1. Manuals
  2. Brands
  3. ASROCK Manuals
  4. Motherboard
  5. 1U2FH-4L
  6. User manual

ASROCK 1U2FH-4L User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual

Advertisement

Table of Contents
loading

Related Manuals for ASROCK 1U2FH-4L

Summary of Contents for ASROCK 1U2FH-4L

  • Page 2 Version 1.0 Published November 2015 Copyright©2015 ASRockRack Inc. All rights reserved. Copyright Notice: No part of this documentation may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRockRack Inc.
  • Page 3 Setting up the Server in a Restricted Access Location • Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken. • Access is through the use of a tool or lock and key, or other means of security, and is controlled by the authority responsible for the location.
  • Page 4 Contact Information If you need to contact ASRockRack or want to know more about ASRockRack, you’re welcome to visit ASRockRack’s website at www.ASRockRack.com; or you may contact your dealer for further information. ASRockRack Incorporation 6F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan (R.O.C.)

  • Page 5: Table Of Contents

    Contents Chapter 1 Introduction Shipping Box Contents Specifications Chapter 2 Server System Overview System Components Internal Features System Front Panel System Rear Panel Front Control Panel Buttons and LEDs PSU LED 3.5-inch Hard Drive Tray LEDs Chapter 3 Hardware Installation and Maintenance Server Top Cover Hard Drive Power Supply...
  • Page 6 Chapter 4 Backplane Specifications 4.1 Hard Drive Backplanes (BPB) 4.2 Front Panel Board (FPB) 4.3 Power Distribution Board (PDB) 4.4 Pin Definitions...

  • Page 7: Chapter 1 Introduction

    1U2FH-4L Chapter 1 Introduction Thank you for purchasing 1U2FH-4L, a reliable barebone system produced under ASRockRack’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRockRack’s commitment to quality and endurance. 1. Because the hardware specifications might be updated, the content of this documentation will be subject to change without notice.

  • Page 8: Shipping Box Contents

    1.1 Shipping Box Contents Item Quantity 1U2FH-4L Barebone (1U form factor) System Boards (MB) Power Supply Units System Fans HDD Backplane (BPB) Front Panel Board (FPB) Power Distribution Boards (PDB) Power Cable, ATX 8Pin, PDB to MB, 200mm Power Cable, ATX 8Pin, PDB to MB, 700mm...

  • Page 9: Specifications

    1U2FH-4L 1.2 Specifications 1U2FH-4L System Form Factor 1U Rackmount Chassis Model 1U2FH-4L Dimensions 28" x 16.9" x 17" (710 mm X 430 mm X 43.5 mm) Support MB EEB, 12''x13'' Front Panel Buttons • Power Button • UID Button LEDs •...

  • Page 10: Chapter 2 Server System Overview

    Chapter 2 Server System Overview This chapter provides diagrams showing the location of important components of the server system. 2.1 System Components Top Covers Riser Card Assembly 2 x Power Supply Units Server Board 5 x System Fans 2 x 2.5” HDD Carriers Front Controls and Indicators 4 x 3.5”...

  • Page 11: Internal Features

    1U2FH-4L 2.2 Internal Features...
  • Page 12 Item Server Board (SB) Riser Card Assembly PCIE Add-in Card 1 (on the riser card assembly)* or Storage Mezzanine Card (on the server board) PCIE Add-in Card 2 (on the riser card assembly)* or LAN Mezzanine Card (on the server board)** Power Supply Unit (PSU2) Power Supply Unit (PSU1) System Fan (FAN1)

  • Page 13: System Front Panel

    1U2FH-4L 2.3 System Front Panel HDD0 HDD1 HDD2 HDD3 Description 4 x 3.5" Hot-Swap HDD Trays (HDD0~HDD3) 2 x USB 2.0 Ports Control Panel Buttons and LEDs VGA Port 2.4 System Rear Panel Redundant PSU 1+1: Only one PSU is allowed to be removed while the server is running.

  • Page 14: Front Control Panel Buttons And Leds

    2.5 Front Control Panel Buttons and LEDs Front Control Panel USB1 USB2 Description USB 2.0 Port (USB1) USB 2.0 Port (USB2) Power Button and LED UID Button and LED* System Health LED* HDD Activity LED* LAN1, LAN2 Activity LED* *Please be noted that the functions are supported depending on the type of the motherboard. UID Button Press the UID button to toggle the front panel UID LED and the baseboard UID LED on and off.

  • Page 15: Psu Led

    1U2FH-4L System Health LED Status Description Solid Red There is a fault in the system. System is normally operating. HDD Activity LED Status Description Blinking Green At lease one of the HDDs is accessing data. Solid Green At lease one of the HDDs is connected.

  • Page 16: Inch Hard Drive Tray Leds

    2.7 3.5-inch Hard Drive Tray LEDs Description HDD Power LED HDD Activity LED Status LED Definitions HDD Power LED Status Description Blue HDD powered-on No power to HDD HDD Activity LED Status Description Solid Green HDD active Blinking Green HDD accessing or reading HDD failed HDD powered-off...

  • Page 17: Chapter 3 Hardware Installation And Maintenance

    1U2FH-4L Chapter 3 Hardware Installation and Maintenance This chapter helps you assemble the chassis and install components. Before You Begin Before you work with the server, pay close attention to the “Important Safety Instructions” at the beginning of this manual.

  • Page 18: Server Top Cover

    3.1 Server Top Cover Removing the Server Top Covers 1. Before removing the top cover, power off the server and unplug the power cord. 2. The system must be operated with the chassis top cover installed to ensure proper cooling. 1.
  • Page 19 1U2FH-4L 3. When the top rear cover has been removed, you can also remove the top front cover by pushing the top front cover toward the rear side.
  • Page 20 Installing the Server Top Cover 1. Lower the top front cover on the chassis, making sure the side latches align with the cutouts. Slide the top front cover toward the front. 2. Lower the top rear cover on the chassis, making sure the side latches align with the cutouts.

  • Page 21: Hard Drive

    1U2FH-4L 3.2 Hard Drive 3.2.1 Installing a Hard Disk Drive into 3.5" Hard Drive Tray The system supports hot-swappable 3.5" hard drives. Removing 3.5” Hard Drive Trays from the Chassis 1. Press the locking lever latch on the drive tray to unlock the retention lever.
  • Page 22 Installing a 3.5” Hard Drive to the Hard Drive Tray 1. Place a 3.5" HDD into the tray with the printed circuit board side facing down. Carefully align the mounting holes in the hard drive and the tray. 2. Secure the hard drive using four screws. 3.
  • Page 23 1U2FH-4L 3.2.2 Installing a Hard Disk Drive into 2.5" Hard Drive Carrier The system supports 2.5" hard drives (7mm). Removing 2.5” Hard Drive Carriers from the Chassis 1. Remove the screws that secures the hard drive carrier.
  • Page 24 Installing a 2.5” Hard Drive to the Hard Drive Carrier 1. Place the 2.5" HDD (7mm) into the carrier with the label facing up and the connector end toward the rear of the carrier where the mounting hole is located. Carefully align the mounting holes in the hard drive and the carrier.

  • Page 25: Power Supply

    1U2FH-4L 3.3 Power Supply The system can accommodate two AC or two DC power supplies in the bay at the rear of the chassis. Each unit provides up to 650 Watts of power. Only a single power supply is required for operation, with the second power supply purely as a redundant, load-sharing backup.
  • Page 26 Removing the Power Supply Unit To remove a failed power supply, please first identify the failed power supply . 1. Hold onto the power supply handle while pressing the locking lever towards the power supply handle. 2. Pull to remove the power supply from the chassis. 1.

  • Page 27: Add-In Card

    1U2FH-4L 3.4 Add-In Card 1. You can install up to two PCIE add-in cards to the chassis when they are installed on the provided riser card assembly. 2. Please be noted that you can install either a PCIE add-in card or a mezzanine card at one time only.
  • Page 28 3. Remove the screw securing the filler plate. 4. Push to release the the filler plate from the assembly. 5. Slide the filler plate out sideways. 6. Install an add-in card into the retainer plate and into the connector on the riser card assembly.
  • Page 29 1U2FH-4L 8. Place the assembly back into the chassis and secure it with screws.
  • Page 30 3.7 LAN Mezzanine Card Removing the Blanking Plate for a LAN Mezzanine Card If you need to remove the blanking plate, please remove the screws that secure the blanking plate on the chassis. Keep the screws for later use. *The pre-installed blanking plate is also the RJ-45 plug release module. Blanking Plate...
  • Page 31 1U2FH-4L Installing a LAN Mezzanine Card You can use an optional Ethernet mezzanine card for additional LAN ports. Please be aware that the mezzanine card must be used in conjunction with a matching I/O module. For M540R mezzanine card, you need to install the RJ-45 plug release module instead of a regular I/O module.
  • Page 32 4. Tighten the screws to secure the matching I/O module to the chassis. Install the RJ-45 plug release module instead for the M540 mezzanine card. RJ-45 Plug Release Module 5. If you use the RJ-45 plug release module, simply press it to release plugs.

  • Page 33: System Fan

    1U2FH-4L 3.5 System Fan Replacing the System Fan 1. Unplug the fan connecter and remove the failed fan. 2. Align the mounting holes on the fan bar with the fan mounts on the replacement fan. 3. Gently place the fan on the fan bar. Make sure the fan is well seated.

  • Page 34: Backplane

    3.6 Backplane The backplanes serve as the interfaces between the server board and the HDDs. Before removing and installing the backplanes, power off the server and unplug the power cord and make sure all 3.5” HDDs have been removed. For the specification of the backplane, please refer to the Chapter 4. Removing the Backplane 1.

  • Page 35: Server Board

    1U2FH-4L 3.7 Server Board Follow the steps below to install the server board to the chassis. 1. Hold the server board only by the edges. 2. Gently place the server board into the chassis. Sit the server board on the server board tray.

  • Page 36: Chassis Cables

    3.8 Chassis Cables This section lists supported cables for your chassis system. Cable type and quantity vary depending on the server board that comes with your system. BPB Cable, MiniSAS HD to 8087(L/A) (650mm) (Quantity: 1) Backplane Server Board SMBus Cable, 1*5Pin, PDB to MB (650mm) (Quantity: 1) Backplane Server Board Front Panel Cable (840+800mm) (Quantity: 1)*...
  • Page 37 1U2FH-4L VGA Cable (850mm) (Quantity: 1) Front Panel Server Board Power Cable, ATX 8Pin (200mm) (Quantity: 1) Server Board Power Cable, ATX 8Pin (700mm) (Quantity: 1) Server Board Power Cable, ATX 24Pin (450mm) (Quantity: 1) Server Board PMBus Cable (500mm) (Quantity: 1)
  • Page 38 Power Cable, ATX 12Pin to 3*4Pin, (250/300/350mm) (Quantity: 1) 2.5" HDD Cable, SATA 7+15 to 7Pin+1*4Pin (800&120mm) (Quantity: 2) Server Board 2.5”HDD Connections and cable routing may differ depending on various server boards. Please refer to the Quick Installation Guide to know the exact headers or connectors to be connected on the server board you purchase.
  • Page 39 1U2FH-4L Chapter 4 Backplane Specifications 4.1 Hard Drive Backplanes (BPB) Top View HBA0 PWR_HDD1 PWR_HDD2 BMC_SMB1 Description HDD Power Connector (PWR_HDD1) HDD Power Connector (PWR_HDD2) Mini-SAS HD Connector (HBA0) BMC SMBus Connector (BMC_SMB1)
  • Page 40 4.2 Front Panel Board (FPB) Top View AUX_PANEL1 USB_HEADER1 Description LAN 2 Activity LED (LAN2_LED1) LAN 1 Activity LED (LAN1_LED1) HDD LED (HDD_LED1) System Health LED (SYS_LED1) UID Button and LED (UID_BTN1) Power Button and LED (PWR_BTN1) Front USB 2.0 Connector (USB_2) Front USB 2.0 Connector (USB_1) USB Header (USB_HEADER1) Front and Auxiliary Panel Header (AUX_PANEL1)
  • Page 41 1U2FH-4L 4.3 Power Distribution Board (PDB) Top View ATXPWR1 PMBUS1 ATX12V2 PWR_HDD1 ATX12V1 Description PMBus Connnector (PMBUS1) HDD Power Connector (PWR_HDD1) ATX 24pin Power Connector (ATXPWR1) ATX 8pin Power Connector (ATX12V1) ATX 8pin Power Connector (ATX12V2) Power Supply Connector (PSU2)
  • Page 42 4.4 Pin Definitions HDD Power Connectors The 4-pin connectors (PWR_HDD1) provide power to the (PWR_HDD2) backplane. GND1 (see p.33, No. 1, 2) GND2 +12V MiniSAS HD Connector This connector is used to (see p.33, No. 3) connect a mini-SAS HD cable to the motherboard.
  • Page 43 1U2FH-4L ATX Power Connector The PDB provides a 24-pin ATX (24-pin ATXPWR1) power connector. To use a 20-pin PSON# (see p.35, No. 3) ATX power supply, please plug it along Pin 1 and Pin 13. PWROK_PS 5VSB ATX 12V Power...

Table of Contents