Advertisement
SPX SPARTAN
Floodlight Range–
CML13ATEX3007 & IEC Ex CML14.0001
This installation guide provides instructions for installing the Infra-Red and White-
Light SPARTAN series of explosion protected floodlights.
*Text in red is specific for emergency variants
Overview
IMPORTANT INFORMATION
The SPARTAN series of explosion protected bulkheads are specialist devices, certified
for use in specific operating environments.
The units must be installed in accordance with these instructions, must be correctly
certified for the specific operating environment and must be installed by suitably qualified
personnel.
*Emergency bulkheads will require the fuse to be reconnected upon installation and the
floodlight subjected to three 24 hour charge/discharge cycles to bring the battery up to
peak capacity.
If you have any queries about the installation or the certification of the unit – please
contact Raytec for immediate assistance and advice.
940-M-0003
Installation Guide
2. Installation
5. Trouble Shooting
Page 1
Revision B
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Raytec SPX SPARTAN SPX-BL24-W-1010
Summary of Contents for Raytec SPX SPARTAN SPX-BL24-W-1010
- Page 1 24 hour charge/discharge cycles to bring the battery up to peak capacity. If you have any queries about the installation or the certification of the unit – please contact Raytec for immediate assistance and advice. 940-M-0003 Page 1...
- Page 2 ‘T’ rating are suitable for the environment the unit is being installed in. 3. If the SPARTAN unit is to be installed in areas of high vibration, please consult with Raytec. 4. The SPARTAN unit housing is constructed from marine grade aluminium and toughened glass.
- Page 3 2. INSTALLATION Mounting SPARTAN Unit 1. To meet the requirements of certification a MINIMUM of 2 fixing points must be used, the fixing points must be suitable for the conditions of use. 940-M-0003 Page 3 Revision B...
- Page 4 SPARTAN BULKHEAD 24 FLOODLIGHT STANDARD/EMERGENCY VARIANT 2. The unit may have been supplied with an integrated photocell. Care should be taken when positioning the unit to ensure the sensor is not shielded, is not pointing directly at another light source and is monitoring the general, prevailing light conditions. 3.
- Page 5 Wire the Mains cable into the terminal block. Provision has been made for this and identified as the E (Earth), L (Live), Ls (Live switched) and N (Neutral) terminals. There are two pairs of contacts for each of these to facilitate a mains cable that can be looped in and out of the unit.
- Page 6 5. The unit has one independent power supply, in the event that the power supply needs to be replaced the cables to the LED and mains terminal block will need to be disconnected, the four M6 bolts released, then the power supply can then be removed. Fitting a new power supply is a reversal of the above procedure.
- Page 7 SPARTAN: White light Part Code Description SPX-BL24-W-1010 Spartan Bulkhead, 24 LED, White-Light, 10° option Spartan Bulkhead, 24 LED, White-Light, 30° option SPX-BL24-W-3030 SPX-BL24-W-5050 Spartan Bulkhead, 24 LED, White-Light, 50° option SPX-BL24-W-120120 Spartan Bulkhead, 24 LED, White-Light, 120°option SPX-BL24-W-3510 Spartan Bulkhead, 24 LED, White-Light, 35x10° SPX-BL24-W-6025 Spartan Bulkhead, 24 LED, White-Light, 60x25°...
- Page 8 DECLARATION OF CONFORMITY WITH THE ATEX DIRECTIVE 94/9/EC Raytec Ltd. declares under our sole responsibility that the product(s) listed below conform with the relevant provisions of directive 94/9/EC of 23 March 1994 Manufacturer Raytec Ltd Unit 3, Wansbeck Business Park...
Need help?
Do you have a question about the SPX SPARTAN SPX-BL24-W-1010 and is the answer not in the manual?
Questions and answers