Dräger EPAS Operating Manual page 11

Important: If the two Evidential Breath Tests are not within 0.02
g/210L of each other, the Alcotest
two minute countdown.
After the countdown is completed,
indicating that a third test is required.
Once the test is completed, the Alcotest
in its memory.
If 2 out of 3 breath test results are not within 0.02 g/210L of each
other, "Invalid Test" will be printed on the printout.
The test results must be printed within five minutes or the Alcotest
7410 will time out and turn itself off. To print the test results after
Plus
the Alcotest 7410 has turned itself off, put the Alcotest
® Plus
the "PRN" mode (see page 11, "Re-printing the Last Test) and print
the results.
Printing Test Results
Test results from the Alcotest 7410
®
via the LEDs (ON and READY/ERROR lights) on the face of the
Alcotest 7410 .
® Plus
Note: If the breath test result is flashing, printing is not possible
because another breath sample must be provided. A non-
flashing result indicates successful 0.02 g/210L agreement
between two breath samples and completion of the test.
Follow the steps below to print test results.
1.) Place the Alcotest 7410
® Plus
facing the printer, so that the two lights (READY and ON) inter-
face with the printer window. (To ensure proper transmission,
keep window clean and free from scratches.)
2.) After a few seconds, the printer will begin to print the report.
Note: The date and time stamp indicated on the printout will
be the actual time of the breath test.
3.) Remove the Alcotest 7410
®
turn off the Alcotest 7410
®
fied. Once the printing has stopped, additional printouts can be
printed, as long as the results are displayed on the 7410 by align-
ing the Alcotest 7410 to the printer as outlined above.
® Plus
7410 will initiate another
® Plus
will be displayed
7410 will store the data
® Plus
7410
® Plus
can be transferred and printed
Plus
onto the printer with its front side
from the printer. Do not reset or
Plus
until the results have been veri-
Plus
18
Follow the steps below to turn the Alcotest
successful test:
1.) Press the power button on the Alcotest
the instrument displays "dAt".
2.) Double-click the power button twice to turn the Alcotest
Aborting a Test
If the subject does not deliver a breath sample within a pre-set time
frame (approx. 45 seconds, after
displayed),
®
will be displayed along with a series of short beeps.
in
The operator can abort the test while the Alcotest
beeping and
button while the beeping continues.
on the Alcotest
out will read "Test Aborted" and also display any results prior to
aborting the test.
If the ON/OFF button is not pressed , the instrument will cycle back
to
can be taken.
Note: The Alcotest
above "time out" sequence until a breath test is conducted
or
Test results from the Alcotest
via the LEDs on the face of the Alcotest
Note: If the breath test result is flashing, printing is not possible
because another breath sample must be provided.
A non-flashing result indicates successful 0.02 g/210L
agreement between two breath samples and completion
of the test.
The operator may now proceed to print the Test Results.
®
,
(allowing the operator to choose to end the test)
is on the display by pressing the ON/OFF
7410 , the test will be stored, and the print-
® Plus
, or , indicating that a breath sample
7410 will continue to go through the
® Plus
is selected.
7410 can be transferred and printed
® Plus
7410
®
19
7410 off after a
® Plus
7410 and wait until
Plus
7410 off.
® Plus
, or is
7410 is
® Plus
will be displayed
.
Plus