
Step2 3. Trace Template • Trace template on countertop with a pencil...
Page 10
Step3 4. Cut Countertop • Cut the opening in the countertop by carefully following the traced line Step3 Please use the appropriate saw that best fits your countertop NOTE: material...
Page 11
Determine location for mounting brackets; space 5. Set up Mounting Brackets 3/8”POSITIVE 1/8”NEGATIVE • Turn countertop over and align sink with countertop. Decide location for mounting brackets ZERO Centerline • Mounting holes should be ½” from edge of sink Step5 Step6 1/2"...
Page 12
Step6 7. Install Anchors • Insert anchors into drilled holes and lightly tap with a hammer until flush Step7 8. Secure Sink to Countertop • Use a bead of silicone (or preferred adhesive) around the rim of the sink. Check the alignment of the sink to the cutout in the countertop. Place sink over cutout hole and press firmly...
9. Attach Mounting Hardware Step8 • Attach mounting hardware to secure bowl. Remove excess sealant from inside lip • Allow sealant to set for 30 – 60 minutes Use acetone or rubbing alcohol to remove any excess sealant NOTE:...
Page 14
10. Install Plumbing Fixtures • Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer’s instructions Step9 • Run water into sink and check for leaks...
Page 15
Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com If you are a HOMEOWNER please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive...
Page 16
Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.com Like & Follow KrausUSA Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance www.kraususa.com www.kraususa.com...
Page 17
3. Place the faucet on the countertop. 4. If the countertop is thin or the faucet is being mounted on the sink itself, place the countertop extender (#11) from underneath the countertop and tighten it onto the tailpiece (#5). **OPTIONAL** 5.
Page 18
Rubber Washe Tailpiece Metal Washer Fixing set Weight Hot & Cold Water Lines Pullout hose (ALREADY ATTACHED) Faucet Extender (optional) IMPORTANT Screw at back of faucet tightens the goose neck to the body. Connecting pullout hose to copper tube Copper Tube...
Page 21
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help.
Toll-Free: 800.775.0703 or Customerservice@kraususa.com The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a licensed professional.
GDA-1 Diagram and Parts List: a. Pump b. Dispenser Base c. Rubber Washer A d. Rubber Washer B e. Mounting Nut f. Dispenser Bottle TOOLS REQUIRED: *Adjustable Wrench...
Page 25
Step 2 Install dispenser base (b) with rubber washer A (c) attached into the hole in the countertop. Re-install rubber washer B (d) and mounting nut (e) on the dispenser base (b) from underneath the countertop. Tighten mounting nut (e) with adjustable wrench until snug...
Page 26
Step 3 Screw the dispenser bottle (f ) to the dispenser base (b) from underneath the countertop. Tighten as required. Fill the dispenser bottle (f ) from the top with 12 ounces of soap...
Page 27
Step 4 Insert pump (a) into dispenser base (b) from the top. Press the pump several times to make sure soap is evenly distributed Press...
Page 28
Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a PLUMBING CONTRACTOR OR TRADE PROFESSIONAL please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com...
Page 31
Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.com Like & Follow KrausUSA Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance www.kraususa.com...