Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kraus Arlo KBF-1200
Summary of Contents for Kraus Arlo KBF-1200
- Page 1 INSTALLATION MANUAL Arlo™ Single Handle Vessel Faucet KBF-1200...
- Page 2 Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: DO NOT RETURN TO STORE...
-
Page 3: Prior To Installation
Make sure you have all necessary parts by checking the diagram and · parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. Read all instructions and safety warnings and ensure you have all tools, ·... - Page 4 Diagram and Parts List F. Flange & Washer A. Faucet Body G. Aerator B. Plastic Washer C. Metal Washer H. Aerator Key D. Nut & Screws I. Hex Wrench E. Waterlines J. Drain...
-
Page 5: Faucet Dimensions
Faucet Dimensions 6 3/4" [171mm] 5" [128mm] 12 1/8" [307mm] 8 1/8" [208mm] 2 1/4" [56mm] 2 1/2" [64mm] 3/8" compression Installer Tip: Shut off main water supply before installing new faucet. -
Page 6: Step 2: Installing The Faucet
Step 1: Remove washers and nut Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove the plastic washer (B), metal washer (C) and nut & screws (D) from the faucet (A). Step 2: Installing the faucet Before installation, ensure that the flange (F) is placed on the bottom of the faucet assembly (A). - Page 7 Step 3: Connect waterlines to main valve Attach waterlines (E) to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON). Step 4: Install Press pop-up assembly Unscrew the nut (6) from the pop-up body (2), move over the tail pipe (7) and washer (5), then unscrew the coupling nut (4) and remove the...
- Page 8 Step 4: Install Press pop-up assembly - continued Place the washer (1) underneath the flange of the pop-up body (2). Slide the pop-up body (2) down through the drain hole on the vessel or basin sink. From the underside of the sink, slide the washer (3) against the bottom of the vessel or basin sink, thread on the coupling nut (4) and tighten.
-
Page 9: Replacement Parts
Replacement Parts Replacement Parts List Finish / Color Part # 1. Cover Button GR, BL* KP27002 2. Set Screw KP27001 CH, SFS, ORB, MB 3. Handle KP27046 CH, SFS, ORB, MB 4. Cap KP27048 7 5/8” 5. Bonnet Nut KP27049 6. -
Page 10: Troubleshooting
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Bonnet nut (5) has Remove the index (1). Loosen set screw Leakage under the handle. come loose. (2) with hex wrench (15). - Page 11 Kraus warrants the structure and finish of the Faucet to be free from defects in material and workmanship under normal usage for as long as the original purchaser resides in the residence in which the Faucet was first installed.
- Page 12 TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND KRAUS USA PLUMBING, LLC SHALL NOT BE LIABLE FOR, ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE.
- Page 13 IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.com...